User Manual

ManualsBrandsLosi ManualsCars & Trucks1/8 8IGHT 4WD Nitro Buggy RTR, Red/Yellow

LOSI 8IGHT/8IGHT-T RTR • INSTRUCTION MANUAL

1/8-SCALE HIGH-PERFORMANCE 4WD NITRO BUGGY

• Losi

8IGHT™ Nitro RTR: 1/8-Scale 4WD Buggy (LOS04010V2)

• Spektrum™ SLT3™ 2.4GHz Transmitter (SPMSLT300)

• SLR300 3-Channel 2.4GHz SLT Receiver (SPMSLR300)

• Dynamite

.21 Nitro Pull-Start Engine (DYNE0570)

• Dynamite

6V 1600mAh Ni-MH Receiver Pack, 3+2 Hump (DYN1453)

• 9KG Servo, Waterproof, 23T (SPMS605)

• S614S Steel Gear Waterproof Servo, 23T (SPMS614S)

Tools Included

• 4-Way Cross Wrench

• Bind Plug

Needed to Complete

• 20–30% Nitromethane fuel

• Nitromethane-Approved Dispenser

• NiMH Charger

• Glow Igniter

Use only Dynamite

tools or other high-quality tools. Use of inexpensive tools

can cause damage to the small screws and parts used on this type of model.

Components

Wet Conditions Maintenance

• Remove the battery pack(s) and dry the contacts. If you have an air compressor

or a can of compressed air, blow out any water that may be inside the recessed

connector housing.

• Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off

with a garden hose. Avoid rinsing the bearings and transmission.

NOTICE: Never use a pressure washer to clean your vehicle.

• Use an air compressor or a can of compressed air to dry the vehicle and help

remove any water that may have gotten into small crevices or corners.

• Spray the bearings, drive train, fasteners and other metal parts with a water-

displacing light oil or lubricant.

• Let the vehicle air dry before you store it. Water (and oil) may continue to drip

for a few hours.

• Increase the frequency of disassembly, inspection and lubrication of the

following:

• Front and rear axle hub assembly bearings.

• All transmission cases, gears and differentials.

• Engine air ﬁlter element.

• Engine clutch assembly, including shoes and bearings.

1/8-SCALE HIGH-PERFORMANCE 4WD NITRO TRUGGY

• Losi

8IGHT-T™ Nitro RTR: 1/8-Scale 4WD Truggy (LOS04011V2)

• Spektrum™ SLT3™ 2.4GHz Transmitter (SPMSLT300)

• SLR300 3-Channel 2.4GHz SLT Receiver (SPMSLR300)

• Dynamite

.28 Nitro Pull-Start Engine (DYNE0571)

• Dynamite

6V 1600mAh Ni-MH Receiver Pack, 3+2 Hump (DYN1453)

• 9KG Throttle Servo, Waterproof, 23T (SPMS605)

• S614S Steel Gear Waterproof Servo, 23T (SPMS614S)

Tools Included

• 4-Way Cross Wrench

• Bind Plug

Needed to Complete

• 20–30% Nitromethane fuel

• Nitromethane-Approved Dispenser

• NiMH Charger

• Glow Igniter

Use only Dynamite

tools or other high-quality tools. Use of inexpensive tools

can cause damage to the small screws and parts used on this type of model.