User's Manual

ERP机型：PLA3582Q-GL-SMT00030A-V1
Designer：Sunny Date: 2020-09-24
描述： 感应灯说明书:PGA098，SMT000,REV.A，342x212mm, 128G双粉纸，双面4C+2专色印刷，
表面过哑油，风琴折两折页后再对折，RoHS2.0，REACH，POPs，PAHs，Prop65；
正面
折痕线
1、风琴折两折页 2、风琴后再对折 3、成型后尺寸：114x106mm
背面
正面 正面
正面
ERP P/N:
REV：0.1
KYMC
2915C
7540C
1. Make sure the light is fully charged before pairing and installing
by placing in sunlight for 8 hours or connecting to the USB port
and power supply, such as a mobile phone charger. This is
important to make sure there is enough power to initiate initial
paring with the Vision smart lock.
During daytime, when the light is in off mode, motion detection will
still continue to work and motion detection notifications will be sent
to your device through the LOCKLY app.
CHARGING
The Smart Motion Security Light is designed to charge primarily
through solar. However, it’s also equipped with a micro USB charging
port which can be used for initial charging or in cases where
weather conditions do not provide adequate sunlight.
Your battery level is below 60% when LED flashes and .
Optimize position to get more sunlight or use the charging port to be
fully charged.
MOTION DETECTION
At night or when it is dark light, activates whenever
motion is sensed. The green LED on the Vision smart
lock will flash and the LOCKLY app will send a push
notification. The smart motion security light will
stay on for 30 seconds after motion is detected.
The light will turn off and return to standby if
there is no longer any motion detected.
PERSON SENSING FUNCTION
When someone enters the sensing
range in the dark the light will turn
ON. After leaving the sensing
range for 10 seconds it will
return to standby mode.
During daytime, the smart
motion security light will
turn OFF automatically
for optimizing solar
charging.
2
SPECIFICATIONS
Connectivity
Bluetooth®
Power
1. Solar Panel 5.5V 1.2W Polycrystalline
Silicon, 18% Solar Conversion
2. USB (micro) backup charging port, 5V / 0.5A
Battery
LED
Luminous Flux
PIR Sensing Angle
Temperature
Sensing Distance
Waterproof Rating
Dimension
Lithium 3.7V, 1200 mAh
(22 pcs) 0.02W, 60mA | 24lm
248 lm
120˚
5500K - 6500K Daylight
3.5 - 20 feet (1 - 7 meters)
IP65
-4 - 140°F (-20 - 60°C)
2.95” x 2.70” x 4.75” (75 x 105 x 120 mm)
Weight 224 grams
Working Environment
Use and operation
Before setup and installation the light needs to be fully charged.
Please use the USB port to charge from a power supply for 1.5 hours
or place under direct sunlight for eight hours.
When the smart motion security light is not used for long periods of
time make sure the battery gets fully charged at least once every 3
months to help optimize battery life.
Optimum sunlight is always best for fully charging each day. During
periods of low sunlight, such as winter, it may take longer for the light
to charge which can have an effect on the duration the light will
operate. This is normal as with most solar powered lights.
SUPPORT
If you have any questions we are here to help. Please call customer
care at [phone] or email us at [e-mail].
This product comes with a limited one year warranty from the date of
purchase. Product registration and proof of purchase must be
provided in order to activate warranty.
Ideally the light should be mounted above door-frame where it
will receive ample sunlight. Ensure that it is no further than 15 feet
from the LOCKLY Vision smart lock.
Mount with either included self-adhesive flexible mounting plate
or screws. Mounting plate is suitable for most surfaces, including
siding, wood, stucco, brick, etc.
Note: screws include plastic anchors for stucco, rock or brick if
desired. Use template (right) for marking hole distance and location.
Template for marking hole distance and location.
Optimum
height
placement
6.5 - 13 feet
(2 - 4meters)
PAIRING WITH THE LOCK
2. Launch LOCKLY App and select “Add New” at the bottom of the
screen. Select Smart Motion Security Light from the “select
model” list then select your LOCKLY Vision smart lock as the lock
to pair with the light. Next you will hear 2 beeps from the Vision
lock. Confirm and select next step.
3. Turn the switch located on back to ON.
4. LED status light on front will blink red for 2s.
5. Press pairing button LED status light will blink yellow.
6. LED status light will turn to green, and lock will beep indicating
pairing has been successful.
LED INDICATORS DURING PAIRING
Pairing Mode: You will hear 2 short beeps and the green LED
indicator will flash on the Vision smart lock.
Successfully paired: You will hear a long beep and the green LED
indicator will flash on the Vision smart lock.
Unsuccessfully paired: You will hear 3 short beeps and the red
LED indicator will flash on the Vision smart lock.
Failed to enter pair mode: If smart lock fails to enter pairing mode
within 60 seconds you will hear 3 short beeps from the Vision smart
lock.
UN-PAIRING
Press pairing button on light for 8-secs. You will hear 2 short
beeps and the green LED status light will flash on the lock.
The light’s LED light panel will turn ON for 2 seconds, then OFF.
5
5
6
7
Setup (pairing with Vision smart lock)
1
3
Important reminders
15 feet max
from lock
Mounting area
Optimum height
6.5 - 13 feet
(2 - 4 meters)
VISION
™
SMART MOTION SECURITY LIGHT
USER MANUAL
6
2
7
5
4
1
3
LOCKLY Vision Smart Motion Security Light is
designed to work in conjunction with the LOCKLY
Vision smart lock + video doorbell. With its motion
sensing capability and LED light array it will alert
you to approaching visitors and illuminate your
doorway helping capture clear, full-color nighttime
video.
Introduction
TOP OF LIGHT
FEATURES
MOUNTING
LOCATION
Installation
2
• Auto-sync with LOCKLY Vision smart lock.
• Illuminates “live view” at night or when motion is detected.
• Detects motion day or night—sends alerts to your smartphone.
• Auto-records full color video at night when motion is detected.
• Auto mode only illuminates when motion is detected.
• Eco-friendly solar powered, high-efficiency, self-charging battery.
• Automatically turns off after 10s of someone leaving motion range.
• Backup USB charging port for initial charging or lack of sunlight.
• Easy setup and installation.
1) Solar Panel
2) Backup USB Charge Port
3) Motion Sensor
4) LED Light Panel
5) Setup Button
6) ON/OFF Switch (back)
7) LED Status Light
Screw alternative
Peel
x2
8
Peel adhesive backing and ensure nuts are tightened but allowing
enough room for threaded studs to slide into slots on back of light.
8
v. 01-2020.09
ADJUST MOTION SENSOR SENSITIVITY
Low (7ft)
Med (13ft)
High (20ft)
Low (7ft)
Med (13ft)
High (20ft)
Quick press to adjust the sensitivity level.
Long press (3s) to show the current Sensitivity setting and status.
Long press (3s) to EXIT settings.