Specification

ManualsBrandsLoctite ManualsBuilding materials12 fl. oz. Tite Foam Window and Door Insulating Spray Foam (12-Pack)

Loctite® TITE FOAM

Insulating Foam Sealant

Page 1 of 4

Description: Loctite TITE FOAM is a new generation of polyurethane-based insulating foam sealant that

expands to fill, seal and insulate gaps & cracks inside or out. It is a white polymer foam based on purified

& concentrated ingredients that provides 4x more density vs conventional foams for better durability &

insulation. It is easy to use and apply with its attached straw applicator and provides a quick durable seal

from the elements. Loctite TITE FOAM Insulating Foam Sealant has excellent adhesion on most building

materials like wood, concrete, stone, metal etc. Product does not contain CFC-propellants.

Available As:

Item #

Size

Color

1988753

12 fl oz (340 g)

White

Features & Benefits:

 4x more density vs conventional foams for better durability & insulation

 Seals out drafts, moisture and pests

 UV resistance reduces foam brittleness and darkening*

 Strong adhesion while providing flexibility to move with building materials

 Applies soft and cures rigid with a bright white color

 Indoor & outdoor safe

 Tack Free in 8 minutes, Trims in 50-70 minutes

 Sandable & Paintable

Recommended For:

Loctite TITE FOAM is suitable for interior and exterior projects. It has excellent adhesion to most building materials including

wood, metal, stone, brick and PVC. Use for filling gaps and cracks and sealing around wiring and plumbing penetrations, HVAC

ductwork, basement and crawlspace drafts, sill plate & rim joists, attic hatches, under baseboards, gas line penetrations and

outside water faucets. Can also be used to sealing out drafts and moisture as well as keeping out pests and bugs.

For Best Results:

 TITE FOAM is not a fire stopping material and SHOULD NOT be used in areas that require fireproof or fire stopping materials

 Despite significantly higher UV resistance, it is still recommended to protect the foam from UV radiation. Exposed foam

should be coated with a protective covering or coating

 Do not store product on its side

 Does not bond polyethylene, polytetrafluoroethylene (PTFE)/Teflon® or siliconized surfaces

 For cold weather application, product should be stored at room temperature at least 12 hours before application

 In dry conditions, it is recommended to fill gaps in several layers by application of smaller foam strings (up to 2 inches

thickness)

Coverage:

For a 12 oz (340 g) can:

 A 3/8” (9.5 mm) bead size will deliver approximately 134 ft (41.1 m) of foam

Note: Yields shown are based on theoretical calculations, for comparison purposes, and will vary depending on ambient

conditions and particular application.

TITE FOAM

Insulating Foam Sealant

Summary of content (4 pages)

PAGE 1
TITE FOAM Insulating Foam Sealant Description: Loctite TITE FOAM is a new generation of polyurethane-based insulating foam sealant that expands to fill, seal and insulate gaps & cracks inside or out. It is a white polymer foam based on purified & concentrated ingredients that provides 4x more density vs conventional foams for better durability & insulation. It is easy to use and apply with its attached straw applicator and provides a quick durable seal from the elements.
PAGE 2
Typical Uncured Physical Properties: Color: White Appearance: Polymer foam Base: Single component polyurethane Odor: Slightly, of ether Specific Gravity: 1.107 Flash Point: <20°C (<68°F) VOC Content: 19.28% by weight CARB 208.
PAGE 3
Application: Holding can upside down, press the trigger which controls outflow rate of the foam. Dispense the foam sparingly, filling the joint initially by half to avoid excessive overflows. Shake can regularly during use. Slight misting with water can speed cure. Foam can be trimmed with a knife after an hour. Foam will be fully cured in approximately 24 hours. It is recommended foam be protected from UV radiation by a protective covering or coating such as paint, plaster, mortar, etc.
PAGE 4
Trusted Performance. Proven Results. For over 50 years, Loctite Brand adhesives and sealants have taken on the toughest jobs. Used in race cars, airplanes, and even in the space-shuttle, Loctite provides solutions for the most demanding industrial, professional and consumer applications. Loctite gives you not the specialization, power and performance to not only get your job done, but to get it done right. 1-800-624-7767 – Mon-Fri - 9:00a – 4:00p ET www.loctiteproducts.