ViewVision DR+ DVD Operating Manual
Table Of Contents
- Remote control Assist – recorder operation
- Front Panel
- Rear Panel & Display
- Welcome
- For your safety
- Essential Information
- Initial Installation
- Initial Remote Control Setup
- Resetting the DVD Recorder
- Switching over to Progressive Scan
- Connections - General
- Connecting to the Aerial
- Connecting to the Television
- Connecting to a set-top box / Satellite Receiver
- Connecting to an External Decoder Box
- Connecting to an Amplifier
- Connecting Audio/Video (A/V) Accessories
- Connecting a digital camcorder
- Activating Digital Link
- Basic Settings
- Main menu
- Setup menu
- The General Menu
- Language Menu
- Audio Menu
- Lock Menu
- Recording Menu
- Disc Menu
- Additional Screen Menus
- HDMI mode
- Video mode
- DivX mode
- Audio mode
- Photo mode
- Card-Reader mode
- Remote control Assist – Card-Reader operation
- Recording
- Edit recordings
- Menu Title List and Chapter List
- Edit Original and Playlist
- Add chapter markers
- Create new Playlist
- Add title/chapter to the Playlist
- Delete title/chapter from Original/Playlist
- Delete part
- Title Name
- Select title start point
- Select chapter
- Sorting
- Undo/redo deletion
- Combine titles
- Divide title
- Combine chapters
- Move Playlists Chapters
- Hide title/chapter
- Protect title
- Dubbing
- Troubleshooting
- Technical Specifications
- Operating additional devices
- Remote control Assist – TV-operation
- Language Code List
- List of country codes
- Glossary
- Index
- Service
57 -
Troubleshooting
Problem Possible cause Remedy
No function. The mains cable is not plugged in. Fix the mains cable firmly into a socket.
No image. The television is not switched to re-
ceive signals from the Recorder.
Select the right video input mode on the television, so that
the image from the Recorder appears on the television
screen.
The SCART cable is not properly connected. Connect the SCART cable properly.
The television that is connected is switched off. Switch the television on.
No sound. The connected audio equipment is
not switched to DVD playback.
Set the audio receiver so that you can hear the sound playing
on your Recorder.
The audio cables are not properly connected. Connect the audio cable properly.
The connected audio equipment is switched off. Switch on the audio equipment that is connected.
The audio connection cable is faulty. Change it.
Inferior picture quality. The disc is dirty. Clean the disc.
Playback not possible. There is no disc. Insert a disc. (Check that the disc display
comes on in the display window.)
A non-playable disc has been inserted. Insert a playable disc. (Check the disc type, the colour system
and the region code.)
The disc has not been inserted with the playable
side downwards.
Insert the disc with the playable side downwards.
The disc has not been properly placed in the guide. Position the disc properly into the guide in the disc drawer.
The disc is dirty. Clean the disc.
A security rating has been set. Cancel the security rating or change the protection.
There is interference with images from an
external source.
The video signal from the external component is
copy-protected.
You cannot get a connection from this recorder. Connect the
component directly into the television.
A channel is skipped when using P+ / P- . The channels have not been saved in the recorder. Retune the channels. See channel tuning on page 18.
The image or sound on the transmission channel
is weak or absent.
Loose antenna or cable. Tighten the connections or change the cable.
The camcorder image is not displaying. The camcorder is switched off. Switch on the camcorder and make sure your are using it
properly.
The camcorder image is not appearing on the
television screen when using the A/V input or
DV IN to the Recorder.
The Recorder AV selection is wrong. Select the input channel (AV1, AV2, DV etc.) with DVD-AV.
A disc that was recorded to from this Recorder
cannot be played on a different DVD player.
The disc was recorded in video mode. Finalising the disc (page 26).