5/8-Port 10/100/1000M Gigabit Switch User’s Manual Ver 2.
The device is a powerful, high-performance Gigabit Ethernet switch, with all ports capable of 10, 100 or 1000Mbps auto-negotiation operation (NWay), which means the switch could automatically negotiate with the connected partners on the network speed and duplex mode. It is ideal for micro-segmenting large networks into smaller, connected subnets for improved performance, enabling the bandwidth demanding multimedia and imaging applications.
Please refer to the following table for LED definition 5-Port 8-Port LED Status Power Steady Green Off 1000M Steady Green 100M Steady Green 10M Steady Green Blinking Green Operation Power is on Power is off Connected as 1000Mbps Connected as 100Mbps Connected as 10Mbps The port is transmitting/receiving data.
Connect each station to the switch by twisted-pair cable. Plug one RJ-45 connector into a RJ-45 port of the switch, and plug the other RJ-45 connector into the station’s network adapter. Power on the switch and then system is ready. For cable selection, refer to the following table. In making a switch interconnection, you could use any port to connect another switch with straight or crossover cable.
Standard IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3x full duplex operation and flow control Interface 5 /8* 10/100/1000Mbps RJ-45 Gigabit Ethernet Ports Uplink Auto MDI/MDI-X(Auto crossover) Network Speed 10/100/1000Mbps & Full/Half duplex mode auto detection (1000Mbps for Full duplex only) MAC Addr.
FCC Certifications This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Einleitung Dieses Gerät ist ein hochleistungsfähiger Gigabit Ethernet Switch, dessen Ports alle die 10, 100 oder 1000Mbps Auto-Negotiation Funktion (NWay) unterstützen. Dies bedeutet, dass der Switch automatisch mit den angeschlossen Partnern über die Netzwerkdatenrate und den Duplexmodus verhandeln kann.
LED Anzeigen Bitte beachten Sie die folgende Tabelle für die Bestimmung der LED Anzeigen: LED Power 1000M 100M 10M Status Ständig grün Aus Ständig grün Ständig grün Ständig grün Grün blinkend Operation Power an Power aus Verbunden als 1000Mbps Verbunden als 100Mbps Verbunden als 10Mbps Der Port übermittelt / empfängt Daten.
Stationsverbindungen Verbinden Sie jede Station durch ein twisted-pair Kabel mit dem Switch. Stecken Sie ein RJ-45 Kabel in einen RJ-45 Port des Switchs, und stecken Sie die das andere Ende des RJ-45 Kabels in den Netzwerk Adapter der Station. Schalten Sie den Switch an. Das System ist nun bereit. Für die Kabelwahl beachten Sie bitte die folgende Tabelle. Switchverbindung Um eine Verbindung zwischen Switches zu machen, können Sie jeden Port benutzen um einen anderen Switch anzuschließen.
Spezifikationen Standards IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.
FCC Zertifizierungen Dieses Gerät ist getestet worden und, gemäß Teil 15 der FCC Vorschriften, als den Beschränkungen eines digitalen Gerätes der Klasse B entsprechend befunden worden. Diese Einschränkungen sind dazu bestimmt, angemessenen Schutz gegen schädliche Störungen bei der Benutzung im Geschäftsumfeld zu bieten.
Cet appareil est un interrupteur Gigabit Ethernet puissant et hautement performant, avec une capacité d’opérations d’auto négociation (Nway) pour tous ses ports de 10, 100 ou 1000 Mbps, ce qui signifie que l’interrupteur est capable de négocier automatiquement avec les partenaires connectés sur la vitesse du réseau et le mode bidirectionnel.
Veuillez consulter le tableau ci-dessous pour obtenir les caractéristiques DEL DEL Etat Fonctionnement Sous Vert continu Sous tension tension 1000M Eteint Hors tension Vert continu Connecté à 1000Mbps 100M Vert continu Connecté à 100Mbps 10M Vert continu Connecté à 10Mbps Vert clignotant Le port est en cours de transmission / réception d’informations.
Reliez chaque station à l’interrupteur à l’aide du câble double torsadé. Branchez un connecteur RJ-45 à un port RJ-45 de l’interrupteur, et branchez l’autre connecteur RJ-45 dans l’adaptateur de réseau de station. Allumez l’interrupteur, et le système est prêt. Pour choisir le câble, consulter le tableau suivant. Pour réaliser une interconnexion d’interrupteur, vous pouvez utiliser n’importe quel port pour brancher un autre interrupteur au moyen d’un câble direct ou de croisement.
Standard IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3x fonctionnement en bidirectionnel simultané et contrôle de flux Interface 5/8 ports * 10/100/1000Mbps RJ-45 Gigabit Ethernet Liaison montante Auto MDI/MDI-X(Auto croisement) Vitesse réseau du 10/100/1000Mbps & mode bidirectionnel simultané et non simultané auto détection (1000Mbps pour bidirectionnel simultané uniquement) Tableau adr.
Certificats FCC Cet appareil a été testé et certifié conforme aux conditions relatives au matériel numérique de catégorie B, selon le paragraphe 15 des Normes FCC. Ces limites ont été conçues pour fournir une protection raisonnable contre des interférences nocives lorsque l’appreil est utilisé dans un environnement commercial.
Questo dispositivo è uno switch Gigabit Ethernet potente e ad alte prestazioni, con tutte le porte in grado effettuare operazioni di autonegoziazione a 10, 100 o 1000Mbps (NWay), il che significa che lo switch può negoziare automaticamente la velocità e la modalità duplex con gli elementi collegati.
Per la definizione dei LED consultare la seguente tabella LED Power 1000M 100M 10M Stato Verde fisso Spento Verde fisso Verde fisso Verde fisso Verde lampeggiante Funzionamento Apparecchio acceso Apparecchio spento Collegato a 1000Mbps Collegato a 100Mbps Collegato a 10Mbps La porta sta trasmettendo/ricevendo dati.
Collegare ogni postazione allo switch usando un doppino intrecciato. Inserire un connettore RJ-45 in una delle porte RJ-45 dello switch e l’altro connettore RJ-45 nell’adattatore di rete della postazione. Accendere lo switch e il sistema è già pronto. Per la scelta del cavo, consultare la seguente tabella. Per fare un collegamento tra switch si può usare una porta qualsiasi usando un cavo diretto o cross-over.
Norme IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.
Certificazioni FCC L’apparecchiatura è stata collaudata e riscontrata conforme ai limiti per i dispositivi digitali di classe B ai sensi della Parte 15 della normativa FCC. Tali limiti sono stati studiati per fornire una ragionevole protezione contro le pericolose interferenze negli ambienti commerciali.
Introducción Acaba de adquirir un potente conmutador Gigabit Ethernet de alto rendimiento. Todos sus puertos disponen de negociación automática a 10, 100 o 1.000 Mbps (NWay), es decir, que el conmutador puede negociar automáticamente la velocidad de red y el modo dúplex con las partes conectadas. Es ideal para microsegmentar redes grandes en subredes más pequeñas y conectadas para obtener un mejor rendimiento, y permite la demanda de ancho de banda para aplicaciones de imagen y multimedia.
Definición de los LED En la siguiente tabla encontrará la definición de los indicadores LED. LED Estado Power Verde fijo Apagado 1000M Verde fijo 100M Verde fijo 10M Verde fijo Verde parpadeante Significado El conmutador está encendido El conmutador está apagado Conectado a 1.
Conexión de las estaciones Asocie las estaciones al conmutador mediante un cable de par trenzado. Conecte un conector RJ-45 a uno de los puertos RJ-45 del conmutador y el otro conector RJ-45 al adaptador de red de la estación. A continuación, encienda el conmutador; el sistema estará listo. Para seleccionar los cables, consulte la tabla que encontrará más adelante.
Especificaciones Estándares IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3x funcionamiento full-duplex y control de flujo Interfaz 5/8 puertos RJ-45 Gigabit Ethernet 10/100/1.000 Mbps Uplink Auto MDI/MDI-X(Auto crossover) Velocidad de red Detección automática de 10/100/1.000 Mbps y modo full/half-duplex (1.000 Mbps sólo para full-duplex) Tabla de direcciones 4.096 direcciones MAC MAC Memoria 128 Kb Jumbo Frame Fuente alimentación EMI 12.
Certificación de la FCC Se ha comprobado que este aparato cumple los límites para dispositivos digitales de clase B, de conformidad con el apartado 15 de las normas de la FCC. Dichos límites han sido diseñados para proporcionar una protección razonable contra interferencias perjudiciales en instalaciones comerciales.
Certyfikacja FCC Niniejsze urządzenie zostało przetestowane i zatwierdzone jako zgodne z wymogami dla urządzeń cyfrowych klasy B, na podstawie Części 15 Reguł FCC. Wymagania te są tak zaprojektowane, by zapewniać odpowiednią ochronę przed szkodliwymi zakłóceniami podczas użytkowania urządzenia w środowisku mieszkalnym.
zachodzi możliwość, iż informacje zawarte w tym dokumencie są nieaktualne. Uprasza się o sprawdzienie aktualności zawartych tutaj informacji u lokalnego dystrybutora. Żadna część tego dokumentu nie może zostać skopiowana lub powielona w jakiejkolwiek formie bez pisemnej zgody producenta. Znaki towarowe: Wszystkie nazwy firmowe i znaki towarowe są własnościami ich poszczególnych producentów. Prawo autorskie © 2005, wszelkie prawa zastrzeżone.
Niniejsze urządzenie jest zaawansowanym i wysokowydajnym przełącznikiem Gigabit Ethernet, z portami o zdolnościach auto-negocjacji 10, 100 lub 1000Mbps (NWay), co oznacza, iż przełącznik jest w stanie automatycznie negocjować z połączonymi w sieci partnerami w trybie speed i duplex. Jest on idealnym rozwiązaniem w przypadku mikrosegmentacji dużych sieci na mniejsze, połączone podsieci, celem poprawy wydajności, umożliwiając zastosowanie szerokopasmowych rozwiązań multimedialnych oraz aplikacji graficznych.
Proszę odnieść się do następującej tabeli po opis diod LED 5-Port 8-Port LED Status Power Zielony ciągły Wyłączone 1000M Zielony ciągły Zielony mruga 100M Zielony ciągły Zielony mruga 10M Zielony ciągły Zielony mruga Operacja Zasilanie włączone Zasilanie wyłączone Połączenie przy 1000Mbps Port przesyła/otrzymuje dane. Połączenie przy 100Mbps Port przesyła/otrzymuje dane. Połączenie przy 10Mbps Port przesyła/otrzymuje dane.
Połącz każdą stację z przełącznikiem przy użyciu skrętki komputerowej (kabla sieciowego). Wetknij jedną wtyczkę RJ-45 do portu RJ-45 przełącznika, a drugą wtyczke RJ-45 do adaptera siecowego stacji. Włącz zasilanie przełącznika i system jest gotowy do pracy. Celem wyboru kabli, sięgnij po następującą tabelę. Dokonując połączenia z innym przełącznikiem, możesz użyć dowolnego portu, używając kabla prostego lub skrosowanego.
Standard IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.
61NB-G2080-200C 34
DECLARATION OF CONFORMITY CE = European Community Conformity Mark We, Manufacturer/Importer Longshine Technologie (Europe) GmbH An der Strusbek 9 22926 Ahrensburg Germany Declare That The Product LCS-GS7108 8-Port Gigabit Switch Desktop Is In Conformity With: Standards EN 55022 :1994+A1:1995+A2:1997, Class B EN 61000-3-2 :2000, Class A* see note * below) EN 61000-3-3:1995+A1:2001 EN 55024:1998+A1 :2001+A2 :2003 IEC 61000-4-2:2001 IEC 61000-4-3:2002+A1:2002 IEC 61000-4-4:1995+A1:2000+A2:2001 IEC 61000-4-5:20
DECLARATION OF CONFORMITY CE = European Community Conformity Mark We, Manufacturer/Importer Longshine Technologie (Europe) GmbH An der Strusbek 9 22926 Ahrensburg Germany Declare That The Product LCS-GS7105 5-Port Gigabit Switch Desktop Is In Conformity With: Standards EN 55022 :1994+A1:1995+A2:1997, Class B EN 61000-3-2 :2000, Class A* see note * below) EN 61000-3-3:1995+A1:2001 EN 55024:1998+A1 :2001+A2 :2003 IEC 61000-4-2:2001 IEC 61000-4-3:2002+A1:2002 IEC 61000-4-4:1995+A1:2000+A2:2001 IEC 61000-4-5:20