Fieldbook E1 User’s Guide
F i e l d b o o k E 1 U s e r ’ s G u i d e Safety Information 1. Please read these safety instructions carefully. 2. Please keep this User’s Guide for later reference. 3. Please disconnect this device from the power source before cleaning. Do not use liquid or detergent for cleaning. Use a moist sheet or cloth for cleaning. 4. Make sure the device is connected to a power source with the correct voltage, frequency, and ampere. 5.
F i e l d b o o k E 1 U s e r ’ s G u i d e 9. Caution on the use of the battery: Use only the battery recommended by the manufacturer or the same type of battery installed by the manufacturer. Incorrect battery may cause explosion or fire hazard. Recycle or discard used batteries according to the manufacturer’s instruction or your local authorities. 10. The device uses nonvolatile memory that requires a battery to retain system information when power is removed.
F i e l d b o o k E 1 U s e r ’ s G u i d e FCC Compliance Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
F i e l d b o o k E 1 U s e r ’ s G u i d e FCC RF Radiation Exposure Statement: 1. This transmitter has demonstrated co-location compliance requirements with Wi-Fi, Bluetooth and RFID Modules. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
F i e l d b o o k E 1 U s e r ’ s G u i d e Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC and EMC directive 2004/108/EC.
F i e l d b o o k E 1 U s e r ’ s G u i d e This device is a 2.
F i e l d b o o k E 1 U s e r ’ s G u i d e Table of Contents CHAPTER 1. GENERAL INFORMATION ................................... 11 1.1. INTRODUCTION .................................................................... 11 1.2. SPECIFICATIONS .................................................................. 12 1.2.1. Main System ............................................................... 13 1.2.2. Interfaces ..................................................................
F i e l d b o o k E 1 U s e r ’ s G u i d e Fieldbook AC Adapter ................................................................................. 32 2.2.3. Insert a SIM Card ........................................................ 34 2.2.4. Insert a Micro SD Card ................................................ 36 2.2.5. Restore Factory Settings ............................................. 38 2.2.6. Turn On the Device ..................................................... 39 2.
F i e l d b o o k E 1 U s e r ’ s G u i d e WiFi/WWAN/Bluetooth/GPS........................................................................ 56 3.4. ADMINISTRATOR MENU ........................................................ 58 3.4.1. Accessing the Administrator Menu .............................. 58 3.4.2. Resetting the Password .............................................. 59 3.5. ADMINISTRATOR SETTINGS .................................................. 60 3.5.1.
F i e l d b o o k E 1 U s e r ’ s G u i d e 6.2. MAINTAINING THE LCD DISPLAY .......................................... 77 6.3. CLEANING THE FIELDBOOK E1 ............................................. 77 CHAPTER 7. 10 TROUBLESHOOTING ..........................................
F i e l d b o o k E 1 U s e r ’ s G u i d e Chapter 1. General Information 1.1. Introduction ® The Fieldbook E1 is a rugged tablet based on the TI OMAP platform (OMAP4460). This high-performance tablet features a bright 10.1” ® ® LED-backlit LCD display and runs on Google Android operating system. The Fieldbook E1 has been engineered and tested to meet military (MIL-STD810G) and industrial (IP65) standards.
F i e l d b o o k E 1 U s e r ’ s G u i d e • 5 MP AF rear camera with LED flash Ø Free programmable physical buttons Ø FieldControl dashboard software 1.2. Specifications The Fieldbook E1 is a flexible, multi-functional ultra-slim rugged tablet. The following specifications can be applied in diverse operational environments and implemented in multi-faceted applications.
F i e l d b o o k E 1 U s e r ’ s G u i d e 1.2.1. Main System Operating System Android™ 4.2.2 CPU ® TI OMAP Platform (OMAP4460 dual-core, 1.5GHz) System Memory 1GB LPDDRII memory Storage 1 x 64GB Flash eMMC LCD Panel 10.1” WXGA (1366x768) LED backlight FieldView™ Pro technology (sunlight readable) Touch Panel Audio Two-point capacitive touch screen 1 x High-quality speaker (1W) 1 x Internal microphone (on front bezel) Communication Wi-Fi IEEE 802.11 a/b/g/n Bluetooth 4.
F i e l d b o o k E 1 U s e r ’ s G u i d e 1.2.2. Interfaces External 1 x Micro USB OTG 1 x Audio combo jack 1 x Micro HDMI slot 1 x Micro SD slot 1 x Micro SIM slot (optional) 1 x Docking connector 3 x Pass-through connectors 1 x DC jack 1.2.3.
F i e l d b o o k E 1 U s e r ’ s G u i d e 1.2.4. Power supply Adapter AC to DC, 12VDC@2.1A, 25W AC 90V ~ 243V, 47~63Hz input Battery Internal lithium polymer battery, 10000mAh (minimum: 9600mAh), 3.7V 1.2.5. Environment Operating Temperature Storage Temperature Humidity -20°C to +60°C (MIL-STD-810G Method 501.5 and 502.5) -30°C to +70°C (MIL-STD-810G Method 501.5 and 502.5) 5-95% without condensation (MIL-STD-810G Method 507.
F i e l d b o o k E 1 U s e r ’ s G u i d e 1.2.6. Material Chassis Enclosure Rugged Tablet Form Factor PC/ABS Plastic, PC/ABS and TPU Double Injection with Protective Rubber Grips Set Dimensions (W x H x D mm) 277.5 x 179.7 x 22.4mm (without rubber corner bumper) 283.5x185.7x22~28mm (with rubber corner bumper) Weight Approximate 1.075kg (with internal battery) 1.2.7.
F i e l d b o o k E 1 U s e r ’ s G u i d e 1.2.8. Optional: Internal Module Sierra MC7710 or MC7750 or MC7700 Protocol LTE/HSPA+ (MC7700/7710) LTE/EV-DO (MC7750) Frequency 1. LTE: • 700(B17)/AWS (MC7700) • 800/900/1800/2100/2600 MHz (MC7710) • 700(B13) MHz (MC7750) 2. WCDMA: • 850/1900/2100 MHz (MC7700) • 900/2100 MHz (MC7710) 3. CDMA 1xRTT/EV-DO Rev A: • 800/1900 MHz (MC7750) 4.
F i e l d b o o k E 1 U s e r ’ s G u i d e Barcode Scanner Decoded Mode 1. 1D Symbologies : EAN/UPC, RSS, Code 39, Code 128, UCC/EAN 128, ISBN, ISBT, Interleaved, Matrix, Industrial and Standard 2 of 5, Codabar, Code 93/93i, Code 11, MSI, Plessey, Telepen, postal codes. 2. 2D Symbologies: Data Matrix, PDF417, Micro PDF 417, Maxicode, QR, Aztec, EAN.UCC composite.
F i e l d b o o k E 1 U s e r ’ s G u i d e 1.3.
F i e l d b o o k E 1 U s e r ’ s G u i d e Chapter 2. System Setup 2.1. Exploring your Fieldbook E1 Before starting to set up the Fieldbook E1, familiarize yourself with the controls, connectors and I/O ports, which are illustrated in the figures below. When placed upright, the front panel of the Fieldbook E1 appears as shown in below.
F i e l d b o o k E 1 U s e r ’ s G u i d e 2.1.1. Front View Fieldbook E1 Front View Item 1. 1.2 MP camera Description For capturing photos and videos and for video conferencing. 2. Digital microphone For capturing sound and voice 3. Home button Opens the Home screen. 4. Protective rubber Protects the system from impacts on the corners 5. Power indicator Indicates the current power status 6.
F i e l d b o o k E 1 U s e r ’ s G u i d e Power LED Definitions Green The battery is fully charged. Amber Battery capacity is less than 15%. (Blinking at 1Hz) Amber Battery capacity is less than 8%. (Blinking at 3Hz) Red 22 Battery is charging and not yet full.
F i e l d b o o k E 1 U s e r ’ s G u i d e 2.1.2. Rear View Fieldbook E1 Rear View Item 1. 1D/2D barcode Description Scans barcodes scanner 2. 5MP camera For capturing photos and videos 3.
F i e l d b o o k E 1 U s e r ’ s G u i d e Item 4. Stylus cord hooks Description Secures the stylus cord. Choose the location depending on whether you are left-handed or right-handed. 5. Stylus For entering information or selecting items on the screen.
F i e l d b o o k E 1 U s e r ’ s G u i d e 2.1.3. Left View Fieldbook E1 Left View Item Description 1. 3.5mm headphone Connects an external 3.5mm 4-conductor TRRS jack 2. Battery on/off (stereo-plus-mic) headphone Enables/disables battery power switch 3. Micro USB OTG port Connects USB devices like mouse, keyboard, and others to the device 4. SIM card slot Requires a micro SIM card 5. Power button Turns the device on/off. Resumes the device from standby mode 6.
F i e l d b o o k E 1 U s e r ’ s G u i d e Item 9. Micro HDMI jack Description Supports Full HD video output through a micro HDMI cable 10.
F i e l d b o o k E 1 U s e r ’ s G u i d e 2.1.4. Right View Fieldbook E1 Right View Item 1. DC-jack Description Connects the device to an power adapter to supply continuous power during use and battery recharging. 2. Programmable Allow you to assign specific functions to a button. function buttons The table below shows the default key F1, F2, F3 assignments. 3.
F i e l d b o o k E 1 U s e r ’ s G u i d e Key Mapping 28
F i e l d b o o k E 1 U s e r ’ s G u i d e 2.1.5. Bottom View Fieldbook E1 Bottom View Item Description 1.
F i e l d b o o k E 1 U s e r ’ s G u i d e 2.2. Preparing for Installation The Fieldbook E1 is designed and pre-configured for easy setup and use. This section describes the installation steps you should follow to get the system running as quickly as possible. 2.2.1. Switch ON the Main Battery The internal battery is switched off during transit in order to completely cut off power to the device. To switch on the main battery: 1. Open the I/O ports door. 2.
F i e l d b o o k E 1 U s e r ’ s G u i d e 2.2.2. Connecting a power supply The AC adapter provides power to the system and charges the internal battery at the same time. The AC adapter has an auto-switching design that can connect to any 100VAC ~ 240VAC power outlet. To connect the tablet to a power outlet: 1. Plug the AC adapter connector to the DC-jack socket. Plugging in the AC Adapter Connector 2. Plug the power cord to the AC adapter. 3.
F i e l d b o o k E 1 U s e r ’ s G u i d e WARNING: Before cleaning the system, make sure it is disconnected from any external power source. Fieldbook AC Adapter The Fieldbook AC adapter comes with two types of detachable plugs: a NEMA power plug with two flat parallel blades, and a CEE power plug with two round pins. To remove a power plug: 1. Press the release button. 2. Slide out the power plug to remove.
F i e l d b o o k E 1 U s e r ’ s G u i d e To insert a power plug: 1. Align the power plug sides to the slot on the AC adapter. 2. Slide the power plug all the way into the slot. You will hear a “click” to indicate that the power plug is locked in place.
F i e l d b o o k E 1 U s e r ’ s G u i d e 2.2.3. Insert a SIM Card The SIM card stores your phone number, your contact’s information, and saved messages. NOTE: Internet access may incur fees. Contact your service provider for details. NOTE: This device requires a micro SIM card. WARNING: Remove all power from the device before installing or removing the SIM card. To insert a SIM card: 1. Open the I/O ports door. 2.
F i e l d b o o k E 1 U s e r ’ s G u i d e To remove a SIM card: 1. Open the I/O ports door. 2. Gently push the SIM card. The SIM card is slightly ejected from the SIM card slot. 3. Remove the SIM card.
F i e l d b o o k E 1 U s e r ’ s G u i d e 2.2.4. Insert a Micro SD Card Use a micro SD card to store photos, music, videos and other files. WARNING: Remove all power from the device before installing or removing a micro SD card. To insert a micro SD card: 1. Open the I/O ports door. 2. Insert the micro SD card into the micro SD card slot with the gold contacts facing up. 3. Push the micro SD card all the way until it is flush into the micro SD card slot.
F i e l d b o o k E 1 U s e r ’ s G u i d e To remove a micro SD card: 1. Open the I/O ports door. 2. Gently push the micro SD card. The micro SD is slightly ejected from the slot. 3. Remove the micro SD card.
F i e l d b o o k E 1 U s e r ’ s G u i d e 2.2.5. Restore Factory Settings Restore the device to factory settings before using it. You may also restore factory settings if the device encounters a persistent problem, or if you want to pass the device to someone else. CAUTION: Restoring the device to factory settings deletes data and user-configured settings. Make sure to perform a backup before proceeding. To restore factory settings: 1. Turn off the device. 2.
F i e l d b o o k E 1 U s e r ’ s G u i d e 2.2.6. Turn On the Device To turn the device on: Press the Power button until the home screen is displayed. Turning on the Device To turn the device off: 1. Press the Power button until the power off prompt shows. 2. Tap OK to turn off the device, or tap Cancel to keep the device turned on.
F i e l d b o o k E 1 U s e r ’ s G u i d e 2.3. Android Settings 2.3.1. Setting Up for the First Time The first time you turn on the device, you will be asked to set up your Android system. Follow onscreen instructions to select the language you want to use, enable location-based services, choose how you want to connect to the Internet, and more. NOTE: Internet and location-based services may incur fees. Contact your mobile operator or service provider for details. 2.3.2.
F i e l d b o o k E 1 U s e r ’ s G u i d e Item 4. Flick Description To swipe vertically, but in quicker, lighter strokes to go through a list or browse a long screen. 5. Pinch To use two fingers to zoom in or out of the screen. 2.3.3. Home Screens Choose from five home screens to personalize your Android experience. From the main home screen, swipe to the left or right to choose another home screen and add your favorite widgets, apps, and folders.
F i e l d b o o k E 1 U s e r ’ s G u i d e 2.4. Connect the Fieldbook E1 to Other Devices 2.4.1. Connecting a USB Device Fieldbook E1 comes with a micro USB On The Go (OTG) port, so you can connect other USB devices to it using a micro USB cable. NOTE: The Fieldbook E1 does not come with a micro USB cable. To connect a micro USB device: 1. Open the I/O ports door. 2. Connect the micro USB cable to the micro USB port on the Fieldbook E1. 3.
F i e l d b o o k E 1 U s e r ’ s G u i d e To remove a USB device: CAUTION: If you are removing a storage device, make sure it is safe to disconnect it from the Fieldbook E1 to prevent data loss or damage. 1. Open the I/O ports door. 2. Unplug the micro USB cable from the micro USB port on the Fieldbook E1. 3. Unplug the other end of the micro USB cable from the USB device you connected.
F i e l d b o o k E 1 U s e r ’ s G u i d e 2.4.2. Connecting an HD Display The micro HDMI port connects the Fieldbook E1 to a high-definition display for up to 1080p video output. NOTE: The Fieldbook E1 does not come with a micro HDMI cable. To connect an HD display: 1. Open the I/O ports door. 2. Connect the micro HDMI cable to the micro HDMI port on the Fieldbook E1. 3. Connect the other end of the micro HDMI cable to the HD display you want to connect.
F i e l d b o o k E 1 U s e r ’ s G u i d e To remove an HD display: 1. Open the I/O ports door. 2. Unplug the micro HDMI cable from the micro HDMI port on the Fieldbook E1. 3. Unplug the other end of the micro HDMI cable from the other USB device.
F i e l d b o o k E 1 U s e r ’ s G u i d e 2.4.3. Connecting a Headphone The audio jack connects the Fieldbook E1 to a headphone. NOTE: The Fieldbook E1 does not come with a headphone. To connect a headphone: 1. Open the I/O ports door. 2. Connect the headphone connector to the audio jack on the Fieldbook E1.
F i e l d b o o k E 1 U s e r ’ s G u i d e To remove a headphone: 1. Open the I/O ports door. 2. Unplug the headphone connector from the audio jack on the Fieldbook E1.
F i e l d b o o k E 1 U s e r ’ s G u i d e Chapter 3. FieldControl 3.1. Introduction FieldControl for Fieldbook E1 provides an overview of device settings, such as: Ø Battery Ø Brightness Ø Volume Ø Wi-Fi, WWAN, Bluetooth and GPS Ø Key mapping for programmable buttons NOTE: Only users with administrator privileges will be able to modify the device settings.
F i e l d b o o k E 1 U s e r ’ s G u i d e 3.2. FieldControl Overview 3.2.1. Launching FieldControl To launch FieldControl: 1. On the Home screen, tap 2. Tap . The All Apps screen opens. . NOTE: FieldControl can also be launched with a programmable hard button after the administrator sets the key map. The FieldControl language will automatically change with the language chosen in Android.
F i e l d b o o k E 1 U s e r ’ s G u i d e 3.2.2. Field Control Main Page The FieldControl main page may be viewed in Portrait or Landscape mode.
F i e l d b o o k E 1 U s e r ’ s G u i d e FieldControl E1 Main Page Landscape Mode The FieldControl main page is divided into two sections.
F i e l d b o o k E 1 U s e r ’ s G u i d e The right section provides easy access to key information. Tap an icon to display its contents. Icon Description Shows information on the following: • The current key mapping for the programmable function keys. • How to activate/deactivate Stealth mode. • How to change the key mapping. • A link to the Fieldbook E1 manual. Tap to open the manual. NOTE: Acrobat Reader is required to view the PDF file.
F i e l d b o o k E 1 U s e r ’ s G u i d e 3.3. Main Page Function Controls 3.3.1. Brightness You can manually adjust the brightness of the display, or enable AUTO BRIGHTNESS to use the factory default setting. To enable/disable AUTO BRIGHTNESS: Tap the controller (the button on the slider) to toggle auto and manual controls. Ø Green – indicates that AUTO BRIGHTNESS is enabled. Ø Red – indicates that you can set the brightness level manually.
F i e l d b o o k E 1 U s e r ’ s G u i d e 3.3.2. Volume To adjust the volume: Slide the controller to the left or right, according to your desired level. Adjusting the Volume 3.3.3. Auto-Rotation Tap this icon to activate or deactivate auto-rotation. A green dot appears at the bottom right corner of the icon to indicate that this function is activated. A red dot indicates that this function is deactivated.
F i e l d b o o k E 1 U s e r ’ s G u i d e 3.3.4. Profile Selection A profile consists of personalized settings. You can select from three profiles. When you run FieldControl for the first time, all profiles are in their default settings, and PROFILE 1 is activated.
F i e l d b o o k E 1 U s e r ’ s G u i d e Default Profile Settings Double Click-Home Launch the Internet browser Long Click-Home Settings 3.3.5. Radio control settings Airplane Mode Tap to activate/deactivate. When Airplane mode is activated, all wireless features of the device are turned off. When disabling Airplane mode, you will be prompted to confirm if you really want to continue. CAUTION: Some airlines prohibit the use of mobile devices, even on Airplane mode.
F i e l d b o o k E 1 U s e r ’ s G u i d e CAUTION: If Airplane mode is activated, you will be prompted to confirm if you want to disable Airplane mode. When you tap , other radio functions like WWAN (if available), Bluetooth, and WiFi are automatically activated. NOTE: Internet access may incur fees. Contact your service provider for details.
F i e l d b o o k E 1 U s e r ’ s G u i d e 3.4. Administrator Menu Go to the Administrator Menu to change default device settings, rename profiles, set an administrator password, and change the mapping of programmable function keys. NOTE: No password is required the first time FieldControl is used. Default Security Setting For subsequent uses, the administrator may set a password to prevent users from modifying settings.
F i e l d b o o k E 1 U s e r ’ s G u i d e Key in the Administrator Password 3. Tap the space for entering the password. The virtual keyboard is displayed. 4. Key in the password. The password is encrypted as you type, and the password field will only display asterisks (********) so the password will no longer be visible. 5. Tap OK to confirm. If login is successful, you will be directed to the Administrator Menu.
F i e l d b o o k E 1 U s e r ’ s G u i d e 3.5. Administrator Settings This Administrator Menu is divided into two sections. You will find Administrator Settings on the left side.
F i e l d b o o k E 1 U s e r ’ s G u i d e 3.5.1. Profile Settings FieldControl provides three profiles for the administrator to set different operating environments. A profile should include a profile title, configurations for the radio functions (Airplane mode, Bluetooth, WiFi, WWAN, and GPS), and the lock status of each radio function. You may modify default factory values if you have administrator privileges. To modify profile settings: 1. Tap the profile you want to modify.
F i e l d b o o k E 1 U s e r ’ s G u i d e 4. Tap the functions you want to activate or deactivate. 5. Tap the lock icons to lock/unlock your setting. Activating/Deactivating Radio Functions NOTE: A green dot at the bottom right corner of the icon means that the radio function is activated. A red dot means it is deactivated. NOTE: If the option is not installed on the device (e.g.
F i e l d b o o k E 1 U s e r ’ s G u i d e NOTES ON THE AIRPLANE MODE Ø While Airplane mode is activated, all other radio functions are disabled, regardless of their lock status. The administrator cannot make changes to the other radio functions until Airplane mode is disabled. Ø If Airplane mode is deactivated, the administrator can change the settings and lock status of the other radio functions.
F i e l d b o o k E 1 U s e r ’ s G u i d e Security Settings The following options are available: Ø Password required – A password to enter the Administrator Menu is required. Set or change the password using the password fields on the right. NOTE: No password is required the first time FieldControl is used. Ø No password required – Password protection is disabled. Setting or Changing the Password 1. To set the password for the first time, type “admin” at the prompt, then tap .
F i e l d b o o k E 1 U s e r ’ s G u i d e 3.5.3. Other Settings Other Settings Other Settings 1. Launch FieldControl at Directs you to FieldControl when your device starts up. system startup 2. Search automatically for Notifies you when a new update is available. NOTE: Requires Internet connection. FieldControl updates 3. Make “Stealth Allows you to press F+F3 hard keys to enable or mode” available disable “Stealth mode”. (Enable/Disable NOTE: Press for at least 2 seconds.
F i e l d b o o k E 1 U s e r ’ s G u i d e Other Settings 4. Disable the Webcam Disables the camera. NOTE: If this option is checked, you cannot use the assigned hard key to launch the camera. 5. Select your Sets the language to use for FieldControl. FieldControl NOTE: The choice may be different from the language language you set in the Android OS.
F i e l d b o o k E 1 U s e r ’ s G u i d e 3.6. Key Mapping This section allows you to assign functions to the programmable function keys. Key Mapping settings are found on the right section of the Administrator Menu. Key Mapping Tap to modify default function key assignments. Tap to view Help information.
F i e l d b o o k E 1 U s e r ’ s G u i d e 3.6.1. Default Function Key Assignments The table below shows the default function key assignments. Default Assignments NOTE: Double Click - the interval between clicks is 0.3 second. Long Click - the button should be pressed for at least 2 seconds.
F i e l d b o o k E 1 U s e r ’ s G u i d e 3.6.2. Modifying Function Key Assignments To modify the default function key assignments: 1. Tap . 2. Tap an item corresponding to a function key. (For example, “Launch Camera” for F2.) 3. From the list that displays, select a new function for the function key. 4. Tap to confirm, or to cancel. NOTE: Items in gray cells cannot be modified.
F i e l d b o o k E 1 U s e r ’ s G u i d e Ø Launch Internet browser Ø Launch email application Ø Auto-rotate enable/disabled When Stealth mode is set, the system requires the following conditions: Ø Deactivate all radios signals. Ø Set the brightness to zero. Ø Set the volume to zero Ø Deactivate the touch panel to avoid wrong manipulations. Ø Switch off all LEDs. Ø Lock all single-button functions except the Stealth mode switch button.
F i e l d b o o k E 1 U s e r ’ s G u i d e 3.7. Save Request Page If the administrator taps without saving changes, the following page displays: Save Request Page You can do any of the following: Ø Tap OK to exit without saving. Ø Tap Cancel to go back to the most recent page viewed or modified. Ø Tap Save to save all changes and go back to the FieldControl main page.
F i e l d b o o k E 1 U s e r ’ s G u i d e Chapter 4. Special Functions 4.1. Barcode Scanner Use the barcode scanner to look up information on products and services. To use the barcode scanner: 1. Press the assigned function key to launch the barcode scanner. NOTE: Key mapping is found in the FieldControl main page. The default assignment for the barcode scanner is F+F1. 2. Align the line onscreen to the middle area of the barcode you want to scan.
F i e l d b o o k E 1 U s e r ’ s G u i d e 4.2. RFID Scanner The device is equipped with a radio frequency identification (RFID) scanner for automatic identification and tracking of tags attached to objects with electronically stored information.
F i e l d b o o k E 1 U s e r ’ s G u i d e Chapter 5. Connecting to the Internet 5.1. WWAN If your device is equipped with a WWAN module, you can access the Internet using mobile cellular technology. NOTE: Make sure your 3G-enabled SIM card is inserted and you have a data plan. Check with your mobile operator. To connect to the Internet via WWAN: 1. On the Home screen, tap 2. Tap . The All Apps screen is displayed. . 3. Under WIRELESS & NETWORKS, tap More, then tap Mobile Networks.
F i e l d b o o k E 1 U s e r ’ s G u i d e 5.2. Wi-Fi You can access the Internet by connecting to a wireless network via an access point or “hot spot.” To connect to a wireless network: 1. On the Home screen, tap 2. Tap . The All Apps screen is displayed. . 3. Under WIRELESS & NETWORKS, tap the Wi-Fi On/Off switch to turn Wi-Fi on. The Wi-Fi LED indicator on the front panel turns on. 4. Tap Wi-Fi. A list of available Wi-Fi networks will be displayed. 5.
F i e l d b o o k E 1 U s e r ’ s G u i d e Chapter 6. Maintenance Your Fieldbook E1 needs occasional cleaning to prolong its life. Please read this section carefully to ensure proper care of Fieldbook E1. When it is necessary to clean it, use a soft, lint-free cloth, slightly dampened with a mild detergent solution. You may also use any commercially available computer cleaning kit. CAUTION: Never use petroleum-based solvents or harsh detergents to clean the system.
F i e l d b o o k E 1 U s e r ’ s G u i d e 6.2. Maintaining the LCD Display If the display screen has become smeared or dusty, clean the screen by applying a mild glass cleaner to a soft, clean, lint-free cloth, and then gently wipe the glass. Clean the LCD display only with a soft cloth dampened with denatured alcohol or a proprietary LCD screen cleaner. Ø Do not scratch the surface of the screen with any hard objects.
F i e l d b o o k E 1 U s e r ’ s G u i d e Chapter 7. Troubleshooting Refer to this resource page for useful information about the Android 4.2 operating system loaded in your tablet. Q1 How do I change the home screen wallpaper? To change the wallpaper, tap and hold your finger on the Home Screen to open your wallpaper options. Choose your wallpaper from the three options that may be available: • Gallery – allows you to set one of your own pictures as the wallpaper.
F i e l d b o o k E 1 U s e r ’ s G u i d e Q2 How do I add and remove apps, widgets, shortcuts and folders to the home screen? You can add and group your apps and shortcuts logically using home screen folders, just by dragging app icon onto a particular folder. Also, in All Apps launcher, you can simply drag an app to get information about it or immediately uninstall it, or disable a pre-installed application.
F i e l d b o o k E 1 U s e r ’ s G u i d e front-facing camera to register a face profile during setup in order to use during the unlock process. Just hold your device in front of you (face) to unlock. Q5 What are other ways to lock the screen? Use a PIN (Personal Identification Number) or screen lock pattern.
F i e l d b o o k E 1 U s e r ’ s G u i d e Once the mobile hotspot has been created and your device Wi-Fi is enabled, tap Wi-Fi settings to search for the wireless hotspot you created previously. Choose hotspot you created and, if necessary, enter the password if you have chosen to use one. After a few seconds, you should be able to access the internet through your smart phone’s data connection. NOTE: This only works if your smart phone is capable of creating a wireless hotspot.
F i e l d b o o k E 1 U s e r ’ s G u i d e • To exit from the Recent Apps list you can tap the down arrow in the lower-left corner or tap your screen outside of the apps list. Q9 How do I remove the browser history on my FieldBook E1? Internet browsers store a list of all the sites you visit called history.
F i e l d b o o k E 1 U s e r ’ s G u i d e Clear form data – removes information you entered in web forms. • Tap the item you wish to remove, and tap Ok to confirm. Q10 How can I explore files on my FieldBook E1 Android tablet? Although the Android operating system does not come with a native file managing application, there are many on Google Play that will allow you to better manage the space on your tablet’s internal memory or SD card.
F i e l d b o o k E 1 U s e r ’ s G u i d e Google's Android operating system makes it easy to automatically sync your account with their servers. To ensure that your personalized settings and applications are backed up please follow these steps: • Open the Settings application. • Click Privacy on the left menu. • Ensure that both Back up my data and Automatic restore are selected.
F i e l d b o o k E 1 U s e r ’ s G u i d e Q13 How do I improve a weak signal to my wireless network? When the signal strength is low, your wireless connection may become unreliable, slow or erratic. Wireless networks can be hindered by objects in between the antenna of the router or access point, and the wireless adapter in your computer.
F i e l d b o o k E 1 U s e r ’ s G u i d e NOTE: The FieldBook E1 does not come with a micro USB cable. Q15 How do I reset the hardware and software to factory defaults of FieldBook E1? You can reset the hardware software back to factory default configurations and have a fresh start. To do this, you can use the following method: • Turn off the device. • Press and hold the Volume Down button and Power button simultaneously. • Wait until the Android System Recovery Screen is displayed.
F i e l d b o o k E 1 U s e r ’ s G u i d e Q16 My FieldBook E1 does not display correct time and date even after adjusting the settings. How can I fix this? Replace the 3V lithium battery with a new one. The device uses a battery to retain system information. NOTE: Loss of BIOS settings occurs when the battery is removed. BIOS settings must be reconfigured whenever the battery is replaced.
F i e l d b o o k E 1 U s e r ’ s G u i d e • Choose the device name from the list of Bluetooth devices. • Click the Next button. • The devices may signal a notification alert, which lets you know that a file transfer is taking place. • Touch the Accept button. • The device will prompt a message once transfer is complete. NOTE: You won't see the device listed if Bluetooth is turned off.
F i e l d b o o k E 1 U s e r ’ s G u i d e Q20 How do I change the language on my FieldBook E1? Your Android tablet has the option to change the display language. Follow the steps below to change your display language: • Locate and tap the Settings icon. • Tap the Language & Input option. • Locate and choose the language you would like to use.
