Smart Toilet Instructions
Table of contents Specifications Cautions and Warnings 2 Part List 6 Control Description 9 Installation Instructions 13 Preparation for The First Time Use 14 Battery Installation 15 Packing List 16 Maintenance and Cleaning 17 Troubleshooting 19
Specifications CAUTIONS AND WARNINGS Technical Specification Product Name Smart Toilet Rated Voltage 110-120V~ Rated Frequency 60Hz Rated Power 1150W * Flush volume Waterproof Level Supply Water Pressure Minimum Water Pressure Codes/ Standards Warm Water Temp. 4 levels (Room Temperature- 104°F) Warm Air Temp. 4 levels (Room Temperature- 140°F) Heated Seat Temp. 4 levels (Room Temperature- 105°F) Environment Temp. 41- 104°F 1.28gpm(4.
CAUTIONS AND WARNINGS Do not use a loose and unstable power socket. Doing so may cause fire or electrical shock. Please insert the power plug into the AC 110V to 60Hz and 15A or above socket. Failure to do so may result in fire or electric shock. When the power exceeds the socket specification, it will cause the socket to heat and cause a fire. STOP CAUTIONS AND WARNINGS Fire NO Fire Do not apply strong force, mechanical shock, step on or stand on the toilet seat, toilet lid or main unit.
CAUTIONS AND WARNINGS Must obey Must obey Part List ● Do not expose to direct sunlight. Doing so may cause changes in color or the product malfunction. ● Do not urinate on the main unit, toilet seat or wand. Doing so may cause a failure or discoloration. ● Loose the connection of power cord during thunderstorms. ● When not using the product for a long time, close the shutoff valve, and then turn off the power of the product.
Part List ● Remote Part List Control (shall be subject to the actual object) ● Remote Control (shall be subject to the actual object) WATER AUTO LID SEAT STOP REARWASH LADYWASH OSCILLATING OSCILLATING DRYER/AIR TEMP.
Control Description Stop Automatic Flush After Leave Press " STOP " button to terminate the function of "rear wash"/"lady wash"/"dryer". When enabled (user seated at least 10 seconds), the toilet will automatically flush after the user stands up. Rear Wash/Oscillating Turn the knob to " REAR WASH " mode, or press “ REAR WASH " icon on the remote control, water spray from the rear outlet of the wand will be activated.
Control Description Motion-Activated Open/Close Lid (This feature is unique to the automatic flip toilet) When enabled, the lid automatically open/close when the toilet front motion sensor senses user’s motion such as [near], [using] or [leaving]. Auto Flushing by Foot Sensor (Foot Kick) (This feature is unique to the toilet which flushing by foot sensor /foot kick.) 1.
Installation instruction Installation instruction Required Tools: Screwdriver Wrench Marker Tape measure Caulking gun Electric drill Pre-Installation Precautions: 1.Water Pressure Test: Ensure that water flow exceeds 1.32 gallons within 15 seconds. 2.Prior to installation, run hot water through the pipes for 2 minutes and then connect them to the inlet water pipe before proceeding with the installation. Installation Steps: 1.
Installation instruction Installation instruction 8.Apply a circle of anti-mold sealing silicone at the junction between the toilet and the floor. After the silicone sealant has solidified, plug in the power and slowly open the angle valve. Adjust the water pressure to be within 80 PSI and inspect the seals of all connection points. 3.Place a flange ring underneath the toilet. Sewage Outlet Flange Ring 4.
Preparation For the Pirst Time Use Installation instruction Install the remote control battery Note: This product utilizes an advanced cyclonic siphonic jet flushing technology. In areas with higher water pressure (exceeding 3 kilograms of pressure), there might be a slight occurrence of splashing and jet noise during the cyclonic flush on the ceramic surfaces.
Battery Installation Packing list Battery replacement method (only for external battery box toilet bowl) 1、Taking out the battery box and install it to the back of the ceramic 2、And find the connector of the battery box and connect the line NO. Name 1 Smart Toilet 2 Water Shutoff Valve 3 Flange Ring 4 Instruction 5 Remote Control Quantity Remark including bracket and 3M tape ● There will be no further notice if any change due to product improvement and technical update.
Maintenance and Cleaning Maintenance and Cleaning To prevent product damage, please do as following: • Always test your cleaning solution on an inconspicuous area before applying to the entire surface. • Wipe surfaces clean and rinse completely with water immediately after applying cleaner. Rinse and dry any over spray that lands on nearby surfaces. • Do not allow cleaners to soak on surfaces. • Use a soft, dampened sponge or cloth.
Troubleshooting Troubleshooting Use following way to check the abnormal status, if it still does not work, please call professionals Symptoms Stops in the middle of use Low water temperature Low warm air temperature No warm wind suddenly Low seat temperature Water heating indicator flushes Seat heating indicator flushes All indicators flush Toilet leakin 23 Probable causes Symptoms Recommended Corrective action Cleansing features stop automatically after 2 minutes of continuous use.
