SECURE I SECURE PLUS I SECURE PRO DEADBOLT EDITION INSTALLATION MANUAL
INSTALLATION OVERVIEW K H1 H2 G F H M D B J I C Q P O N A LocklyTM Secure can be fitted for both right swing doors and left swing doors.
PARTS LIST C E N P Q F G x8 A B D 3M Double Sided Tape- EVA Sticker J K H1 x2 H2 x2 I x3 M x3 O x5
STEP 1: PREPARING YOUR DOOR 1/2" 12mm 1-3/8"—2" (35mm—50mm) 1" 25mm Drill Hole 3-7/8"(98mm) Drill Hole 2-3/8"(60mm) or 2-3/4"(70mm) IMPORTANT NOTICE You are not required to drill a hole in your door. We have provided 3M double sided tape for you to help stabilize the lock during installation. Only drill a hole if you wish to have added stability. Please refer to the provided templates for drilling if needed. Make sure your door is prepped for installation prior to installation.
STEP 2: ADJUSTING THE BOLT If the latch holes are centered in the drilled hole, no adjustment is needed. If NOT, adjust the latch as shown below. Adjust as shown below (as needed) 2-3/8" 2-3/4" B C A 2-3/4" 1 Initial position of A: 2-3/8" 2 Push toggle button "A" downwards and pull part "B" outwards. 3 Pull "C" to 2-3/4" and release button "a". Now the backset has been adjusted to 2-3/4".
STEP 3: EXTENDING THE BOLT O P(2X) N Extend the latch bolt as shown. When installing the latch, make sure the position of the "+" mark is on the bottom part of the latch.
STEP 4: PREPARING THE EXTERIOR ASSEMBLY Vertical X When the bolt is extended, the torque blade should be kept in a vertical position. *REMOVE COUNTERCLOCKWISE 3M GO TAPE ES HER E X D B D C Install “D” & “C” on “B” in order as shown. B C (Pole Removed) *The pole (Labeled X) is used if you drilled a hole in your door. It is not required. If you did not drill a hole in your door, please remove this pole with a flathead screwdriver by turning it counter clockwise.
STEP 5: INSTALLING THE EXTERIOR ASSEMBLY Note: Please use rotate the torque blade into the vertical position for installation. A. When the bolt is extended, the torque blade should be kept in a vertical position. A B B. Make sure the cable goes underneath the latch. INTERIOR VIEW EXTERIOR VIEW Route cable through center hole, then push it into side hole.
STEP 5 (CON’TD): INSTALLING THE EXTERIOR ASSEMBLY H1 H2 H * I(2X) H * I(2X) Before screwing check the vertical alignment for the mounting plate and exterior assembly. * H is only required if you drilled a hole in your door. If you did not drill a hole in your door, please do not insert H. Depending on your door thickness, use H1 or H2 screws for the doors. Doors with thickness of 35-43mm, use H1. Doors with thickness of 43-50mm, use H2.
STEP 6: INSTALLING INTERIOR ASSEMBLY J Connect the cable. Please insert the RED face of the cable connector into the socket marked in RED. Make sure the connector is securely fixed to the socket. Torque Blade Thumb turn shaft Push the thumb turn shaft into the torque blade.
STEP 7: SECURING Lockly TM SECURE M A A. Make sure the thumbturn is in a vertical position. Make sure the cover is removed so you can install batteries, but don’t install batteries yet.
STEP 8: INSTALLING BATTERIES + - + - + + First install 3 of the 4 batteries. Before installing the last battery, press and hold the PROGRAM button while installing the last battery until you hear a beep from LocklyTM. LocklyTM will then perform a self check and the keypad screen will start to initiate. This self check will automatically determine and set your door lock to a left open or right open door. The self-check process is very important step to ensure the installation is done properly.
STEP 9: FINISHING INSTALLATION Install the door strike. Install the door strike to your door frame and proceed to the last step of installation of your new lock. Notice: Do not install the battery cover just yet you’ll need to program LocklyTM before doing so. O(2X) P Q You’re all done! You have completed the LocklyTM Secure physical lock installation and now you’re ready to get the lock set up. Download the LocklyTM app from the iOS or Google Play Store to complete your installation.
For an online version of this installation guide and videos, visit: http://lockly.