Manual

ManualsBrandsLodar ManualsReceivers and Amplifiers6 Function FET Receiver with master output and IP Stainless Transmitter

Secure using 5mm (3/16") bolts (not supplied)

through the 4 mounting feet

TAKE TIME TO LOCATE THE BEST POSITION

If necessary, power the Receiver and move it around

the vehicle until the required performance is achieved.

Operate the Transmitter and observe the Receiver

internal LED’s.

Mount as HIGH as possible

AVOID surfaces with HEAVY VIBRATION

AVOID DIRECT SPRAY from wheels

In a HOT CLIMATE fit in a SHADED position

Cable gland should face DOWN or BACK

Receiver 9206RX and 9306RX shown,

Waterproof to IP67, complete with 3 metres (10 ft) cables

CAUTION

MOUNT RECEIVER

or Disconnect Battery

IDENTIFY POWER

CONNECTION POINT

AND ISOLATE SUPPLY

Fuse

Remove fuse

Vehicle batteries contain gasses

which are flammable and explosive.

Wear eye protection and do not lean

over battery while disconnecting. Do

not wear metal jewellery.

WARNING

POSITIVE

NEGATIVE

92106RX.01E

7 core cable.

These are

Power Outputs

Transmitter Function I.D.

2 core cable.

These are

Power Inputs

1. The Receiver is designed to carry a maximum of 15 Amps. That is, for example,15 Amps

through one output or 5 Amps each through 3 outputs.

2. Master Output. This can be configured to Continuous or Parallel operation, see overleaf for

details.

3. If Receiver outputs are connected in parallel with an external switching device (wired remote)

the Receiver will instantly switch off when the wired remote is operated

4. Lodar Receivers have an isolation switch for safety, to allow for registering a MUST

replacement Transmitter.

5. Safety Feature. Both the Transmitter and the Receiver will “time out” after 30 minutes of

inactivity. This can be altered, ask your dealer.

BEFORE YOU START

Wiring Instructions for 92 Series & 93 Series 6 Function Receivers

CONNECT

WIRES

or re-connect Battery

ACTIVATE THE

RECEIVER SUPPLY

Fuse

Replace fuse

Press the Transmitter buttonRESET

to activate the system, and carefully

test each function for correct operation.7

TEST

CONNECT TRANSMITTER BATTERY

Batteries generally have to be

disconnected when shipping.

BLACK

RED

GREEN

YELLOW

BROWN

BLUE

WHITE

Output Function 1

Output Function 2

Output Function 3

Output Function 4

Output Function Master

7 Core wire used for:-

Wire Colour

Make notes about the connections made in the boxes

What is the MASTER Output for ?

It is used to operate the pump of an electro-hydraulic

power pack or maybe a clutch pump. It can also be

used for powering a dump valve, master valve etc.

It can be configured to work continuously, that is ON

when SET is pressed and OFF when STOP is

pressed; or in parallel with any output, that is, it is

active only a function is operated. If it is needed with

certain functions only, this can easily be configured.

Output Function 5

Output Function 6

12/24 Volts DC Nominal

Positive Supply

RED

Negative

BLACK

2 Core wire used for:-

Wire Colour

Shown with optional Keypad

Summary of content (2 pages)

PAGE 1
Wiring Instructions for 92 Series & 93 Series 6 Function Receivers 92106RX.01E 1 ! 2 IDENTIFY POWER CONNECTION POINT AND ISOLATE SUPPLY BEFORE YOU START Remove fuse Fuse 1. The Receiver is designed to carry a maximum of 15 Amps. That is, for example,15 Amps through one output or 5 Amps each through 3 outputs. 2. Master Output. This can be configured to Continuous or Parallel operation, see overleaf for details. 3.
PAGE 2
92106RX.01E Component Detail LED marked “SET” LED’s marked “F1 - F2 - F3 - F4 - F5 - F6 and M” When ON indicate an output to that function Indicates system is active LED marked “FAULT” Indicates an overload is present; the System cannot be RESET until overload is removed. This LED blinks for 20 seconds when the Receiver is initially powered. A replacement Transmitter has to be registered during this 20 second period.