Nitro Monster Truck Operations Guide TM Dodge and HEMI are trademarks of Chrysler LLC. Dodge Ram and its trade dress are used under license by Horizon Hobby, Inc. © Chrysler LLC 2007 Not responsible for errors. All prices subject to change without notice. Losi, a Division of Horizon Hobby, Inc.
Introduction Thank you for choosing the Losi Raminator Monster Vehicle. This is a highly developed off-road model that features a sophisticated computer-based radio system and does require some mechanical experience and direct adult supervision. This guide contains the basic instructions and drawings for operating and maintaining your new Raminator. Please take the time to read through it completely before running the model.
Required Equipment You will need the following items to operate your new Raminator. 4 AA alkaline batteries for the transmitter Losi™ Nitrotane™ 20% Sport Fuel. (LOSF0020 or LOSF0120) This is the only fuel that supports the engine warranty. Fuel bottle (LOSB5201) 6V Receiver Pack (LOSB9949 or similar) Tools You Will Find Handy In addition to the tools included with the Raminator, you will find the following both useful and in some cases necessary.
1H our Base Start-up Settings from the Factory High Speed Needle—23/4 turns out from bottom Low Speed Needle—3 turns out from bottom 2H Engine Tuning After the engine is broken in, you can tune it for optimum performance. When tuning, it is critical that you be cautious of overheating as severe damage and premature wear can occur. You want to make all carburetor adjustments in “one hour” increments.
Hi Speed Adjustment After initial acceleration the engine should pull at a steady rate while maintaining a two-stroke whine and a noticeable trail of smoke. If the engine labors and is sluggish with heavy smoke, the mixture is too rich and needs to be leaned by turning the high speed needle clockwise in one hour increments until it runs smoothly. If the engine isn’t smoking or starts to die after acceleration, it is too lean and you must richen the mixture by turning the needle counterclockwise.
About the Radio The Losi DSM radio installed in the Raminator is a state of the art system featuring the latest technology that requires no crystals. This system includes all the features you may find useful. Be sure to read through the Radio operation instructions on what and how to use these features. The following is a simple guide to items and functions commonly referred to. 1. 2. 3. 4. 5. 6. 7. Steering Wheel - Controls the trucks direction (left/right).
Steps to Re-Bind 1. Ensure that the transmitter and vehicle are both turned off. 2. Using the supplied Bind plug (which looks like a standard receiver plug with a wire loop installed) insert the Bind plug into the receiver slot labeled “BIND”. Looking down on the receiver this slot would be below the LED and is the farthest from the LED, or nearest to the corner of the receiver. Note: You do not need to remove any of the other plugs to re-bind. 3. With the Bind plug installed, turn on the vehicle.
Radio Operation It is important that you familiarize yourself with the radio system, as this is your direct link to the model. • Never run your model with low receiver or transmitter batteries. • Never leave the power on or the batteries will not last long. • Always turn the transmitter ON before turning the model ON. • When finished running, always turn the model OFF before the transmitter.
2-Speed Adjustment When new and during engine break-in, the two speed will not shift. Only after the engine has been broken in and the needle valve adjusted, if necessary, will it start shifting. You may need to adjust the shift point after a while as the shoes wear in. Although pre-adjusted at the factory, the two speed can be adjusted to shift at the point that suits you best. Under normal circumstances, it should shift slightly before the engine reaches maximum power.
Replacing the 2-Speed Gears Be sure to replace the one-way bearing in the same direction as removed. Replacing the Clutch Bell Use a 3/32” wrench (provided) to remove the retaining screw (turn counterclockwise) while firmly holding the flywheel with a pair of pliers. Remove the screw, washers and clutch bell, being careful not to lose any shims that may be used. Remove the ball bearings and brush any loose dirt away from the bearing faces.
Servicing the Differentials The differentials should be serviced periodically. Be sure to clean and inspect all of the gears and replace if severely worn. Always use plenty of high-quality grease (like Losi LOSA3066 or LOSA99203) on all gears. NOTE: These can also be made into racing-type viscous diffs as noted below. Always service one diff at a time and pay close attention to installing the housing with the “TOP” marking up so it can be seen looking down on the chassis. Fig 1. Fig 2. Fig 3.
Servicing the Transmission The Transmission should also be cleaned and serviced periodically. All gears and shafts should be closely inspected for wear and replaced if necessary. Always use a high quality grease or lubricant to prevent premature wear and/or failure. Removing the Transmission 1. Remove the gear cover. 2. Remove the throttle linkage from the carburetor and the brake linkage from the servo arm. 3. Loosen the four motor mount screws (bottom of the chassis) and slide the motor back. 4.
Rebuilding/Refilling the Shocks Tools Needed Step 1. After removing the shock, push up on the lower spring cup and snap it off of the shaft. Remove the spring. Step 2. Turn the shock upside down and, using the included shock tool, remove the black shock cartridge/shaft assembly from the shock body by turning it counterclockwise. NOTE: If you only wish to change or fill the shock fluid, skip to step 6. B2900 A6234 B2876 B2815 Step3. Remove the 1/4" nut by turning it counterclockwise.
Quick Reference Guide Initial Factory Settings Using Nitrotane 20% Sport Fuel Engine x 23/4 x3 High Speed Needle - 23 /4 turns out Low Speed Needle - 3 turns out Transmission x1 Slipper - 1 turn out Axles & Nuts x5 Two Speed - 5 turns out Shocks Tie Rods 2.7 in.
M26SS Customer Support Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, IL 61822 1-877-504-0233 Problem Engine won't start.................................. Troubleshooting Chart Things to Check M26SS Customer Support Horizon Hobby, Inc.
Raminator Replacement Parts List RADIO PARTS LOSB0806 LOSB0807 LOSB0818 LOSB0819 MRX 3000 Pro DSM Receiver........................................... $109.99 MTX Pro DSM Transmitter.................................................. $69.99 MSX Digital Servo............................................................... $16.99 MSX Digital Hi-Torque Servo............................................... $26.99 SUSPENSION PARTS LOSB2001 LOSB2101 LOSB2102 LOSB2201 F/R Suspension Arms (pr) (LST/AFT)...........
Raminator Optional Parts List OPTIONAL PARTS MOTOR ACCESSORIES SUSPENSION PARTS LOSB2221 Sway Bar Kit (LST/2)........................................................... $14.99 CHASSIS PARTS LOSB2260 LOSB2261 LOSB2262 LOSB2263 LOSB2264 LOSB2270 LOSB2271 LOSB2272 LOSB2273 LOSB2274 LOSB2501 SHOCKS LOSB2801 LOSB2802 LOSB2803 LOSB2804 LOSB2805 LOSB2806 LOSB2807 LOSB2808 LOSB2811 LOSB2813 LOSB2814 LOSB2841 LOSB2879 LOSB2901 LOSB2949 LOSB2951 LOSB2952 Heavy Duty Chassis Plate - Hard Ano. (LST/2)...........
A6250 B3128 A6248 A6355 B4203 B3601 A6206 B3132 B3605 A6206 B3133 A6940 B3125 B3102 B3132 B3125 A6107 A6940 B3138 A6247 A6246 B3102 B3128 A6250 TRANSMISSION ASSEMBLY A6941 B3118 A6940 B3127 B3125 B3127 B3118 A6940 B3136 A6107 A6941 B3135 B3138 B3125 B3603 B3605 Page 18
Drivetrain Assembly B5021 B5020 B3455 A6201 A6350 B3409 B3455 A6937 B3404 B3423 B4202 B5051 B5020 B3322 B3341 A6937 B3301 A6240 A6350 A6356 B3301 B3421 B3505 B3323 B3301 B3301 A6250 B2257 B3541 B3125 B5051 B3401 B3450 B3545 B5049 B3451 B3540 B3539 B3532 B5052 B3533 A6250 B3505 B-3538 B3538 A6356 A6356 A6942 A6210 B3534 B3539 B3538 B3545 B3541 A6206 A6250 B2257 A6942 B3534 B6350 A6942 B3534 B3538 B3537 B3538 B3533 Page 19 B5062 B5056 A6305
B2256 B2256 Page 20
Page 21
FRONT ASSEMBLY Page 22
B2451 REAR ASSEMBLY Page 23
DYN0929 LOSR1038 DYN0930 DYN0932 DYN0928 LOSR1038 DYN0933 LOSR1038 LOSR1038 DYN0924 LOSR1024 LOSR1021 (Optional LOSR1022) LOSR1023 TM LOSR1039 LOSR1038 LOSR1025 LOSR1020 DYN0927 LOSR1026 DYN0923 LOSB4204 LOSR1027 DYN0913 LOSB3301 DYN0911 DYN0909 LOSR1028 DYN0926 LOSR1030 LOSB5051 DYN0926 LOSR1042 M26MB Engine w/Pull/Spin-Start DYN0931 CARBURETOR LOSR1037 LOSR1038 LOSR1029 DYN0915 Page 24
Warranty Period Exclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties that the Products purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase by the Purchaser. Limited Warranty (a) This warranty is limited to the original Purchaser (“Purchaser”) and is not transferable. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER.
Questions, Assistance, and Repairs Your local hobby store and/or place of purchase cannot provide warranty support or repair. Once assembly, setup or use of the Product has been started, you must contact Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please direct your email to productsupport@horizonhobby. com, or call 877.504.0233 toll free to speak to a service technician.
Accessories/Hop-Ups Page LOSA7650S Super King Pin Tires $34.99 LOSA99104 Losi Race Wrench Four-Piece Inch Set $49.99 LOSA99168 Clutch Shoe/Spring Tool $7.00 LOSB2221 Sway Bar Kit (LST/2) $14.99 LOSB2807 Shock Body & Cap Set Red (4) (LST/2/AFT) $68.99 LOSB2808 Shock Body & Cap Set Gold (4) (LST/2/AFT) $68.99 LOSB2814 Hard Ano. Thrd. Shock Body & Adj. Set (4) (LST/2/AFT) $58.99 LOSB2841 Titanium Nitride Shock Shaft (LST/2/AFT) $7.50 LOSB3193 Inside Gear Cover (LST2) $5.
Page 28