MODEL 7S INSTALLATION GUIDE DEADBOLT EDITION
Go to LOCKLY.com/installation to watch a video version of this installation guide. OR Download the BILT app in the Apple or Google Play store for step-by-step interactive 3-D walk-through installation instructions.
Welcome! This guide will walk you through step-by-step how to install and get your LOCKLY® up and running. Installation generally takes less than 30 minutes. If you have any questions please reference our online support at: LOCKLY.com/support or call (669) 500-8835 for help.
Preparation To complete the installation you will need: Phillips Screwdriver Flathead Screwdriver Tape measure or ruler Prepare door: remove existing deadbolt or use provided template to bore new holes.
Step 1 ADJUST DEADBOLT AND INSTALL Deadbolt slot must align to the center of the door hole. Adjust as shown if needed. 2-3/4" (70mm) or 2-3/8” (60mm) The deadbolt comes set to 2-3/4" (70mm). Adjust length to 2-3/8” (60mm) if necessary. (wear gloves to protect from possible pinching). B A B Push the crank A to extend the deadbolt B C D Deadbolt comes set at 2-3/4" (70mm).
Step 1 ADJUST DEADBOLT AND INSTALL continued Extend the deadbolt by inserting a flat-head screwdriver into the slot and turning clockwise. Insert the deadbolt into mortise flush with door edge, make sure that the right side is up and the slot is in the vertical position. Secure with 2 K screws.
Step 2 INSTALLING THE EXTERIOR ASSEMBLY Check the exterior assembly (B) alignment to door hole and deadbolt before peeling off film on adhesive strips. B Peel paper off the Adhesive tape M Peel film from adhesive strips and make sure torque blade is in the vertical position with the deadbolt extended. Place assembly and torque blade through the deadbolt slot and guide connection cables through the cross-bore hole under the deadbolt as shown.
Step 3 INSTALLING THE INTERIOR ASSEMBLY (F) 2: Align and secure mounting plate with adhesive strips. Guide connection cables through the hole and secure to the lower left notched hole. 1: Check interior mounting plate (K) alignment to your door hole before securing with adhesive strips. Remove key when finished G (2X) Leave deadbolt extended 3: Insert and tighten by hand 2 G screws located on the left and right of the blade.
Step 3 INSTALLING THE INTERIOR ASSEMBLY (F) continued Plug the cable coming through mounting plate D into the interior assembly F as shown. Tuck cable under eyelet hooks and route to the right on interior assembly F . Y X Plug X into Y , match red side of plug with red on socket - insert tightly. NOTE: If you need to disconnect the cable, make sure to press the snap tab to release the plug before carefully pulling it out. Do not force, as this may result in damaging the lock.
Step 3 PROG RAM INSTALLING THE INTERIOR ASSEMBLY (F) continued RESE T PROG RAM PROG RESE T Torque Blade RAM RESE T Thumb turn shaft I 2X Align torque blade with thumb turn shaft, make sure both are in the vertical position. Before placing the interior assembly onto the mounting plate, ensure the thumb turn is vertical. Place the interior assembly against the mounting plate and make sure the torque blade is inserted to the thumb turn shaft.
Step 4 INSTALLING BATTERIES 1 2 3 4 PRESS & HOLD 1: With door open and deadbolt fully extended, place ribbon inside compartment and insert 3 batteries only (hold on inserting the 4th) in bottom row (note correct -/+ polarity). 2: Press and HOLD the program button, continue to hold and install the 4th battery. The lock will automatically start self-check (release program button once check starts).
Step 4 INSTALLING BATTERIES continued 3: Once self-check completes ensure the lock operates smoothly by manually locking and unlocking the door using the thumb turn on the interior assembly. The deadbolt should operate smoothly without any interference or binding. If necessary, repeat step 2 and ensure that (a) the deadbolt was extended and (b) the torque blade was inserted vertically while the deadbolt was extended. 4: Swipe your hand across the touch screen keypad, the lock should close (lock).
Step 5 INSTALLATING DOOR STRIKE Use the supplied door strike or use your existing as long as deadbolt operates smoothly without binding or catching. K(2X) L N IMPORTANT: because doors and frames vary in design it may be necessary to make slight adjustments to your strike plate and/or dust box in order to ensure smooth deadbolt operation. This is very important.
Step 6 DOWNLOAD LOCKLY® APP Congratulations! You have completed the LOCKLY physical lock installation. To complete your setup, download the LOCKLY app from the iOS or Google Play app Store and follow onscreen instructions. Scan, visit app store, or go to LOCKLY.
Smart Home Ready SECURE LINK You can add live status monitoring and voice control capabilities to your LOCKLY® Smart Lock with Amazon Alexa or Google Assistant via installing the Secure Link (PGH200) Wi-Fi Hub and Door Sensors (Sold Separately) Know it’s Closed. Wireless Door Sensors No more worries wondering if your door was shut when you locked your door. Included is a set of wireless door sensors that can provide accurate information on the status of your door.
FCC Warning： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
INSTALLATION OVERVIEW AND PARTS LIST Parts List Labeled As F H E M Exterior M PE ive TA Adhes D I esive Adh E TAP 2X B G 2X A J N L U K 4X AUTHENTIC LOCKLY PRODUCT | DESIGNED IN USA | CARD IS PRINTED WITH A SPECIFIC PATTERN LOCK SERIAL ACC20200402 PGDxxxxxxxxxx ACTIVATION CODE LOCKLY® can be fitted for both right swing doors and left swing doors. xxxxxxxx SCAN & SAVE SECURE ADDITIONAL DOORS AT A DISCOUNT: HTTP://WWW.LOCKLY.COM/MORE LOCKLY.
Connect with us @meetlockly | #LOCKLY Reference installation parts overview foldout.
We’re here to help! Email: help@LOCKLY.com For the most up to date version of this guide please visit: LOCKLY.
