Quick Start Manual

www.lorextechnology.com
LW2730/LW2930 Series Quick Start Guide_R1 Page 1
• Cameras are rated for indoor/outdoor installation. Not intended
for direct exposure to rain or snow. For outdoor applications
install under shelter protected from the elements.
• Wireless cameras require a power source to operate.
• When adding cameras that were not included in the original
box, you will need to pair up the camera with the receiver.
Please refer to the camera pairing section of the User’s Guide.
• This camera includes an Auto Mechanical IR Cut Filter. When the
camera changes between day/night lighting, an audible clicking
noise may be heard coming from the camera. This clicking is
normal, and indicates that the camera filter is working.
NOTE: AVOID INSTALLING IN A LOCATION WHICH REQUIRES THE
WIRELESS SIGNAL TO PASS THROUGH CEMENT, CONCRETE AND METAL
STRUCTURES. THIS WILL REDUCE THE TRANSMISSION RANGE.
Getting Started
This system comes with the following
components:
• LCD monitor with built-in recorder and
wireless receiver*
• Indoor/outdoor color camera(s)*
• Camera stand(s)*
• SD memory card*
• Audio/video cable
• Mounting hardware kit(s)*
• Wireless antennas (for reveiver and
camera [s])*
• Power adapters*
• User’s Guide
• Mini USB cable
• CD
*
Monitor size, number of cameras and
SD card capacity may vary by model.
Check your package for specific content
information.
A. Camera Setup
3
Connect one end of the camera
Power Adapter to the camera
and the other end to an electrical
outlet. Make sure the power
connector is fully pushed in to
avoid water getting in the plug.
1
B. LCD Receiver Setup
Attach the included
antenna to the
camera by screwing
it on to the side as
shown below.
2
The LCD Receiver can be setup for use on a tabletop, or mounted to a wall or underneath a counter or cupboard. See the User’s Guide for full mounting details.
3
Insert the included SD card into
the SD Card slot on the LCD
receiver until you hear a “click.”
The card will not be flush when
completely inserted.
NOTE: The receiver is compatible
with most major brands of SD card
up to 32 GB.
For the LW2730
Series, the switch is
located on the back
of the screen.
For the LW2930
Series, the switch is
located on the side of
the screen.
Connect one end of the
receiver power adapter to
the bottom of the receiver
and the other end to an
electrical outlet.
• Make sure to first connect the camera(s) to an electrical
outlet before powering on the receiver; this will ensure a
proper connection.
4
5
Slide the power switch
to the “ON” position.
21
6
Adjust the antenna on the
receiver as necessary to
provide the clearest
reception.
Pull out the receiver
stand for convenient
placement on a flat
surface.
Connect the antenna by
turning it clockwise onto the
receiver’s antenna jack.
NOTE: If one or more of the cameras do not appear when selected (i.e. Camera 2 is turned on but does not appear on channel 2), follow the pairing
process as described in User’s Guide.
Skill Level
Intermediate
easy
advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Skill Level
Intermediate
easy
advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time Tools Skills - Easy
Under 20 Minutes*
Hand Tools Plug & Play connections,
On screen set up
* Installation time may vary
based on application and
camera location
SIMPLY AWARE
™
*
NOTE: Remove the
protective film from
the front of the
camera. If the film is
not removed, it will block
the built-in microphone
and potentially affect the
quality of the picture.
WIRELESS VIDEO MONITORING SYSTEM
LW2730/LW2930 SERIES
QUICK START GUIDE
Protective
film
Before you install a camera, carefully plan where and how
it will be positioned, and where you will route the cable
that connects the camera to the power adapter.
Attach camera to the mounting stand. Adjust the angle
of the camera until the desired view is set. Tighten the
thumbscrews to secure the desired camera position.
Thumbscrews