6/24-Port Gigabit Switch User’s Manual English Deutsch Español Français Italiano Polski
The device is a powerful, high-performance Gigabit Ethernet switch, with all ports capable of 10, 100 or 1000Mbps auto-negotiation operation (NWay), which means the switch could automatically negotiate with the connected partners on the network speed and duplex mode. It is ideal for micro-segmenting large networks into smaller, connected subnets for improved performance, enabling the bandwidth demanding multimedia and imaging applications.
Please refer to the following table for LED definition.
Connect each station to the switch by twisted-pair cable. Plug one RJ-45 connector into a RJ-45 port of the switch, and plug the other RJ-45 connector into the station’s network adapter. Power on the switch and then system is ready. For cable selection, refer to the following table. In making a switch interconnection, you could use any port to connect another switch with straight or crossover cable.
Standard IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3x full duplex operation and flow control Interface 16/24* 10/100/1000Mbps RJ-45 Gigabit Ethernet Ports Uplink Auto MDI/MDI-X(Auto crossover) Network Speed 10/100/1000Mbps & Full/Half duplex mode auto detection (1000Mbps for Full duplex only) MAC Addr.
FCC Certifications This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Einleitung Dieses Gerät ist ein hochleistungsfähiger Gigabit Ethernet Switch, dessen Ports alle die 10, 100 oder 1000Mbps Auto-Negotiation Funktion (NWay) unterstützen. Dies bedeutet, dass der Switch automatisch mit den angeschlossenen Partnern über die Netzwerkdatenrate und den Duplexmodus verhandeln kann.
Bevor Sie beginnen den Switch zu installieren, überprüfen Sie bitte den folgenden Inhalt dieser Packung: Ein Gigabit Ethernet Switch Ein externes Netzteil Ein Netzspannungskabel Handbuch LED Anzeigen Bitte beachten Sie die folgende Tabelle für die Bestimmung der LED Anzeigen: 16-Port 24-Port LED Strom Link/Act Status Operation Grün Gerät ist an Aus Gerät ist aus Grün Port verbunden Blinkendes Grün Der Port übermittelt/ sendet Daten 7
Stationsverbindungen Verbinden Sie jede Station durch ein twisted-pair Kabel mit dem Switch. Stecken Sie ein RJ-45 Kabel in einen RJ-45 Port des Switches, und stecken Sie die das andere Ende des RJ-45 Kabels in den Netzwerk Adapter der Station. Schalten Sie den Switch an. Das System ist nun bereit. Für die Kabelwahl beachten Sie bitte die folgende Tabelle. Switchverbindung Um eine Verbindung zwischen Switchen herzustellen, können Sie jeden Port benutzen, um einen anderen Switch anzuschließen.
Spezifikationen Standards IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.
FCC Zertifizierungen Dieses Gerät ist getestet worden und, gemäß Teil 15 der FCC Vorschriften, als den Beschränkungen eines digitalen Gerätes der Klasse A entsprechend befunden worden. Diese Einschränkungen sind dazu bestimmt, angemessenen Schutz gegen schädliche Störungen bei der Benutzung im Geschäftsumfeld zu bieten.
Introducción Acaba de adquirir un potente conmutador Gigabit Ethernet de alto rendimiento. Todos sus puertos disponen de negociación automática a 10, 100 o 1.000 Mbps (NWay), es decir, que el conmutador puede negociar automáticamente la velocidad de red y el modo dúplex con las partes conectadas. Es ideal para microsegmentar redes grandes en subredes más pequeñas y conectadas para obtener un mejor rendimiento, y permite la demanda de ancho de banda para aplicaciones de imagen y multimedia.
Antes de instalar el conmutador, compruebe que el paquete contiene los siguientes componentes: Un conmutador Gigabit Ethernet Un adaptador de corriente externo Un cable de alimentación Manual del usuario Definición de los LED En la siguiente tabla encontrará la definición de los indicadores LED.
Conexión de las estaciones Asocie las estaciones al conmutador mediante un cable de par trenzado. Conecte un conector RJ-45 a uno de los puertos RJ-45 del conmutador y el otro conector RJ-45 al adaptador de red de la estación. A continuación, encienda el conmutador; el sistema estará listo. Para seleccionar los cables, consulte la tabla que encontrará más adelante.
Especificaciones Estándares IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3x funcionamiento full-duplex y control de flujo Interfaz 16/24 puertos RJ-45 10/100/1.000 Mbps Uplink Auto MDI/MDI-X(Auto crossover) Velocidad de red Detección automática de 10/100/1.000 Mbps y modo full/half-duplex (1.
Certificación de la FCC Se ha comprobado que este aparato cumple los límites para dispositivos digitales de clase A, de conformidad con el apartado 15 de las normas de la FCC. Dichos límites han sido diseñados para proporcionar una protección razonable contra interferencias perjudiciales en instalaciones comerciales.
Cet appareil est un interrupteur Gigabit Ethernet puissant et hautement performant, avec une capacité d’opérations d’auto négociation (Nway) pour tous ses ports de 10, 100 ou 1000 Mbps, ce qui signifie que l’interrupteur est capable de négocier automatiquement avec les partenaires connectés sur la vitesse du réseau et le mode bidirectionnel.
Veuillez consulter le caractéristiques DEL tableau ci-dessous pour obtenir les 16-port 24-port LED Power Link/Act État Indication Vert fixe Le switch est allumé Éteint Le switch est éteint Vert fixe Le port est connecté Vert Intermittent Le port transfer/reçoit des données 17
Reliez chaque station à l’interrupteur à l’aide du câble double torsadé. Branchez un connecteur RJ-45 à un port RJ-45 de l’interrupteur, et branchez l’autre connecteur RJ-45 dans l’adaptateur de réseau de station. Allumez l’interrupteur, et le système est prêt. Pour choisir le câble, consulter le tableau suivant. Pour réaliser une interconnexion d’interrupteur, vous pouvez utiliser n’importe quel port pour brancher un autre interrupteur au moyen d’un câble direct ou de croisement.
Standard IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3x fonctionnement en bidirectionnel simultané et contrôle de flux Interface 16/24 ports * 10/100/1000Mbps RJ-45 Gigabit Ethernet Liaison Auto MDI/MDI-X(Auto croisement) montante Vitesse du 10/100/1000Mbps & mode bidirectionnel simultané et réseau non simultané auto détection (1000Mbps pour bidirectionnel simultané uniquement) Tableau adr.
Certificats FCC Cet appareil a été testé et certifié conforme aux conditions relatives au matériel numérique de catégorie A, selon le paragraphe 15 des Normes FCC. Ces limites ont été conçues pour fournir une protection raisonnable contre des interférences nocives lorsque l’appreil est utilisé dans un environnement commercial.
Questo dispositivo è uno switch Gigabit Ethernet potente e ad alte prestazioni, con tutte le porte in grado effettuare operazioni di autonegoziazione a 10, 100 o 1000Mbps (NWay), il che significa che lo switch può negoziare automaticamente la velocità e la modalità duplex con gli elementi collegati.
Per la definizione dei LED consultare la seguente tabella 16-porte 8-porte LED Stato Funzionamento Power Verde fisso Spento Apparecchio acceso Apparecchio spento Link/Act Verde fisso Porta connessa Verde lampeggiante La porta stà trasmettendo/ricevendo dati 22
Collegare ogni postazione allo switch usando un doppino intrecciato. Inserire un connettore RJ-45 in una delle porte RJ-45 dello switch e l’altro connettore RJ-45 nell’adattatore di rete della postazione. Accendere lo switch e il sistema è già pronto. Per la scelta del cavo, consultare la seguente tabella. Per fare un collegamento tra switch si può usare una porta qualsiasi usando un cavo diretto o cross-over.
Norme IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.
Certificazioni FCC L’apparecchiatura è stata collaudata e riscontrata conforme ai limiti per i dispositivi digitali di classe A ai sensi della Parte 15 della normativa FCC. Tali limiti sono stati studiati per fornire una ragionevole protezione contro le pericolose interferenze negli ambienti commerciali.
Niniejsze urządzenie jest zaawansowanym i wysokowydajnym przełącznikiem Gigabit Ethernet, z portami o zdolnościach auto-negocjacji 10, 100 lub 1000Mbps (NWay), co oznacza, iż przełącznik jest w stanie automatycznie negocjować z połączonymi w sieci partnerami w trybie speed i duplex. Jest on idealnym rozwiązaniem w przypadku mikrosegmentacji dużych sieci na mniejsze, połączone podsieci, celem poprawy wydajności, umożliwiając zastosowanie szerokopasmowych rozwiązań multimedialnych oraz aplikacji graficznych.
Proszę odnieść się do następującej tabeli po opis diod LED 5-Port 8-Port LED Zasilanie Link/Act Stato Funzionamento Zielony Off Zielony Migoczacy Zielony Zasilanie jest włączone Zasilanie jest wyłączone Port podłączony Port transmituje/odbiera dane 27
Połącz każdą stację z przełącznikiem przy użyciu skrętki komputerowej (kabla sieciowego). Wetknij jedną wtyczkę RJ-45 do portu RJ-45 przełącznika, a drugą wtyczke RJ-45 do adaptera siecowego stacji. Włącz zasilanie przełącznika i system jest gotowy do pracy. Celem wyboru kabli, sięgnij po następującą tabelę. Dokonując połączenia z innym przełącznikiem, możesz użyć dowolnego portu, używając kabla prostego lub skrosowanego.
Standard IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.
Certyfikacja FCC Niniejsze urządzenie zostało przetestowane i zatwierdzone jako zgodne z wymogami dla urządzeń cyfrowych klasy A, na podstawie Części 15 Reguł FCC. Wymagania te są tak zaprojektowane, by zapewniać odpowiednią ochronę przed szkodliwymi zakłóceniami podczas użytkowania urządzenia w środowisku mieszkalnym.
English "CE Mark Warning: This is a Class A product. In a domestic enviroment this product may cause radio interferences in which case the user may be required to take adequate measures." German "CE Zeichen Warnung: Dies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im Wohnbereich Funkstörungen verursachen; in diesem Fall kann vom Betreiber verlangt werden, angemessene Massnahmen durchzuführen." Spanish “Advertencia de conformidad CE: Este es un producto de Clase A.