Specifications

ManualsBrandsLogoIncluded ManualsAudio EquipmentWireless earbuds

2.4GHz 2012 Chip Antenna: RANT2012F245C07

Dimension (mm)

2.05+-0.15

1.20+-0.15

0.85+-0.10

No. Terminal Name

Feeding/GNG

GND

Application:

WLAN, 802.11b/g, Bluetooth, WLAN, etc…

Features

SMD, high reliability, ultra Impact, Omni-directional…

Part number Information

RANT 2012

245

(A) (B)

(C)

(D) (E)

(F)

(A)Product Type Chip Antenna

(B) Size Code 2.0x1.2mm(+-0.2mm)

(D) Frequency 2.4 ~ 2.5GHz

(E) Feeding mode PIFA & Single Feeding

(F) Antenna type Type=06

Electrical Specification

Working Frequency Range 2400 ~2484 MHz

Bandwidth 84 (Min.)

Peak Gain 1.95 dBi (Typ.)

Impedance 50 Ohm

Return loss 10 dB ( Min)

Polarization Linear

Azimuth Beamwidth Omni-directional

Operation Temperature(

℃

) -40 ~85

℃

Resistance to Soldering Heats

10sec. ( @ 280℃)

Termination Ni / Au (Leadless)

The specification is defined on EVB.

Dimension and Terminal Configuration

RAIN International Technology Co., Ltd. TEL: 13530576606

Summary of content (5 pages)

PAGE 1
Application: WLAN, 802.11b/g, Bluetooth, WLAN, etc… Features SMD, high reliability, ultra Impact, Omni-directional… Part number Information RANT (A) 2012 (B) F (C) 245 (D) C (E) 07 (F) (A)Product Type Chip Antenna (B) Size Code 2.0x1.2mm(+-0.2mm) (C) Material High K material (D) Frequency 2.4 ~ 2.5GHz (E) Feeding mode PIFA & Single Feeding (F) Antenna type Type=06 Electrical Specification Working Frequency Range 2400 ~2484 MHz Bandwidth 84 (Min.) Peak Gain 1.95 dBi (Typ.
PAGE 2
Evaluation Board Reference PCB Dimension Antenna Layout Reference Unit :mm Electrical Characteristics Return Loss & Radiation Return Loss 1 Frequency(MHz) S11 (dB) 2400 -10.77 2450 -24.81 2484 -10.243 Radiation Z Y 2400MHz 2450MHz 2500MHz Efficiency 70.56% 75.25% 71.01% Peak Gain 1.72 dBi 1.95 dBi 1.69 dBi Directivity 2.26 dBi 2.69 dBi 2.11 dBi 2.
PAGE 3
Taping Specifications Reel and Taping Specification Reel Specification TYPE SIZE 2012 7” 5K/Reel A B C D 9.0±0.5 60±2 13.5±0.5 178±2 Tapping Specification Packaging Type Paper Type 2012 A B W E F 1.50±0.20 2.30±0.20 8.0±0.20 1.75±0.10 3.5±0.05 G 4.0±0.10 H T D 2.0±0.05 0.75±0.10 1.57±0.10 2.4GHz 2012 Chip Antenna: RANT2012F245C07 P 4.0±0.
PAGE 4
Reliability Table Test Item Procedure Electrical Characterization Requirements Ceramic Type Remark (Reference) Fulfill the electrical specification User Spec. Thermal Shock 1. Preconditioning: 50 ± 10℃ / 1 hr , then keep for 24 ± 1 hrs at room temp. 2. Initial measure: Spec: refer Initial spec. 3. Rapid change of temperature test: -30℃ to +85℃; 100 cycles; 15 minutes at Lower category temperature; 15 minutes at Upper category temperature. No Visible Damage. Fulfill the electrical specification.
PAGE 5
2.4GHz 2012 Chip Antenna: RANT2012F245C07 Board Flex (SMD) 1. Mounting method: IR-Reflow. PCB Size (L:100 × W:40 × T:1.6mm) 2. Apply the load in direction of the arrow until bending reaches 2 mm. No Visible Damage. AEC-Q200 005 Adhesion Force of 1.8Kg for 60 seconds. No Visible Damage Magnification of 20X or greater may be employed for inspection of the mechanical integrity of the device body terminals and body/terminal junction.