User's Manual

R
安装操作说明：SD3702Q/PGA383，STM000，REV.A，240x92mm，80G书纸，
双面单黑印刷，三折页，ROHS2.0,REACH,POPs,PAHS,PROP65,
ERP机型：SD3702Q-GL-SMT00030A-V1
描述：
ERP P/N:
REV：0.1
Designed：Walter Date：2022-05-07
K
When you are installing the Door Sensor, make sure the arrows on
the Door Sensor is placed next to the arrow
from the Door Frame
Sensor.
OR
Door Frame
Sensor
Door Sensor
Magnet
Door Frame Door
Door Door Frame
Door Sensor
Magnet
Door Frame
Sensor
WHEN FACING YOUR DOOR
FROM THE INSIDE, DOOR HINGES
ARE ON THE RIGHT SIDE
WHEN FACING YOUR DOOR
FROM THE INSIDE, DOOR HINGES
ARE ON THE LEFT SIDE
The optimal location to install the Door Sensor is on the upper
corners of your door, away from the reach of children and pets.
IMPORTANT
-
Do not allow the battery to corrode or leak as this may cause
permanent damage to the product.
-
Make sure to insert battery on correct polarity as shown inside
the battery compartments.
- Do not use rechargeable batteries.
- When battery is drained, do not dispose with normal household
waste. Dispose via suitable recycling center. DO NOT BURN
When installed on your door, the distance between the Door
Sensor and the Door Frame Sensor must be less than 3/4” in
order for the sensor to work.
Gap - less than 3/4”
when installed.
WARNING: This product can expose you to chemicals including
Lead, which is known to the State of California to cause cancer.
For more information go to www.P65Warnings.ca.gov.
Preparation
Make sure you install the Door Sensor indoors on a clean and
dry surface. Gently wipe the surface of your door and door
frame where you wish to install the Door Sensor and make sure
it’s dry before installing. DO NOT INSTALL YET.
The Door Sensor comes in
two parts. Depending on
your door orientation, the
door sensor will be mounted
in different ways.
Lockly door sensor is based on bidirectional RF433.92MHz and
Lockly 2.0 proprietary encryption, providing communication
reliability, stability, and better security.
It is simple and very easy to install anywhere and it only uses
AAA battery for long and optimal operation. Door Sensor can
provide the ability to verify that your door is securely closed
and not ajar. It also sends push notifications to your phone
whenever the door unlocks or locked.
Part 1 - Door
Frame Sensor
Part 2 - Door
Sensor Magnet
Keep the Door Sensor away from direct sunlight, high heat
locations and large metal objects that may interfere with
wireless signals.
KEEP
AWAY
When installed on your door, the distance between the Door
Sensor and the Door Frame Sensor must be less than 3/4” in
order for the sensor to work.
WIRELESS DOOR SENSOR (PGA383)
Installation & User Manual
WWW.LOCKLYPRO.COM
Install the battery
Open the door sensor as shown, put in 1 AAA battery, please
pay attention to the positive and negative poles of the
battery.
LIFT
SLIDE
Slide and Lift to remove cover to
replace the AAA/LR03 battery.
Back
FCC Warning :
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
NOTE 1: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
- Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
NOTE 2: Any changes or modifications to this unit not expressly
approved by the party responsible for compliance could void
the user's authority to operate the equipment.
FCC Radiation Exposure Statement
The Secure Link Wi-Fi Hub complies with FCC radiation exposure
limits set forth for an uncontrolled environment. It should be
installed and operated with minimum distance 20cm between
the radiator & your body.
IC WARNING
This device contains licence-exempt transmitter(s) that comply
with Innovation,Science and Economic Development Canada’s
licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interfer
ence that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le
présent appareil est conforme aux CNR d’Innovation, Sciences
et Développement économique Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes:
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le
fonctionnement.
IC Radiation Exposure Statement
This equipment meets the exemption from the routine evaluation
limits in section 2.5 of RSS-102. It should be installed and operated
with a minimum distance of 20cm between the radiator and any
part of your body.
Cet équipement est conforme à l'exemption des limites d'évalu-
ation habituelle de la section 2.5 de la norme RSS-102. Il doit être
installé et utilisé à une distance minimale de 20 cm entre le
radiateur et toute partie de votre corps.
正面
正面
a风琴折2折页
c成型尺寸：80x46mm
正面
b对折