Assembly Instruction Sheet

1of2
(3)B10CandelabraBaseBulbs60WMaximum
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
A
Crossbar Assembly
x1
B
Fixture
Body
x1
STEP 1 - Installing the Crossbar Assembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box
with the head of the Green Ground Screw facing you. Secure the
Crossbar Assembly (A) with Outlet Box Screws (not included).
Tighten until snug.
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
Figure 1
STEP 2 Test Fitting Ceiling Canopy to Crossbar Assembly-
A.
eiling canopy to the
ceiling
Remove mounting balls from the Crossbar Assembly (A). Fit the
c and Fixture Body (B) Crossbar Assembly (A)
and secure with mounting balls. Note: The should be
snug against the and the mounting balls. If
ceiling canopy
not, adjust the
length of the nipple on the Crossbar Assembly (A) by unscrewing
the preassembled hex nut and lock washer and then screwing the
Mounting Screw
Hex Nut and
Lock Washer
Mounting Ball
A
Figure 2
B
mounting screws in or out of
the crossbar until the correct
length is achieved. Once the
ceiling canopy and Fixture
Body (B) is secure, remove
the mounting ball and ceiling
canopy and Fixture Body (B)
and proceed to Step 3.
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
STEP 4 Install the Fixture-
A. Carefully tuck all wires into
the outlet box and position
the ceiling canopy and
Fixture Body (B) over the
outlet box. Align the holes in
the ceiling canopy with the
mounting screws, then
attach the ceiling canopy
and Fixture Body (B) using
the previously removed
mounting balls. Hand
tighten until snug.
Mounting
Screw
Mounting Ball
A
B
Figure 4
STEP 5 s- Install Bulb
A. Insert bulbs onto sockets and
screw snugly into place.
Your fixture is now assembled
and ready to use. Enjoy!
Bulb (not
supplied)
Socket
Figure 5
Assembly Instruction Sheet