Camping Equipment User Manual

ManualsBrandsLoctite ManualsCamping EquipmentHYSOL P/N 98036

OPERATION MANUAL

EQUIPMENT

Hysol 175-AIR

N 98036

P/N 98040



Loctite is a trademark of Loctite Corporation, U.S.A. Data in the manual is subject to change without notice.

Loctite Brazil

Av. Prof. Vernon Krieble, 91

06690-11-Itapevi

São Paulo-Brazil

Loctite America

1001 Trout Brook Crossing

Rocky Hill, CT 06067-3910

Loctite Canada Inc.

2225 Meadowpine Boulevard

Mississauga, Ontario L5N 7P2

Loctite Company de México, S.A.d e C.V.

Calzada de la Viga s/n, Fracc. Los Laureles

Loc. Tulpetlac, C.P. 55090

Ecatepac de Morelos, Edo. de México,

México

www.loctite.com

A Company

Hysol 175-AIR-

Summary of content (12 pages)

PAGE 1
 EQUIPMENT OPERATION MANUAL Hysol® 175-AIR P/N 98036 Hysol® 175-AIR-HT P/N 98040 Loctite Americas 1001 Trout Brook Crossing Rocky Hill, CT 06067-3910 Loctite Canada Inc. 2225 Meadowpine Boulevard Mississauga, Ontario L5N 7P2 Loctite Brazil Av. Prof. Vernon Krieble, 91 06690-11-Itapevi São Paulo-Brazil Loctite is a trademark of Loctite Corporation, U.S.A.  Copyright 2001. Loctite Corporation. All rights reserved. Loctite Company de México, S.A.d e C.V. Calzada de la Viga s/n, Fracc.
PAGE 2
Contents 1. 1.1. 1.2. Please Observe the Following................................................................................... 2 Safety .......................................................................................................................... 2 Items supplied.............................................................................................................. 2 2. Description....................................................................................................
PAGE 3
1. Please Observe the Following 1.1.Safety Do not touch the nozzle or molten adhesive with bare skin as they are hot - the operating temperature of the Loctite® Hysol® 175-AIR and 175-AIR-HT applicators is approximately 400ºF (200ºC). Protective gloves should always be worn. Careless handling can cause skin burns. If molten adhesive comes into contact with the skin immerse the affected area immediately in plenty of cold water. Seek medical advice if necessary.
PAGE 4
3. Technical Data Dimensions (L x H x W): Diameter of adhesive inlet: approx. 11 13/16” x 9 15/32” x 2 17/32” (Approx. 300 x 240 x 65 mm) approx. 3 lbs. (1.4 Kg) 10 ft (3 m) long 110-120 VAC 50/60Hz 500W 10 minutes 175-AIR approx. 383°F (195°C) 175-AIR-HT approx. 400°F (204°C) 1 11/16” (43 mm) Extension cable: Wire cross section: max. 65ft (20 m) long at least 16 a.w.g. (1.
PAGE 5
. Operation Normal use: • Fit the stand and place the applicator in an upright position on a flat surface. • Plug the applicator into the power supply socket, and switch on the power. Wait 10 minutes for the applicator to reach its normal operating temperature. • Squeeze the trigger to advance the piston and extrude molten adhesive through the nozzle. • To stop extruding adhesive simply release the trigger. During use, the piston will advance into the barrel as the trigger is pulled.
PAGE 6
. Application Hints As with all adhesives, performance depends on conditions of use. Suggestions or recommendations contained herein are for guidance only, since actual conditions of use are outside the supplier’s control. • • • • • • • • • Ensure that the surfaces to be bonded are dry, free from dust, grease, and loose particles. Apply adhesive to one surface only. Bring the two surfaces together immediately, quickly making any further adjustments.
PAGE 7
FOR ANY REPAIRS OR ADJUSTMENTS – OTHER THAN THOSE DETAILED IN THIS MANUAL – PLEASE CONTACT 1-800-LOCTITE. 8. Care and Maintenance Every attempt has been made to make this exceptionally powerful tool both reliable and trouble-free. However the following precautions should be noted: • Make sure that the applicator is up to temperature before attempting to operate. • Do not leave the applicator switched on for long periods without use.
PAGE 8
Qty 1 - Washer, flat nylon, item 40 Qty 6 – Casing screws, item 34 Page 7
PAGE 9
Trigger Valve Kit Qty 1 – Polytube, item 19 Qty 1 - Trigger Valve Assembly, item 14 Qty 1 – Philips Pan Head Screw, item 33 985230 U.S. Cord Set Assembly Qty 1 – Cordset, item 17 Qty 1 – Clamp, item 18 Qty 2 – Screws, item 38 985231 Accessories Part Number Nozzle 1-Hole Kit, Qty 5, 0.080” (2 mm) orifice 985225 Nozzle 2-Hole 985110 Nozzle 3-Hole 985111 Extension Nozzle 0.120” (3 mm) 985112 Needle Extension Nozzle 0.050” (1.3 mm) 985113 Spreader Extension Nozzle 0.
PAGE 10
11. Appendix. Pictures of available nozzles/accessories.
PAGE 11
12. Exploded View.
PAGE 12
13. Parts List. 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM 1 1 1 1 2 1 2 2 3 4 1 6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 2 1 1 QTY.