Assembly Instruction Sheet

ManualsBrandsLongshore Tides ManualsCeiling LightsMeghan 5 - Light Unique / Statement Dome Pendant

1of4

(1)A19MediumBasebulb100WMaximum.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Note:This CONVERTIBLEfixturecanbemountedaspendantlightorsemi-flushlight.Refertorespective

installationsteps forinstallations.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Shade

Fixture Body

Package Contents

Crossbar

Assembly

6” Rod

12” Rod

Hex

Nut

Flat

Washer

Ceiling

Canopy

Swivel

Nipple

Figure 1A

Supply Wires and

Ground Wire

STEP 2A - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the outlet box

with the head of the green ground screw facing you. Secure the

Crossbar Assembly (A) with outlet box screws (not included).

Tighten until snug.

Supply Wires

with Ground Wire

Outlet Box Screws

(not included)

Outlet

Box

Figure 2A

Upper Collar

Steel Collar

Harp with

Socket Collar

Flat Washer

Rubber Washer

Diffuser

Small Flat

Washer

Finial

Nipple

STEP 1A - Install Ceiling Canopy, Rods and Socket Assembly

together

A. Thread Nipple (G) onto the Swivel (H). Place Ceiling Canopy (F) and

Flat Washer (E) over the Nipple (G), secure by threading Hex Nut

(D) onto the Nipple (G), tighten until sung.

B. Determine the Rods (B/C) to be assembled to the Fixture Body (I)

according to your hanging height.

C. Pass the supply wires and ground wire through the chosen rods

Assembly Instructions for Pendant Light

(Step 1A - Step 7A)

(Continue to Step 1A)

(B/C) and the Ceiling Canopy with Swivel.

Thread the Fixture Body (I), the chosen

Rods (B/C) and the Ceiling Canopy with

Swivel together. Hand tighten until snug.

Suggested rods for Ceiling height :

8’ ceiling : use (2) 12” rods

9’ ceiling : use (2) 6” rods and (2) 12” rod

STEP 3A - Test Fitting Ceiling Canopy to Crossbar Assembly

A. Remove mounting balls from the Crossbar Assembly (A). Fit the

Ceiling Canopy (F) to the Crossbar Assembly (A) and secure with

mounting balls. Note: The Ceiling Canopy (F) should be snug

against the ceiling and the mounting balls. If not, adjust the length of

the nipple on the Crossbar Assembly (A) by unscrewing the

preassembled hex nut and lock washer and then screwing the

mounting screws in or out of the crossbar until the correct length is

Assembly Instruction Sheet

Thank you for purchasing a product.

Need assistance with parts or assembly? Call our customer service

Summary of content (4 pages)

PAGE 1
Assembly Instruction Sheet Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (1) A19 Medium Base bulb 100W Maximum. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
STEP 7A - Install Diffuser (Step 3A Continued) achieved. Once the Ceiling Canopy (F) is secure, remove the mounting ball and Ceiling Canopy (F) and proceed to Step 4A. A. Thread one Hex Nut (D) to the Nipple (N) approx half way. Screw the Nipple (N) into the bottom end of the Harp (M) and tighten until snug. By using pliers, thread the Hex Nut (D) against the Harp (M) and hand tighten until snug. B.
PAGE 3
STEP 2B - Installing the Crossbar Assembly STEP 5B - Install the Fixture A. Pass the supply wires from outlet box through the Crossbar Assembly (A). Attach the Crossbar Assembly (A) to the outlet box with the head of the green ground screw facing you. Secure the Crossbar Assembly (A) with outlet box screws (not included). Tighten until snug. A. Carefully tuck all wires into the outlet box and position the Ceiling Canopy (F) over the outlet box.
PAGE 4
FINISH: IMPERIAL SILVER PENDANT LIGHT 5” Dia. 51” OVERALL HEIGHT INCLUDES (2) 6” AND (2)12” RODS 11.5” 13.5” Dia. SEMI-FLUSH 5” Dia. 13” 13.5” Dia. NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4" Thank you for purchasing a product.