Owners Manual Assembly Instructions BOILING KIT Models: LCTSKSS42 • LCTSKSS60 • LCTSKSS80 LCTSKSS90 • LCTSKSS100 WARNING READ INSTRUCTION MANUAL BEFORE ATTEMPTING TO ASSEMBLE OR OPERATE THIS PRODUCT. Adult assembly required. Keep screws and parts out of reach of children. INSTALLER: Leave this manual with the consumer. CONSUMER: Keep this manual for future reference.
This instruction manual contains important information necessary for the proper assembly and safe use of the appliance. Read and follow all warnings and instructions before assembling and using the appliance. Follow all warnings and instructions when using the appliance. Keep this manual for future reference. SAFETY SYMBOLS Basic safety precautions should always be observed when using this appliance. Read and understand the meaning of these symbols before assembling and using this appliance.
TABLE OF CONTENTS Warnings 2, 4-7 Parts Diagram and Parts List 8 Hardware 9 Assembly Instructions 9-12 Operating Instructions 13-15 Care and Maintenance 15 Troubleshooting 16 Warranty Information 17 WARNING Do not place an empty cooking pot on the appliance or allow a filled pot to boil dry while appliance is in operation. Use caution when placing anything in the cooking pot while the appliance is in operation. lococookers.
WARNINGS SAVE THESE INSTRUCTIONS • THIS APPLIANCE IS ONLY INTENDED FOR HEATING WATER . . . NOT OIL OR GREASE. • When cooking, always have a Type BC or ABC fire extinguisher readily available. • The installation must conform with local codes or, in absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Storage and Handling of Liquefied Petroleum Gases, ANSI/NFPA 58; or Natural Gas and Propane Installation Code, CSA B149.1; Propane Storage and Handling, CSA B149.2.
WARNINGS • The pressure regulator and hose assembly supplied with the appliance must be used. Replacement pressure regulators and hose assemblies shall be those specified by the appliance manufacturer. Replace only with regulator Model No. GYK-5/8, KR-126+GDH1, FR0010Q or 101E Series. Height • Never drop food or accessories into hot cooking liquid. Lower food and accessories slowly into the cooking liquid in order to prevent splashing or overflow.
WARNINGS: LP TANK DANGER 1. Do not store a spare LP gas cylinder under or near this appliance. 2. NEVER fill the cylinder beyond 80% full. 3. If the instructions in 1 and 2 are not followed exactly, a fire causing serious injury or death may occur. 4. The safety release valve on the LP tank could activate the leaking of gas and cause a severe fire and increase the risk of serious injury or death. 5.
WARNINGS: LP TANK LP TANK FILLING: • Use only licensed and experienced dealers. • LP dealer must purge tanks before filling. • Dealer should NEVER fill LP tank more than 80% of LP tank volume. Volume of propane in tanks will vary by temperature. • A frosted regulator indicates gas overfill. Immediately close LP tank valve and call LP gas dealer for assistance. • Do not release liquid propane (LP) gas into the atmosphere. This is a hazardous practice.
PARTS DIAGRAM NOTE: Wash all parts that will come into contact with food with warm soapy water. Rinse and towel dry.
ASSEMBLY INSTRUCTIONS Tools required: Phillips head screwdriver • Adjustable wrench (Not included) Assembly Hardware 8 B M6 Washer 8 C M6x22 Screw A M6x14 Screw 1 Do not fully tighten screws at this time. 2 D M5x10 Screw 2 4 Venturi Tube A 6 A Electrode fits into slot. x4 B B x4 A B Make sure venturi tube exits side of stand with two holes. 2 Fully tighten screws. A B 7 A x2 B x2 lococookers.
ASSEMBLY INSTRUCTIONS 3 A x2 B x2 C D 10 C x2 B A B D A D 11 x2 Fully tighten all four burner assembly screws from step 1 after venturi shield is installed. Insert electrode wire through hole in venturi shield.
ASSEMBLY INSTRUCTIONS 4 Plug electrode wire into back of ignitor. 5 9 Unscrew ignitor button and insert AA battery negative (–) end first. lococookers.
ASSEMBLY INSTRUCTIONS 6 2 TWIST & DRAINTM 1. Lift the basket above the pot. 2. Rotate the basket 90 degrees. 3. Lower so that bottom tabs on basket rest on tabs inside pot for draining. 1 1 3 2 3 DETERMINING THE MAXIMUM FILL LEVEL WHEN USING A VESSEL WITHOUT A MAXIMUM FILL LINE: 1. Place your food into the basket. 2. Place the basket and food into the empty cooking vessel. 3. Fill the vessel with water just until the food is completely submerged.
OPERATING INSTRUCTIONS CONNECTING REGULATOR TO LP TANK: 1. Place LP tank on a secure, level and stable surface. 2. Turn regulator control knob to the OFF position by rotating counterclockwise to a full stop. 3. Turn LP tank OFF by turning hand wheel clockwise to a full stop. 4. Remove the protective cap from LP tank. Always use cap and strap supplied with valve. DO NOT use a POL transport plug. It will defeat the safety feature of the valve. 5. Hold regulator, insert nipple into LP tank valve.
OPERATING INSTRUCTIONS 3. Ensure a minimum of 24 inches (61 cm) separate the LP tank and the appliance. WARNING LP hose is a tripping hazard. Special Care must be observed. 4. Open the LP tank valve fully by turning counterclockwise. 5. Electronic Ignitor Lighting: Press and continually hold the ignition button while rotating the regulator control knob clockwise until the burner is lit. DO NOT stand with head or arms over burner.
OPERATING INSTRUCTIONS CARE AND MAINTENANCE DISCONNECTING REGULATOR FROM LP TANK: 1. Turn regulator control knob counterclockwise to the OFF position. 2. Turn LP tank OFF by turning hand wheel clockwise to a full stop. 3. Turn the coupling nut counterclockwise to loosen the connector. Loosen by hand only. DO NOT use tools. 4. When disconnected, the regulator should be hung from the hook attached to the appliance.
TROUBLESHOOTING PROBLEM Burner will not light. Burner does not stay lit. Water does not reach desired cooking temperature. 16 POSSIBLE CAUSE Bad connection between the regulator and LP tank. SOLUTION Make sure the regulator coupling nut is fully tightened on the LP tank valve. The LP tank is empty. Refill LP tank at an authorized dealer or purchase new filled LP tank. Ignition button was not pushed Press and hold the ignition and held. button until burner is lit. Battery not installed correctly.
WARRANTY INFORMATION The appliance has been manufactured under the highest standards of quality and workmanship. We warrant to the original consumer/purchaser that all aspects of this product will be free of defects in material and workmanship for one (1) year from the date of purchase. A replacement for any defective part will be supplied free of charge for installation by the consumer. Requests for expedited shipments of warranted parts will be at the consumer’s/purchaser’s expense.
LoCo - Crazy Good Cookers, LLC. 506 Manchester Expressway • Suite A2 • Columbus, Georgia 31904 800-391-0436 • Email: customerservice@lococookers.com Connect with us @lococookers • lococookers.
Manual del propietario Instrucciones de montaje KIT HERVIDOR Modelos: LCTSKSS42 • LCTSKSS60 • LCTSKSS80 LCTSKSS90 • LCTSKSS100 ADVERTENCIA LEA EL MANUAL DE INSTRUCCIONES ANTES DE INTENTAR MONTAR U OPERAR ESTE PRODUCTO. Requiere montaje de adultos. Mantenga los tornillos y las piezas fuera del alcance de los niños. INSTALADOR: Deje este manual con el consumidor. CONSUMIDOR: Conserve este manual para futuras consultas.
Este manual de instrucciones contiene importante información necesaria para el correcto ensamblaje y uso seguro del aparato. Lea y siga todas las advertencias e instrucciones antes de armar y usar el aparato. Siga todas las advertencias e instrucciones cuando use el aparato. Guarde este manual para referencia futura. SÍMBOLOS DE SEGURIDAD Siempre se deben observar las precauciones básicas de seguridad al usar este aparato.
ÍNDICE Advertencias 2, 4-7 Diagrama de piezas y lista de piezas 8 Hardware 9 Instrucciones de montaje 9-12 Instrucciones de funcionamiento 13-15 Cuidado y mantenimiento 15 Resolución de problemas 16 Información de garantía 17 ADVERTENCIA No coloque una olla de cocción vacía sobre el electrodoméstico ni permita que una olla llena hierva en seco mientras el electrodoméstico está en funcionamiento.
ADVERTENCIAS GUARDE ESTAS INSTRUCCIONES • ESTE APARATO SÓLO ESTÁ DISEÑADO PARA CALENTAR EL AGUA. . . NO USAR ACEITE NI GRASA. • La instalación debe cumplir con los códigos locales o, en ausencia de códigos locales, con el Código Nacional de Gas Combustible, ANSI Z223.1/NFPA 54, Almacenamiento y Manipulación de Gases de Petróleo Licuado, ANSI/NFPA 58; o Código de instalación de gas natural y propano, CSA B149.1; Almacenamiento y manipulación de propano, CSA B149.2.
lococookers.com Altura • Nunca deje caer alimentos o accesorios en el líquido de cocción caliente. Baje los alimentos y los accesorios lentamente en el líquido de cocción para evitar salpicaduras o desbordamientos. Al retirar los alimentos del aparato, se debe tener cuidado para evitar quemaduras por los líquidos de cocción calientes. Una vez que la comida se retira de la olla, no permita que la olla hierva en seco.
ADVERTENCIAS: TANQUE LP PELIGRO 1. No almacene un cilindro de gas LP de repuesto debajo o cerca de este aparato. 2. NUNCA llene el cilindro más allá del 80 % de su capacidad. 3. Si las instrucciones en 1 y 2 no se siguen exactamente, puede producirse un incendio que causa lesiones graves o la muerte. 4. La válvula de liberación de seguridad en el tanque LP podría activar la fuga de gas y causar un incendio severo y aumentar el riesgo de lesiones graves o la muerte. 5.
ADVERTENCIAS: TANQUE LP LLENADO DE TANQUES LP: • Use solo distribuidores autorizados y con experiencia. • El distribuidor de LP debe purgar los tanques antes de llenarlos. • El concesionario NUNCA debe llenar el tanque de LP más del 80 % del volumen del mismo. El volumen de propano en los tanques variará según la temperatura. • Un regulador congelado indica un sobrellenado de gas. Cierre de inmediato la válvula del tanque de LP y llame al distribuidor de gas LP para obtener ayuda.
DIAGRAMA DE LAS PIEZAS NOTA: Lave todas las piezas que entrarán en contacto con los alimentos con agua jabonosa tibia. Enjuague y seque con una toalla. 2 1 4 5 3 8 6 9 12 10 7 Pieza n°. 1 2 3 4 5 6 Descripción Canasta Twist & DrainTM/Twist & Steam® Tapa con gancho de agarre Olla de cocción Conjunto de quemador/regulador/manguera Electrodo SureSparkTM Base del hervidor 11 Cant. 1 1 1 1 1 1 Pieza n°.
INSTRUCCIONES DE MONTAJE Herramientas necesarias: Destornillador Phillips • Llave ajustable (no incluidos) Accesorios de montaje 8 B Arandela M6 8 C Tornillo M6x22 A Tornillo M6x14 1 No apriete completamente los tornillos en este momento. 2 D Tornillo M5x10 2 4 Tubo venturi A 6 A Electrodo en la ranura. x4 B B x4 A B Asegúrese de que el tubo venturi salga del lado de la base con dos agujeros. 2 Apriete completamente los tornillos. A B 7 A x2 B x2 lococookers.
INSTRUCCIONES DE MONTAJE 3 A x2 B x2 C D 10 C x2 B A B D A D 11 x2 Apriete completamente los cuatro tornillos del conjunto del quemador del paso 1 después de instalar el protector venturi. Inserte el cable del electrodo a través del orificio en el protector venturi.
INSTRUCCIONES DE MONTAJE 4 Enchufe el cable del electrodo en la parte posterior del encendedor. 5 9 Desenrosque el botón del encendedor e inserte el extremo negativo de la batería AA (–) primero. lococookers.
INSTRUCCIONES DE MONTAJE 6 2 1 TWIST & DRAINTM 1. Levante la canasta sobre la olla. 2. Gire la canasta 90 grados. 3. Bájela de modo que las pestañas inferiores de la canasta descansen sobre las pestañas dentro de la olla para drenar. 1 3 DETERMINAR EL NIVEL MÁXIMO DE LLENADO CUANDO SE UTILIZA UN RECIPIENTE SIN UNA LÍNEA DE LLENADO MÁXIMO: 1. Coloque su comida en la canasta. 2. Coloque la canasta y la comida en el recipiente de cocción vacío. 3.
INSTRUCCIONES DE FUNCIONAMIENTO CONEXIÓN DEL REGULADOR AL TANQUE LP: 1. Coloque el tanque LP en una superficie segura, nivelada y estable. 2. Gire la perilla de control del regulador a la posición OFF (apagado) girándola en sentido antihorario hasta el tope completo. 3. Apague el tanque LP girando la rueda manual en sentido horario hasta el tope completo. 4. Retire la tapa protectora del tanque LP. Use siempre la tapa y la tira provista con la válvula. NO utilice una tapa de transporte POL.
INSTRUCCIONES DE FUNCIONAMIENTO 3. Asegúrese de que un mínimo de 24 pulgadas (61 cm) separe el tanque de LP y el aparato. PRECAUCIÓN La manguera de LP representa un peligro de tropiezo. Se debe tener especial cuidado cuando esté cerca. Si no se produce el encendido en 5 segundos, apague la perilla de control del regulador, espere 5 minutos y luego repita el procedimiento de encendido.
INSTRUCCIONES DE FUNCIONAMIENTO 2. Apague el tanque LP girando la rueda manual en sentido horario hasta el tope completo. 3. Gire la tuerca de acoplamiento en sentido antihorario para aflojar el conector. Afloje solo a mano. NO utilice herramientas. 4. Cuando está desconectado, el regulador debe colgarse del gancho conectado al aparato.
RESOLUCIÓN DE PROBLEMAS PROBLEMA El quemador no se enciende. CAUSA POSIBLE Mala conexión entre el regulador y el tanque LP. El tanque LP está vacío. El botón de encendido no se mantuvo presionado. La batería no está instalada correctamente. Batería baja o agotada. La tapa de la batería no está instalada correctamente. El quemador no permanece encendido. Condiciones de viento excesivas. El tanque LP está vacío. El agua no alcanza la temperatura de cocción deseada.
INFORMACIÓN DE GARANTÍA El aparato ha sido fabricado bajo los más altos estándares de calidad y mano de obra. Garantizamos al consumidor/comprador original que todos los aspectos de este producto estarán libres de defectos materiales y de mano de obra por un (1) año a partir de la fecha de compra. Se proporcionará un reemplazo para cualquier pieza defectuosa sin cargo para la instalación por parte del consumidor.
LoCo - Crazy Good Cookers, LLC. 506 Manchester Expressway • Suite A2 • Columbus, Georgia 31904 800-391-0436 • Correo electrónico: customerservice@lococookers.com Conéctese con nosotros en @lococookers • lococookers.