DEADBOLT EDITION - SECURE I SECURE PLUS I SECURE PRO INSTALLATION MANUAL
INSTALLATION OVERVIEW K H1 H2 G F H M D B X J I C Q P O N A LocklyTM Secure can be fitted for both right swing doors and left swing doors.
PARTS LIST X C E N P Q F G x8 A B D 3M Double Sided Tape- EVA Sticker J K H1 x2 H2 x2 I x3 M x3 O x5
STEP 1: PREPARING YOUR DOOR 1/2" 12mm 1-3/8"—2" (35mm—50mm) 1" 25mm Drill Hole 3-7/8"(98mm) Drill Hole 2-3/8"(60mm) or 2-3/4"(70mm) IMPORTANT NOTICE You are not required to drill a hole in your door. We have provided 3M double sided tape for you to help stabilize the lock during installation. Only drill a hole if you wish to have added stability. Please refer to the provided templates for drilling if needed. Make sure your door is prepared prior to installation.
STEP 2: ADJUSTING THE DEADBOLT If the latch holes are centered in the drilled hole, no adjustment is needed. If NOT, adjust the latch as shown below. Adjust as shown below (as needed) 2-3/8" 2-3/4" B C A 2-3/4" 1 Initial position of A: 2-3/8" 2 Push toggle button "A" downwards and pull part "B" outwards. 3 Pull "C" to 2-3/4" and release button "a". Now the backset has been adjusted to 2-3/4".
STEP 3: EXTENDING THE DEADBOLT N O(2X) N Extend the deadbolt as shown. When installing the deadbolt, make sure the position of the "+" mark is on the bottom part of the latch.
STEP 4: PREPARING THE EXTERIOR ASSEMBLY X Vertical When the bolt is extended, the torque blade should be kept in a vertical position. X 3M D SID OUB ED L TA E PE D B D C 3M D SID OUB ED L TA E PE B C Install “D” & “C” on “B” in order as shown. *This hole (X) is for the optional post provided for stabilizing your lock. It will require drilling extra hole on your door (See template as provided).
STEP 5: INSTALLING THE EXTERIOR ASSEMBLY Note: Please rotate the torque blade into the vertical position for installation. (1). When the bolt is extended, the torque blade should be kept in a vertical position. (2) (1) (2). Make sure the cable goes underneath the latch. INTERIOR VIEW EXTERIOR VIEW Route cable through center hole, then push it into side hole.
STEP 5 (CON’TD): INSTALLING THE EXTERIOR ASSEMBLY H1 H2 H * I(2X) H * I(2X) Before screwing check the vertical alignment for the mounting plate and exterior assembly. * H is only required if you drilled a hole in your door. If you did not drill a hole in your door, please do not insert H. Depending on your door thickness, use H1 or H2 screws for the doors. Doors with thickness of 35-43mm, use H1. Doors with thickness of 43-50mm, use H2.
STEP 6: INSTALLING INTERIOR ASSEMBLY J Connect the cable. Please insert the RED face of the cable connector into the socket marked in RED. Make sure the connector is securely fixed to the socket. Torque Blade Thumb turn shaft Push the thumb turn shaft into the torque blade.
STEP 7: SECURING Lockly TM SECURE M A A. Make sure the thumbturn is in a vertical position. Make sure the cover is removed so you can install batteries, but don’t install batteries yet.
STEP 8: INSTALLING BATTERIES - + + + + - First install 3 of the 4 batteries. Before installing the last battery, press and hold the PROGRAM button while installing the last battery until you hear a beep from LocklyTM. LocklyTM will then perform a self check and the keypad screen will start to initiate. This self check will automatically determine and set your door lock to a left open or right open door. The self-check process is very important step to ensure the installation is done properly.
STEP 9: INSTALLING DOOR STRIKE Install the door strike. Install the door strike to your door frame and proceed to the last step of installation of your new lock. You may use our supplied door strike or use your existing door strike as long as the deadbolt moves smoothly in and out of the door strike. As there are many types of doors, you may need to make slight adjustments so the dead bolt moves smoothly.
STEP 10: INSTALLING THE SECURE LINK WI-FI HUB The Lockly™ Secure Link Wi-Fi Hub comes in two parts. Each part of the Secure Link is crucial to enable voice assistant features and live monitoring and control of your Lockly™ device. The Wireless Door Sensor is optional but highly recommended as they provide the ability to verify that your door is securely closed and not ajar.
STEP 11: SETTING UP THE SECURE LINK WI-FI HUB You should install the Secure Link Wi-Fi Hub after you have successfully finished installation and set up of your Lockly™ Smart Lock. Refer to your appropriate Lockly™ Smart Lock Installation Guide and User Manual that came with the lock for reference. The Secure Link Wi-Fi Hub (Part A) can be plugged into any standard 5V 1A USB port or use the UL certified USB AC adapter included in this box (recommended).
Plug the Secure Link Wi-Fi Hub into the 5V 1A USB AC adapter and plug the AC adapter to your wall socket. A red LED indicator light will flash slowly to indicate that the Wi-Fi Hub is ready to connect. USA Outlet Shown LED Indicator is located next to the Setup Button Once you have confirmed that your Secure Link Wi-Fi Hub is ready to connect to your lock, open the Lockly™ app to get started. In case you have not downloaded our app, you can scan the QR code to the left or visit https://lockly.
STEP 12: USING THE SECURE LINK WI-FI HUB Before you set up your Wi-Fi Hub, make sure you are standing in between your Lockly Smart Lock and Secure Link Wi-Fi Hub. For best connection, the distance between the Wi-Fi Hub and your smart lock should be 10 feet or less.
Secure Link Installation Checklist. I’m excited for my new Lockly smart lock, now compatible with Alexa and Google Assistant.* You have a Lockly Smart Lock already, and now adding the Wi-Fi Hub The Secure Link Wi-Fi Hub is installed within 10 feet of your Lockly Smart Lock You have the Lockly App installed on your iOS or Android device. Your smartphone Bluetooth connection is ON and connected to your Lockly device. You are standing between your smart lock and the Secure Link Wi-Fi Hub.
STEP 13: CONFIGURING THE SECURE LINK WI-FI HUB First, make sure the smartphone you are using to add the Wi-Fi Hub is connected to your 2.4 GHz Wi-Fi Network. Next, open your Lockly App and select the main menu from the upper left corner. (Image shown with iOS demo).
If you have never connected the Secure Link Wi-Fi Hub to your smart lock, the Secure Link should have a slow flashing RED LED Indicator. Press and hold the Setup Button located on the top of the Wi-Fi Hub for 3 seconds until you see the RED LED Indicator start to rapidly flash. Press and Hold 3 Seconds If you don’t see anything appear with a Bluetooth icon and a name starting with PGH200... simply click the Refresh button on the upper right to rescan.
If you are already connected to a 2.4 Ghz compatible Wi-Fi network, it should display the network name. (See example below) Enter your Wi-Fi password in the next line next to the icon, then click “Next Step” to continue. Select if your Wi-Fi Hub LED Indicator light is ON and solid. Select if your Wi-Fi Hub LED Indicator light is ON and still flashing after 2-3 minutes. *Actual screen may differ depending on device and app version Please follow on -screen instructructions.
Congratulations! Your Secure Link Wi-Fi Hub is now set up. Below are some quick information for troubleshooting. No Indicator Light Your Wi-Fi Hub has no power. Check your the power supply. Rapid Flashing Indicator Light Your Wi-Fi Hub is in setup mode. Setup mode can be entered by pressing the setup button for 2 seconds. Setup mode will last approx 2 minutes. Slow Flashing Indicator Light Your Wi-Fi Hub has power. It’s not connected to any wireless network.
STEP 14: ADDING THE DOOR SENSOR Adding the door sensor (Part B) is optional, however we strongly recommend installing the Door Sensor as it provides the ability to verify that your door is securely closed and not ajar and also send push notifications to your phone on the status of your door when someone opens and closes the door. Depending on your door orientation, your Door Sensor will be mounted different ways. The Door Sensor comes in two parts.
Keep the Door Sensor away from direct sunlight, high heat locations and large metal objects that may interfere with wireless signals. KEEP AWAY The optimal location to install the Door Sensor is on the upper corners of your door, away from the reach of children and pets.
When you are installing the Door Sensor, make sure the arrows on the Door Sensor is placed next to the arrow from the Door Frame Sensor. OR When installed on your door, the distance between the Door Sensor and the Door Frame Sensor must be less than 3/4” in order for the sensor to work. Gap - less than 3/4” when installed. When you are ready to install, pull the plastic tab at the back of the Door Frame Sensor to activate the sensor.
Congratulations! The Door Sensor is now set up. The Secure Link Wi-Fi Hub works with other Smart Home devices. Check on the status or remote lock and unlock your door by your voice using Amazon Alexa or Google Home Assistant. To setup your lock to work with either of those platforms, download the Amazon Alexa or Google Home Assistant app and add a new skill with Amazon Alexa or an Action with Google Home Assistant.
Certified Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
We’re here to help! help@lockly.com https://lockly.