Owners manual

ManualsBrandslokar ManualsAutomotiveLokar ATS6350BM Auto Trans Shifter Kit

Building American Quality… With A Lifetime Warranty!

General Installation Notes:

Please read these instructions completely before beginning the installation. If

you have any questions please call.

Before beginning the installation, disconnect the negative battery cable and use

wheel chocks to block the vehicle's wheels.

Make sure the engine, transmission, body and frame are properly grounded.

Refer to Fig. 1 for the component names.

Tools and Materials Required:

• Standard Allen wrenches: 1/8", 5/32", 3/16", 7/32"

• Wrench or Socket Sizes: 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 7/8"

• Tape Measure

• Metal cutting tool, such as a hacksaw or a die grinder with a cut-off wheel

• Ohmmeter

• Wire cutters/strippers

• Wire crimping or soldering tools

• Blue thread locking compound

Lokar Shifters are designed to fit specific transmissions. Before you begin

the installation, verify that you have the proper model for your transmission.

If your Shifter does not seem to fit properly, do not make modifications during

installation as this may void your warranty. Call for assistance.

Verify that the length of the Shifter you have purchased is what you actually

want. When installed, the bottom of the shifter lever will be approximately

3-1/2" - 4” above the transmission case. From that point up to the top of the

knob is how the shifter length is determined.

If you mount the shifter assembly all the way forward, using the four bolt holes

at the very front of the main plate, a bell crank kit (Lokar Part No. S-6999, sold

separately) will be required.

Before attempting to make any adjustments, the Shifter must be installed on the

transmission and the transmission should be installed into the vehicle.

The shifter lever is designed to lock in Park and in Neutral. You must depress

the release button in the top of the shifter knob in order to shift out of Park or

Neutral. The release button will only be flush with the top of the shifter knob

when the shifter lever is in Park or Neutral.

To shift from Park directly to Drive, depress the release button and then hold it down

while moving the shifter lever, and the shifter lever will automatically stop in the Drive

position. Once you release the button, the shifter lever can be moved into 2nd gear.

You must depress the release button again to shift down into 1st gear.

These instructions assume that you have full access to the transmission when the

installation is begun, with the transmission removed from the vehicle, or the vehicle

body removed from the chassis.

TOLL FREE 1-877-469-7440 • (865) 966-2269 • FAX (865) 671-1999 • tech@lokar.com • www.lokar.com

TH350 Automatic Trans Mount Shifter

Installation Instructions

TH350 Automatic Trans Mount Shifter

Installation Instructions

INS0079 Rev. 08/31/2017

Page 1

Fig. 1

Shifter

Lever

Shifter

Assembly

Shifter

Knob

Right Side

Bracket

Optional Handbrake

Mounting Location

Main

Plate

Rod

End

Rod

End

1/4"-28 x 1" Button Head

Bolt with Flat Washer and

Nylock Nut

1/4"-28 x 1" Button Head

Bolt with Flat Washer and

Nylock Nut

3/8"-24 x 1" Tension Set

Screws and Jam Nuts

3/8"-16 x 1-1/4"

Button Head Bolts

& Lock Washers

Rear Mounting

Bracket

5/16"-24 x 1/2"

Button Head Bolts

and Lock Washers

5/16"-24 x 5/8" Tension Set

Screws with Jam Nuts

Side Mounting Buttons

Trans

Gear

Lever

Left Side

Bracket

Aluminum

Adjuster Plug

Quad

Lever

Threaded Rod with

1/4"-28 Jam Nuts

Release Button

Summary of content (6 pages)

PAGE 1
TH350 Automatic Trans Mount Shifter Installation Instructions Building American Quality… With A Lifetime Warranty! ® TOLL FREE 1-877-469-7440 • (865) 966-2269 • FAX (865) 671-1999 • tech@lokar.com • www.lokar.com TH350 Automatic Trans Mount Shifter Installation Instructions Release Button General Installation Notes: Please read these instructions completely before beginning the installation. If you have any questions please call.
PAGE 2
Mounting Bracket Assembly Front of Vehicle 5/16"-24 x 1/2" Button Head Bolts and Lock Washers (Three Each Side) Hollow Boss with Side Mounting Button Installed Right Side Bracket Fig. 2 Step 1: I f your vehicle already has a shifter of any type installed, disconnect all shifter linkage and remove the shifter and its related hardware (neutral safety switch, back-up light switch, etc.).
PAGE 3
Step 8: ( Continued) Transfer that measurement to the transmission (or to the engine/transmission assembly if the engine is not installed in the vehicle). Mark that location on the main plate. The holes in the main plate that are closest to your mark are where the FRONT banana bracket bolts will need to be installed. Fig.
PAGE 4
12 3/4" act 1r t b u S e and istanc D s i h ure T Meas Trans Gear Lever at approximately 1:00 position in Park 9 3 6 Fig. 7 Fig. 8 Threaded Rod Step 11: P ut the shifter lever into the Park position and check the position of the quad lever. It will need to be pointing to about the 4:30 - 5:00 position. If it is not, loosen the set screw in the top of the quad lever with a 1/8" Allen wrench and slide the quad lever off of the shaft.
PAGE 5
Trans Gear Lever Rod End Flat Washer 1/4"-28 x 1" Button Head Bolt 1/4"-28 Nylock Nut Switch Plate Neutral Safety Switch and Washer NOTE: The bolt can be installed from either side, but make sure the rod end is sandwiched between the flat washer and the trans gear lever. 1/4"-28 Jam Nut Right Side Banana Bracket Threaded Rod 5/16"-24 x 3/8” Button Head Bolts Fig. 10 Fig.
PAGE 6
Neutral Safety Switch Adjustment and Wiring Release Button Step 16: F or the neutral safety switch to function properly, the shifter linkage must be adjusted correctly. Do not attempt to adjust the neutral safety switch unless you have completed Step 15. The Lokar Neutral Safety Switch is a simple on/off, nondirectional switch. The switch passes current (turns on) when the ball is pushed in. It does not pass current (turns off) when the ball is out at its at-rest position.