Installation Guide

ManualsBrandsLockly ManualsSmart HomeSecure Plus Matte Black Single-Cylinder Smart Alarmed Lock Latch with Keypad, Bluetooth and Fingerprint

LATCH EDITION

SECURE I SECURE PLUS I SECURE PRO

INSTALLATION MANUAL

For an online version of this installation guide and videos, visit:

http://lockly.com/help

INSTALLATION OVERVIEW & PARTS LIST

Lockly

Secure can be installed for both right swing and left swing doors. The lock ships ready for a right swing door installa-

tion. If you wish to change the orientation of the lock for a Left Swing door, go to Step 3 for instructions.

Exterior

3M TAPE

PM5X25mm, Door thickness 1-19/50"~1-69/100"(35~43mm)

PM5X35mm, Door thickness1-69/100"~1-97/100"(43~50mm)

* NOTE: You can either use T or U to stabilize the exterior part. T requires drilling an

extra hole. Use provided Template for drilling instructions if needed.

2-3/4"

(70mm)

2-3/8"

(60mm)

Measure distance between the center of the hole to the edge of door:

Use F1 if 2-3/8"(60mm) or F2 if 2-3/4"(70mm)

Tool for changing

handle orientation

Positioning rods for

installing part LK

STEP 1: PREPARING THE DOOR

STEP 2: INSTALLING THE LOCKSET

1 " - 2"

(35mm - 50mm)

2 "

54mm

25mm

Backset

" (60mm)

or 2

" (70mm)

IMPORTANT NOTICE

* You are not required to drill an extra hole on your door. We have provided 3M double sided

tape for you to help stabilize the lock during installation. Only drill a hole if you wish to have

added stability. Please refer to the provided template for drilling if needed.

2.1 Measure the distance between center of front door hole to the edge of your door

and select the correct lockset.

Select F1 if 2-3/8"(60mm) or F2 if 2-3/4"(70mm).

2-3/4"

(70mm)

2-3/8"

(60mm)

2.2 Install the lockset with the slanted side of the latch facing towards the closing direction.

Slanted side Facing Door Frame when closing

Example 1

Example 2

2.3 Secure lockset with provided screws, labelled G (Step 2.1) as shown.

STEP 3: CHANGING HANDLE ORIENTATION FOR

RIGHT OR LEFT SWING DOORS

The lock ships default for Right Swing Doors. You may skip STEP 3 if your door is a

Right Swing Door. To change your door handle orientation for a left swing door,

please continue reading.

How to determine if your door is a Right Swing or Left Swing door?

While facing the door, if the door hinges are on the right side of the door, you have a

Right Swing Door. If the hinges are on the left side of the door, you have Left Swing

Door.

Changing the Exterior Handle Orientation

Insert the key and rotate to align the

two white dots as shown in the picture.

IMPORTANT:

The following steps are only possible

when these two white dots are aligned!

3.1

Use the provided Clamping tool

(R) to push in the two metal pins

at the base of the lock handle,

located at the 3 o’clock and 9

o’clock positions, and remove the

handle once the pins are

compressed.

3.2

Rotate the handle 180 degrees to

the other side of the lock.

Using your fingers, press the two

pins located on the left and right

side of the the lock to insert the

handle back onto the lock.

3.3

Confirm that your installation was

complete by checking if the pins

are flush against the handle, and

has popped out. Adjust the handle

accordingly to make sure the pins

are fully decompressed and sits

flush against the surface.

3.4

Check that yor handle works

smoothly by giving it a turn up and

down. Your key can then be

taken out once it goes back to

the Horizontal position.

3.5

Changing the Interior Handle Orientation

Remove the screw by turning

counter clockwise and rotate the

handle 180

° in the direction of the

arrow as shown.

3.6

Securely screw clockwise as shown

to complete your handle orientation

change.

3.7

4.1

4.3

4.4

Peel paper layer OFF the 3M

tape and prepare for installation.

4.2

Install Part C with the holes

side into the base of the lock

and align the holes locate in

the 3 o’clock and 9 o’clock

position.

Insert locking pin Part D in

to the hole as shown above.

Lightly bend Part D so it’s locked into place

from moving as shown. We recommend using

pliers.

After you finshed bending the locking pin, turn

the handle to make sure it turns freely and

nothing is obstructed.

STEP 4: PREPARING LOCK FOR INSTALLATION

If you drilled a hole in Step 1, use pole (

Part U

) and securely tighten with a flat head screw-

driver by turning it clockwise onto the lock. If you did not drill a hole in step 1, you can leave

this pole removed.

Exterior

STEP 5: INSTALLING THE LOCK (EXTERIOR)

Install the exterior lock as shown

to the left by aligning the lock

straight and passing the cable and

attached rods through the lockset.

5.2

Pass the square rod (Part C)

through the center of the lockset,

and the round rods through the

sides in their respective holes. The

cable should run undeneath the

lockset.

5.3

Align the lock straight and press

hard (if you use the 3M tape in

step 4.4) to secure the top of the

lock.

5.4

STEP 6: INSTALLING THE LOCK (INTERIOR)

Interior

6.1

(Mounting Plate)

6.3

Insert positioning rods (Part V)

into the the holes to the left and

right of the square rod (Part C).

The holes are located at the 3

o’clock and 9 o’clock positions.

6.2

Part LK (Interior Mounting Plate)

will go against the interior side of

your door. Remove the paper

layer off of the 3M tape and match

the positioning rods on the bottom

of the plate to the corresponding

left and right holes.

Install the side with the black

plastic seal against the door.

Positioning rods slide through these holes.

Pull the cable from the exterior

lock through the rectangular

hole underneath the positioning

rods and square rod.

Secure the hole above the

square rod with Part O screw.

O Screw

6.4

Remove the position rods (Part V)

and replace them with Part O

screws. Tighten clockwise until the

mounting plate is secure.

* If you have drilled a hole on the

top in Step 1, please secure the

hole with part M1 or M2 depending

on your door thickness. Skip this if

no hole was drilled in Step 1.

*Secure top with M1 or M2

PM5X25mm

PM5X35mm

Plug the cable that is coming through the

door into the Interior lock. Make sure

you match the direction of the plug

correctly and matching the red side of

the plug with the red side on the lock.

6.5

Align the square rod to the Interior lock

and attach the Interior lock to the Interior

mounting plate.

While you are doing so, gently push

some of the excess cable through the

rectangular hole into the door.

Place the remaining cable against the

interior side of the Interior lock so the

Interior lock sits securely onto the

mounting plate.

6.6

P (3X)

Once the Interior lock is flush against the

mounting plate, secure the lock to the

plate by screwing clockwise by using

supplied screws (Part P).

6.7

Insert 4 AA batteries into the lock by

matching the postive (+) and negative (-)

orientation markings on the batteries to

the battery chamber.

Secure the battery cover by sliding the

cover over the lock and turning the screw

clockwise on top until tight.

6.8

GETTING STARTED - YOU WILL NEED

All the parts you need to install the Lockly Secure Latch Edition is included in your

package. However, we do need a few tools.

Phillips Screwdriver

Flathead Screwdriver

Ruler

Required Tools Optional

Screwdriver with drill bits

Drilling is not required to install the lock, and is optional. However if you are

installing your lock on a brand new door, a drill is required if there are no holes

prepared for lock installation.

1.1

If you are installing the Lockly Secure

smart lock on an existing door, please

remove existing door hardware and latch

or bolts before installing the new lock.

You can remove most existing door locks

with a screwdriver.

If you are having problems removing

your existing door lock or unsure if what

you are doing can damage the existing

door, please contact a locksmith or the

current door hardware manufacturer for

assistance.

1.2

After removing the exisiting lock, make sure your door is properly prepared. If you

need to drill holes in your door, please use supplied templates to assist.

Measure and confirm your door is

between

1 " - 2" (

35mm - 50mm).

Measure and confirm the hole in the

door is

2 "

(54mm).

Measure and confirm that the

backset is between

2 "

(60mm) to

2 "

(70mm).

Measure and confirm that hole in the

door edge is 1” (25mm).

1.3

1.4

1.5

1.6

STEP 7: INSTALLING THE DOOR STRIKE

G(2x)

Make sure the slanted side of Part F1/F2 is closing against

the slanted part of Part H before fixing it on to door frame.

DOOR STRIKE INSTALLATION

Close your door to see if your lock closes securely with your existing door strike. If

the lock closes securely, you may keep the existing door strike without removing the

old hardware. However, it’s recommended that you use our door strike.

STEP 8: FINISHING INSTALLATION

You’re all done! You have completed the Lockly

Secure physical lock installation and now

you’re ready to get the lock set up. Download the Lockly

app from the iOS or Google Play

Store to complete your lock set up.

Scan or visit Lockly.com/app