User guide

41
DETAIL ICON REFERENCE KEY
HARDWARE
Cap Head Flat Head 1 Flat Head 2 Button Head
Set Ball Bearings 1 Ball Bearings 2
Pins
Washers Shims Retaining Clips
Nuts (Lock/Plain)
Body Clip (A8200)
2-56 x 1/4" (A6232)
2-56 x 1/2" (A6254)
4-40 x 1/2" (A6204)
4-40 x 3/8" (A6206)
4-40 x 5/8" (A6221)
5-40 x 7/8" w/ 5/8" Shoulder (A4414)
4-40 x 1/4" (A6234)
4-40 x 1/2" (A6256)
5-40 x 3/8" (A6277)
5-40 x 1/2" (A6278)
2-56 x 1/4" (A6255)
5-40 x 3/4" (A6279)
5-40 x 7/8" (A6282)
5-40 x 1" (A6280)
5-40 x 3/8" (A6270)
5-40 x 1/2" (A6271)
5-40 x 3/4" (A6272)
5-40 x 5/8" (A6275)
5-40 x 7/8" (A6273)
5-40 x 1-7/8" (A6273)
8-32 x 3/8" (A6264)
8-32 x 1/2" (A6262)
F 5-40 x 1/8" (A6228)
C 4-40 x 1/8" (A6227)
C 5-40 x 3/16" (A6299)
C 8-32 x 1/8" (A6298)
F 5-40 x 1/8" (A6297)
F 8-32 x 1/8" (A6296)
O10-32 x 3/8" (A6295)
5-40 x 22mm (A6045)
6x10x3mm (A6946)
5x11x4mm (A6947)
F 5x11x4mm (A6948)
5x10x4mm (A6949)
1/2” x 3/4" (A6953)
8x14x4mm (A6945)
5x13x4mm (A6949)
Ball Stud (A6215)
#4 x .030" (A6350)
.250 x .094 x .020" (A9166)
#5-40 (A6302)
3 x 8mm (A9106)
3 x 12mm (A3500)
#4-40 (Mini) (A6306)
#8-32 (A6311)
2.5 x14mm (A3526)
2.5 x 12.37mm (A3523)
3 x 17mm (A3531)
2.5 x 12.8mm (A3503)
4 x 66mm (A6500)
3.5 x 53mm (A6503)
5x7x.2mm (A6356)
6x11x.2mm (A3501)
14x17x.1mm (A4452)
14x17x.25mm (A4452)
5mm E-clip (A6109)
5-40 x 1/2" (A6240)
8-32 x 3/4" (A6263)
8-32 x 5/8" (A6266)
GLUE
Apply CA Glue
Pay Special
Attention
CUT
Cut/Trim
Ensure Free
Movement
Ensure Free
Rotation
Ensure Proper
Orientation
Push Firm
Tighten
L
R
L
R
Assemble
Other
Side the Same
L
Side
Shown
x2
Repeat/Build
Multiple
Screw Partially
DO NOT
Over Tighten/
Snug Tight
1
These numbers are used to identify the critical order in which assembly must occur. *Note: They will not call out every stage of the assembly process.
Apply Losi-Lok™
GREASE
Apply High
Pressure Black
Grease
Degrease with
Motor Spray
OIL
Fill With
Silicone Oil
Pre-Tap
LOSI-LOK