Operation Manual

Individual 40-55
User guide
27

Initial installation
Setting options for the satellite system
(max. 4 satellites on DiSEqC multiswitch):
 Select and adapt settings for the DiSEqC
multiswitch.
OK Adopt settings.
Repeat rate The refresh rate determines how often a DiSEqC
command is output. A refresh is only necessary with
cascaded systems.
Control
voltage
The control voltage controls the switching of the
polarisation level (horizontal/vertical) in non-DiSEqC
capable components (e.g., control of single LNBs via
DiSEqC multiswitch).
22kHz signal The 22 kHz signal controls the switching between
high and low band in the Band setting. The Position
setting controls the selection of the satellites in non-
DiSEqC capable components.
Toneburst The Toneburst controls the selection of the satellites
in non-DiSEqC but Toneburst capable components
with the Position and Option settings.
 Proceed to next step.
 Mark Satellite 1 ... Satellite 4,
 Select satellite.
OK Adopt settings.
 Proceed to next step.
With the refresh rate you determine how often a DiSEqC command is output. This is only
necessary in a cascaded system. Your system provider will bei able to tell you more about
this.
Settings DiSEqC multiple switch
Back with Proceed with
Repeat rate none 1 2
Control voltage 13 / 18V off on
22kHz signal Band Position off
Toneburst off Position Option
DiSEqC
multiple
switch
Thor/Intelsat10-02 0,8
Eutelsat 5 West A 5°W
Nilesat 7°W
Eutelsat 7 West A 7,2°W
Eutelsat 8 West A 8°W
Eutelsat 12 West A 12,5°W
Telestart12 12,5°W
ASTRA3 23,5°E
ASTRA1 19,2°E
Eutelsat 16A 16°E
Hot Bird 13°E
Eurobird 9A 9°E
Eurobird 7A 7°E
ASTRA4A 4,8°E
Select satellites
Please select satellite 1 to satellite 4.
Note: The newly selected parameter must be confirmed with the button.
Back with Proceed with
OK
none
Optus D1160°E
Türksat 42°E
Hellas Sat2 39°E
Eutelsat 36A 36°E
Eutelsat 28A 28,5°E
ASTRA2 28,2°E
Satellit 1 Satellit 2 Satellit 3 Satellit 4
Satellite
selection
.
 Set LNB frequencies.
Normally, you do not need to change the values.
OK Adopt settings.
 Proceed to next step.
Proceed with Setting options for DVB-S reception
(continued).
.
LNB frequencies
Please select the LNB frequencies for both High and Low Bands.
Note: The newly selected parameter in each case must be confirmed with the button.
ASTRA1 19,2°E low band 9750 MHz 10000 MHz 10200 MHz 10600 MHz
ASTRA1 19,2°E high band 10600 MHz 10750 MHz 11000 MHz 11250 MHz
Hot Bird 13°E low band 9750 MHz 10000 MHz 10200 MHz 10600 MHz
Hot Bird 13°E high band 10600 MHz 10750 MHz 11000 MHz 11250 MHz
Eutelsat W2 16°E low band 9750 MHz 10000 MHz 10200 MHz 10600 MHz
Eutelsat W2 16°E high band 10600 MHz 10750 MHz 11000 MHz 11250 MHz
Türksat 42°E low band 9750 MHz 10000 MHz 10200 MHz 10600 MHz
Türksat 42°E high band 10600 MHz 10750 MHz 11000 MHz 11250 MHz
OK
Back with Proceed with
LNC
frequencies