ViewVision DR+ DVD Operating Manual
Table Of Contents
- Remote control Assist – recorder operation
- Front Panel
- Rear Panel & Display
- Welcome
- For your safety
- Essential Information
- Initial Installation
- Initial Remote Control Setup
- Resetting the DVD Recorder
- Switching over to Progressive Scan
- Connections - General
- Connecting to the Aerial
- Connecting to the Television
- Connecting to a set-top box / Satellite Receiver
- Connecting to an External Decoder Box
- Connecting to an Amplifier
- Connecting Audio/Video (A/V) Accessories
- Connecting a digital camcorder
- Activating Digital Link
- Basic Settings
- Main menu
- Setup menu
- The General Menu
- Language Menu
- Audio Menu
- Lock Menu
- Recording Menu
- Disc Menu
- Additional Screen Menus
- HDMI mode
- Video mode
- DivX mode
- Audio mode
- Photo mode
- Card-Reader mode
- Remote control Assist – Card-Reader operation
- Recording
- Edit recordings
- Menu Title List and Chapter List
- Edit Original and Playlist
- Add chapter markers
- Create new Playlist
- Add title/chapter to the Playlist
- Delete title/chapter from Original/Playlist
- Delete part
- Title Name
- Select title start point
- Select chapter
- Sorting
- Undo/redo deletion
- Combine titles
- Divide title
- Combine chapters
- Move Playlists Chapters
- Hide title/chapter
- Protect title
- Dubbing
- Troubleshooting
- Technical Specifications
- Operating additional devices
- Remote control Assist – TV-operation
- Language Code List
- List of country codes
- Glossary
- Index
- Service
45 -
Recording
Digital camcorders can usually record audio as 16 bit/48 kHz stereo or twin
stereo tracks with 12 bit/32 kHz. This recorder can only record one stereo audio
track. Set “DV Rec Audio“ as required or Audio 1 or Audio 2 (page 25).
The sampling rate of the digital sound input to the DV IN socket must be either
32 or 48 kHz (not 44.1 kHz).
Recording may suffer from interference if the camcorder stops playing back, if a
part of the tape that has not been recorded on is played back, if the electricity
supply to the camcorder is cut off, or if the DV cable comes out.
When “DV Rec Audio“ is set to “Audio 2“ and there is no Audio 2 signal, “DV
Audio“ will automatically be set to “Audio 1“.
DV messages
When you are using the DV IN socket, the following messages may appear on
the screen.
Not connected to camcorder: The camcorder is not properly connected, or
the camcorder is switched off.
Too many devices connected: This recorder‘s DV socket only supports the
connection of one camcorder.
Check tape: There is no tape in the device that is connected.
Incompatible device: The recorder is unable to control the camcorder.
Information is being reloaded: The camcorder is updating data for DV.
Camera mode: The camcorder is set to camera mode.
Troubleshooting
If you are not receiving images and/or sound via the DV IN socket, check the
following:
The DV cable must be properly connected.
Switch off the camcorder that is connected, and switch it back on.
Tune the audio input in to the recorder.
➠ This recorder cannot necessarily control every camcorder that is connected to it.
•
•
•
•
•
•
•
Recording from a digital camcorder
You can record from a camcorder that is connected to the DV IN socket in the
recorder‘s front panel. You can use the recorder‘s remote to control a cam-corder
and the recorder. Before recording, make sure that the audio input has been set
up for the DV IN socket (page 25).
The digital camcorder must be connected to the DV IN socket at
the front of the housing. Further information can be found on
page15.
You can choose from between Audio 1 (original audio) and Audio
2 (overdubbed audio).
The DV input is set using the “DV Rec Audio“ submenu of the
main menu (page 25).
Select DV input.
“DV” is displayed in the display window of the recorder and on
the screen.
Search the position on the camcorder tape from which you want
to record.
For optimum results, interrupt play-back of the camcorder at the
point from which you want to record. Depending on the
camcorder you can operate the functions STOP, PLAY and PAUSE
with this recorder.
Start recording.
The recording is stopped automatically when the recorder detects
no signal.
Interrupt recording. Press again to continue.
End recording.
➠ You cannot use the recorder to control the camcorder while
recording is in progress.
➠ In Video mode, the last frame of the recording is shown on
the screen for a short time after recording has ended.
➠ For timer recordings to work properly on this recorder, the
digital camcorder should be switched on and operational.