Instruction Manual
WELCOME XXX-NT SPORT OWNER!
Thank you for choosing the Team Losi XXX-NT Sport as your vehicle to enjoy the exciting world of nitro powered all-terrain racing. The
XXX-NT Sport is the result of hundreds of hours of computer-aided design and on-track testing by our world champion development
team. The XXX-NT Sport represents the latest in technology and meets the unique demands of nitro powered off-road racing.
Since fuel powered models tend to require greater mechanical tuning ability, it is important that you read through this manual
completely before beginning assembly. A little extra time now will save building time and help get your new truck running sooner. You
will find that our unique bag-by-bag assembly is both quick and easy to follow. You will also notice that we have included a separate
tip section along with helpful hints throughout this manual to help you tune your XXX-NT Sport and maximize your enjoyment of this
model.
Once again, thank you for making a wise choice… the XXX-NT Sport.
Team Losi
NOTES & SYMBOLS USED
Figure 1
This is a common figure number found at the beginning of each
new illustration throughout the manual.
Step 1. - Each step throughout the entire manual has a check box
to the left of it. As you complete each step, mark the box with a check.
If you need to take a break and return to building at a later time you will
be able to locate the exact step where you left off.
*NOTE: This is a common note. It is used to call attention to
specific details of a certain step in the assembly.
IMPORTANT NOTE: Even if you are familiar with Team
Losi kits, be sure and pay attention to these notes. They point
out very important details during the assembly process. Do not
ignore these notes!
Tip: This designates a performance tip. These tips are not neces-
sary, but can improve the performance of your
XXX-NT Sport truck.
In illustrations where it is important to note which
direction parts are pointing, a helmet like this one will be in-
cluded in the illustration. The helmet will always face the front of
the car. Any reference to the right or left side will relate to the
direction of the helmet.
KIT/MANUAL ORGANIZATION
The XXX-NT Sport is composed of different bags marked A through
F. Each bag contains all of the parts necessary to complete a
particular section of the truck. Some of these bags have subas-
sembly bags within them. It is essential that you open only one
bag at a time and follow the correct sequence, otherwise you
may face difficulties in finding the right part. It is helpful to read
through the instructions for an entire bag prior to starting assem-
bly. Key numbers (in parentheses) have been assigned to each
part and remain the same throughout the manual. In some illus-
trations, parts which have already been installed are not shown
so that the current steps can be illustrated more clearly.
1. INTRODUCTION
XXX-NT SPORT COMPLETED DIMENSIONS
Length: 16-1/2" Front Width: 12-3/4" Rear Width: 12-3/4" Height: 5-1/4"
Wheel base: 11-1/4" All dimensions at ride height. Weight will vary depending on accessories.
i
For your convenience, an actual size hardware identification guide
is included with each step. To check a part, hold it against the silhou-
ette until the correct part is identified. In some cases extra hardware
has been supplied for parts that may be easy to lose.
The molded parts in the XXX-NT Sport are manufactured to de-
manding tolerances. When screws are tightened to the point of being
snug, the parts are held firmly in place. For this reason it is very impor-
tant that screws not be overtightened in any of the plastic parts.
To insure that parts are not lost during construction, it is recom-
mended that you work over a towel or mat to prevent parts from rolling
away.
IMPORTANT SAFETY NOTES
1. Select an area for assembly that is away from the reach
of small children. The parts in the kit are small and can be swal-
lowed by children, causing choking and possible internal injury.
2. The shock fluid and greases supplied should be kept out
of children’s reach. They were not intended for human consump-
tion!
3. Exercise care when using any hand tools, sharp instru-
ments, or power tools during construction.
4. Carefully read all manufacturer’s warnings and cautions
for any glues, fuel, or paints that may be used for assembly and
operating purposes.
5. Gas powered vehicles should not be operated indoors.
6. Be careful when handling your truck after it has been run
for any period of time. The engine and many parts can get ex-
tremely hot during operation.
TOOLS REQUIRED
Team Losi has supplied all Allen wrenches and a special wrench
that is needed for assembly and adjustments. The following
common tools will also be required: Small flatblade screwdriver,
Phillips screwdriver, needle nose pliers, regular pliers, scissors,
or other body cutting/trimming tools. 3/16", 1/4", 5/16", and 3/8"
nut drivers are optional.