SECURE INSTALLATION GUIDE DEADBOLT EDITION PGD728 | PGD728F | PGD728FC
SECURE Go to Lockly.com/installation to watch a video version of this installation guide. OR Download the BILT app in the App Store or on Google Play for step-by-step interactive 3-D walk-through installation instructions.
Welcome! This guide will walk you through step-by-step how to install and get your Lockly Secure up and running. Installation generally takes less than 30 minutes. If you have any questions please reference our online support at: Lockly.com/support or call (669) 500-8835 for help.
Preparation To complete installation, you would need the following: Phillips Screwdriver Flathead Screwdriver Tape measure or ruler Prepare door and remove existing lock. If necessary, use provided Installation Template to prepare door. 2-⅜" (60mm) or 2-¾" (70mm) 1-⅜" (35mm) to 2" (50mm) *Optional 1" (25mm) 2-⅛" (54mm) * Use goggles to protect eyes if you need to drill door holes.
Step 1 ADJUST DEADBOLT AND INSTALL 1: Deadbolt slot must align to the center of the door hole. Adjust as shown if needed. 2-3/4" (70mm) or 2-3/8” (60mm) The deadbolt comes set to 2-3/4" (70mm). Adjust length to 2-3/8” (60mm) if necessary. (wear gloves to protect from possible pinching). B A B Push the crank A to extend the deadbolt B C D Deadbolt comes set at 2-3/4" (70mm).
Step 1 ADJUST DEADBOLT AND INSTALL continued 2: Extend the deadbolt by inserting a flat-head screwdriver into the slot and turning clockwise. 3: Insert the deadbolt into door edge hole, make sure that the right side is up and the slot is in the vertical position. Secure with 2 K screws.
Step 2 INSTALLING THE EXTERIOR ASSEMBLY 1: To secure Exterior Assembly of lock, peel the cover off the adhesive strips B Peel paper off the Adhesive tape *This hole (O) is for the optional Slotted Barrel Extension provided for stabilizing your lock. It will require drilling extra hole on your door (See template as provided). Alternatively, you may use the double-sided adhesive tape provided which serves the same purpose if you do not want to drill a hole.
Step 3 INSTALLING THE INTERIOR ASSEMBLY (F) 1: Check interior mounting plate D alignment to your door hole before securing with adhesive strips. 2: Align and secure mounting plate with adhesive strips. Guide connection cables through the hole and secure to the lower left notched hole. Remove key when finished G (2X) Leave deadbolt extended 3: Insert and tighten by hand 2 G screws located on the left and right of the blade.
Step 3 INSTALLING THE INTERIOR ASSEMBLY (F) continued 5: Plug the cable coming through mounting plate D into the interior assembly F as shown. Tuck cable under eyelet hooks and route to the right on interior assembly F . Y X Plug X into Y , match red side of plug with red on socket - insert tightly. Install Cable Remove Cable 2 1 IMPORTANT: If you need to disconnect this cable, use a screwdriver to hold down the tab (marked red) before carefully unplugging.
Step 3 INSTALLING THE INTERIOR ASSEMBLY (F) continued PROGR PROGR AM AM PROGR RESET AM RESET RESET Torque Blade Thumb turn shaft I 2X Align torque blade with thumb turn shaft, make sure both are in the vertical position. 6: Before placing the interior assembly onto the mounting plate, ensure the thumb turn is vertical. 7: Place the interior assembly against the mounting plate and make sure the torque blade is inserted to the thumb turn shaft.
Step 4 1 INSTALLING BATTERIES 2 3 PRESS & HOLD 4 1: With door open and deadbolt fully extended, place ribbon inside compartment and insert 4 batteries (note correct -/+ polarity). 2: After all batteries are installed, PRESS and HOLD the program button for 10S. The lock will automatically start self-check (release program button once check starts). The self-check process determines right or left swinging door and is very important to ensure correct installation.
Step 5 INSTALLATING DOOR STRIKE Use the supplied door strike or use your existing as long as deadbolt operates smoothly without binding or catching. K(2X) L N IMPORTANT: because doors and frames vary in design it may be necessary to make slight adjustments to your strike plate and/or dust box in order to ensure smooth deadbolt operation. This is very important.
Step 6 DOWNLOAD LOCKLY APP Congratulations! You have completed the Lockly Secure physical lock installation. To complete your setup, download the Lockly app from the App Store or on Google Play and follow on-screen instructions. Scan or visit Lockly.
Add more Smart to your Home Secure Link Wi-Fi Hub Add the optional Lockly Secure Link Wi-Fi Hub, together with the free Lockly app, it's easier than ever to securely control and manage your door from anywhere, anytime. Real-time, monitoring, & status Monitor open/closed door status with real-time alerts sent to your smart phone, no matter where you are. Grant access, even when you’re not home Lock and unlock door from anywhere.
FCC Warning： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
INSTALLATION OVERVIEW AND PARTS LIST Parts List Labeled As Description A Keys F H E M Exterior M PE ive TA Adhes D I esive Adh E TAP O 2X B G 2X A J L K 4X V ACC20211201 N U LOCK SERIAL PGDXXXXXXXXXXXXXXXX ACTIVATION CODE Lockly Secure can be fitted for both right swing doors and left swing doors.
SECURE For the most up to date version of this guide please visit: Lockly.com/help We’re here to help! Email: help@Lockly.com © Copyright 2022 Lockly All rights reserved USA Patent NO. US 9,881,146 B2 | USA Patent NO. US 9,853,815 B2 | USA Patent NO. US 9,875,350 B2 |USA Patent NO. US 9,665,706 B2 | USA Patent NO. US 11,010,463 B2 | AU Patent NO. 2013403169 | AU Patent NO. 2014391959 | AU Patent NO. 2016412123 | UK Patent NO. EP3059689B1 | UK Patent NO.
