User Manual

FCC_Compliance-Advisory_statement_June 2008.txt
Y-RK56 JNZRK56587 Y-RQ53 DZL131139
Y-RK56A JNZRK56587 Y-RR53 DZL131836
Y-RQ57 JNZ201774 Y-RQ52 DZL131836
Y-RX43 DZL201824 Y-RR57 DZL131836
Y-RW42 DZL201801 Y-RR54 DZL131836M
Y-RK49 JNZ201587 Y-RAJ56A JNZ201997
Y-RR71 JNZYRR71 Y-RR63 JNZ201968
Y-RAK73 DZL202065 Y-RAM74 DZL134041
Y-RAU7 JNZ202198 Y-RAR76 JNZ212336
Y-RAP78 JNZ212175 Y-RAS79 JNZ212336
Y-RAV80 DZL135446 Y-RAZ71 JNZYRAZ71
Y-RCP140 JNZYRCP140 Y-RBA78 JNZYRBA78
Y-UU87 DZLYUU87 Y-RBA97 JNZYRBA97
Y-RBH94 JNZYRBH94
R-RD8 JNZ201987
FCC Compliance and Advisory Statement.
This hardware device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: 1) this device may not cause harmful interference,
and 2) this device must accept any interference received, including interference
that may cause undesired operation. This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed or used in accordance with the
instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures: 1)
reorient or relocate the receiving antenna; 2) increase the separation between the
equipment and the receiver; 3) connect the equipment to an outlet on a circuit
different from that to which the receiver is connected; 4) consult the dealer or an
experienced radio/TV technician for help. Any changes or modifications not expressly
approved by the party responsible for compliance could void the user's authority to
operate the equipment. Where shielded interface cables have been provided with the
product or specified additional components or accessories elsewhere defined to be
used with the installation of the product, they must be used in order to ensure
compliance with FCC regulations.
© 2008 Logitech. Tous droits réservés. Logitech, le logo Logitech et les autres
marques Logitech sont la propriété exclusive de Logitech et sont susceptibles d’être
des marques déposées. Toutes les autres marques sont la propriété exclusive de leurs
détenteurs respectifs. Logitech décline toute responsabilité en cas d'erreurs dans
ce manuel. Les informations énoncées dans le présent document peuvent faire l’objet
de modifications sans avis préalable.
La "Déclaration FCC" suivante, s'applique à tous les produits Logitech en général
et spécifiquement aux produits listés ci-dessous:
Produits Logitech 2.4 GHz: ( puissance émise 100mW max):
Model names FCC ID Model names FCC ID
M-RAB81 DZL201662 M-RAP81 DZL201828A
M-RAN100 DZL201866 M-RBB93 JNZ201943
M-RBA97 DZL201945 M-RAY105 DZL201940
M-RBK93b JNZ201998 M-RBH113 DZL201966
Page 2