User's Guide

ManualsBrandsLogia ManualsElectronicsWireless Weather Sensor (915MHz Transmitter)

SET UP WI-FI CONNECTION

When you rst power up the console, or press and hold the SENSOR/WI-FI button for six (6) seconds,

the console LCD display will show the letters “AP” and an icon to signify that it has entered

Access Point (AP) mode. At this time it will be ready for the WI-FI settings to be adjusted.

Use your smartphone, tablet, or computer to connect to the console via WI-FI by following these steps:

1. On PC, open your WI-FI network settings. On Android

™

or iOS devices, go to settings menu

and then select Connections/WI-FI to open the network settings.

2. Locate the display console’s SSID from the list. It should appear as PWS-XXXXXX (where all

the X’s are integers) in the list. Tap on the SSID to connect. This step will take several seconds.

MAIN CONSOLE

Your main console can pairing up with the wireless 5-in-1 outdoor weather sensor and up to 7

optional wireless hygro-thermo outdoor sensors. (Not included)

Powering up the main console

1. Remove the battery door on the back side of the main unit.

2. Insert 6 new AA batteries and replace the battery door.

3. Once the batteries are inserted, the segments of the LCD will be shown.

NOTE:

If no display appears on the LCD after inserting the batteries, press [ RESET ] key by using a

pointed object.

Pairing of wireless 5-in-1 weather sensor with main console

After insertion of batteries, the main console will automatically search and connect the

wireless 5-in-1 sensor (antenna blinking). Once the connection is successful, antenna mark

and readings for outdoor temperature & humidity, wind speed, wind direction and rainfall will

appear on the display.

Changing batteries and manual pairing of sensor

Whenever you changed the batteries of the wireless 5-in-1 sensor, pairing must be done

manually.

1. Change all the batteries to new ones in the sensor.

2. Press [ CH ] until the

icon appear in the Outdoor section

3. Press [ SENSOR / SYNC ] key.

4. Press [ RESET ] key on the sensor.

NOTE:

Pressing [ RESET ] key at bottom of wireless 5-in-1 sensor will generate a new ID code for

pairing purpose. So you also need to press the [ SENSOR / SYNC ] key on the console to

repairing up the sensor.

Pairing the wireless sensor(s) with the console

The console will automatically search and pair up your wireless sensor(s). You can also press

[SENSOR / SYNC ] key to search the on display channel's sensor manually. Once your sensor

paired up, the sensor signal strength indicator and weather information will appear on your

console display.

SYNC UP PC TIME

This unit is designed to automatically synchronize its calendar and clock when connected to

the computer with PC software "Weather Tool" through USB data cable. Once connected to the

computer, the unit will automatically synchronize the time instantly and 12:00am per day. You

can also press the [ TIME SYNC ] key to sync up PC time instantly.

NOTE:

- The time sync function only work with the PC software "Weather Tool", please make sure the

PC software is open.

- PC Time sync up is according to your current PC time, so please ensure your PC time is

correct. Once the PC time sync up the

icon will appear in the Time section.

- You can also enable or disable auto time sync function by press and hold [ TIME SYNC ] key

for 8 seconds.

4. Jot down your ID and key for the further setup step.

SETUP WI-FI CONNECTION

1. When you rst power up the console, or press and hold the [ WI-FI / SENSOR ] key for 6

seconds in normal mode, the console LCD will show "AP" and "

" icon to signify that it has

entered AP (access point) mode, and is ready for WI-FI settings.

2. Use the smart phone, tablet, or computer to connect to the console through WI-FI.

3. In PC choose WiFi network settings or In Android / iOS choose setting → WI-FI to select the

console’s SSID: PWS-XXXXXX in the list and it will need several second to connect.

PWS-XXXXXX

PC WI-FI network interface Android WI-FI network interface

4. Once connected, enter the following IP address into your internet browser’s address bar, to

access the console’s web interface:

http://192.168.1.1

NOTE :

- Some browsers will treat 192.168.1.1 as a search, so make sure you include http:// header.

- Recommended browsers, such as the latest version of Chrome, Safari, Edge, Firefox or

Opera.

4. Jot down your ID and key for the further setup step.

SETUP WI-FI CONNECTION

1. When you rst power up the console, or press and hold the [ WI-FI / SENSOR ] key for 6

seconds in normal mode, the console LCD will show "AP" and "

" icon to signify that it has

entered AP (access point) mode, and is ready for WI-FI settings.

2. Use the smart phone, tablet, or computer to connect to the console through WI-FI.

3. In PC choose WiFi network settings or In Android / iOS choose setting → WI-FI to select the

console’s SSID: PWS-XXXXXX in the list and it will need several second to connect.

PWS-XXXXXX

PC WI-FI network interface Android WI-FI network interface

4. Once connected, enter the following IP address into your internet browser’s address bar, to

access the console’s web interface:

http://192.168.1.1

NOTE :

- Some browsers will treat 192.168.1.1 as a search, so make sure you include http:// header.

- Recommended browsers, such as the latest version of Chrome, Safari, Edge, Firefox or

Opera.

4. Jot down your ID and key for the further setup step.

SETUP WI-FI CONNECTION

1. When you rst power up the console, or press and hold the [ WI-FI / SENSOR ] key for 6

seconds in normal mode, the console LCD will show "AP" and "

" icon to signify that it has

entered AP (access point) mode, and is ready for WI-FI settings.

2. Use the smart phone, tablet, or computer to connect to the console through WI-FI.

3. In PC choose WiFi network settings or In Android / iOS choose setting → WI-FI to select the

console’s SSID: PWS-XXXXXX in the list and it will need several second to connect.

PWS-XXXXXX

PC WI-FI network interface Android WI-FI network interface

4. Once connected, enter the following IP address into your internet browser’s address bar, to

access the console’s web interface:

http://192.168.1.1

NOTE :

- Some browsers will treat 192.168.1.1 as a search, so make sure you include http:// header.

- Recommended browsers, such as the latest version of Chrome, Safari, Edge, Firefox or

Opera.