/18-scale ready-to-run mini monster truck Operation Manual Before operating this vehicle, please read all printed materials thoroughly. CONNECT - REGISTER - WIN Visit WWW.LOSI.COM and follow the product registration link to stay connected. For registering your Losi Product you will be automatically entered for a chance to win the Losi Pick-Your-Prize Sweepstakes of $1,000 (retail value) based on winner preference. Not responsible for errors. All prices subject to change without notice.
Table of Contents Introduction....................................................................... 2 Getting Started..............................................................3-4 Safety Precautions........................................................... 5 Suggested Tools............................................................... 5 Radio System Overview................................................5-6 Radio System binding...................................................... 6 ESC Setup.......
Getting Started STEP 1 STEP 2 Plug the charger into the proper wall receptacle then the battery into the charger and let it charge for 3 hours for the first time. For subsequent charges allow 5 to 6 hours for a full charge. Remove the transmitter battery cover, install four (4) AA batteries (Pay close attention to the polarity of the positive (+) and negative (-) ends) and replace cover. STEP 3 Step 3.
STEP 4 STEP 5 Off Off On On Always turn on the transmitter first. The small red and green lights above the switch should both light up. If not, you need to check for low or incorrectly installed batteries. Once the transmitter has been powered on, turn on the Mini HIGHroller by sliding the switch on the ESC to the “On” position. STEP 6 ft After you have finished, turn the Mini Ri HIGHroller off FIRST by sliding the ESC gh t Le STEP 7 ST Trim switch to the “OFF” position.
Safety Precautions This is a sophisticated radio controlled model that must be operated with caution and common sense. Failure to operate your Mini HIGHroller in a safe and responsible manner could result in damage to the model and property. The Mini HIGHroller is not intended for use by children without direct adult supervision.
The Transmitter 1. Steering Wheel: Controls direction (left/right) of the model. 3 9 10 1 6 7 2. Throttle Trigger: Controls speed and direction (forward/ reverse) of the model. 3. Antenna: Transmits signal to the model. 4. On/Off Switch: Turns the power on/off for the transmitter. 5. Indicator Lights: Green (right) light indicates adequate battery power. Red (left) indicates signal strength. 6. ST. Trim: Adjusts the “hands off” direction of the model. 8 5 4 2 7. TH.
ESC Setup The ESC comes from the factory preset and ready for use. If for some reason you should need to reset the ESC, use the following instructions. 1. Turn on the transmitter and ESC. Press the setup button — both the RED and GREEN LEDs will come on. 2. Pull the throttle trigger all the way back (full speed) and press the setup button once — only the GREEN LED will come on. 3. Push the throttle trigger full forward (brake/reverse) and push the setup button once — only the RED LED will come on. 4.
Steering Rate Your transmitter is equipped with a steering rate control to the left of the steering wheel. This advanced feature, usually found only on competition-type radios, allows you to adjust the amount the front tires move when you turn the steering wheel. This is really helpful when you are on slick, as well as high-traction surfaces. If your Mini HIGHroller turns too sharply and/or spins out easily, try turning the steering rate down by rotating the knob counterclockwise (to the left).
Maintainence If you have any problems other than those covered in the troubleshooting section, please call the service department at (877) 504-0233. They will be able to give your specific problem additional attention and instruct you as to what needs to be done. Cleaning Performance can be hindered if dirt gets in any of the moving suspension parts. Use compressed air, a soft paintbrush,or toothbrush to remove dust or dirt.
Changing the Pinion Gear/Gear Ratio Before you change the pinion gear ask yourself why you are doing it. In general, if you change to a larger pinion the top speed will improve but you will see less acceleration and run time. Changing to a smaller pinion will give you quicker acceleration and possibly a bit longer run time but a little less top speed. This would be good for short layouts or when running hotter motors. The pinion on the Mini HIGHroller offers the best balance of both.
1/18 MINI HIGHROLLER TROUBLESHOOTING GUIDE Symptom Possible Cause(s) Possible Solution(s) Doesn’t operate Battery not charged or plugged in Receiver switch not “On” Transmitter not “On” or low battery Charge battery/plug in Turn on receiver switch Turn on/replace batteries Motor runs but rear wheels don’t move Pinion not meshing with spur gear Pinion spinning on motor shaft Slipper too loose Transmission gears stripped Adjust pinion/spur mesh Replace pinion gear on motor Check & adjust slipper Repla
Rebuilding/Refilling the Shocks Step 1 Step 2 After removing the shock, push up on the lower spring cup and remove it from the shaft. Remove the spring and preload spacers. Turn the shock upside down and remove the black shock cartridge/shaft assembly from the shock body by turning it counterclockwise. Note: If you only wish to change or fill the shock fluid, skip to step 5. Step 3 Step 4 Remove the top E-clip from the shock shaft. Remove the shock piston. Remove second E-clip.
Warranty Information the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability.
Warranty Inspection and Repairs Germany: Electronics and engines requiring inspection or repair should be shipped to the following address: To receive warranty service, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be repaired or replaced free of charge. Repair or replacement decisions are at the sole discretion of Horizon Hobby.
Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, IL 61822 USA Declaration of Conformity (in accordance with ISO/IEC 17050-1) No. HH20091129 Product(s): LOS 1/18 Mini HIGHroller RTR Item Number(s): LOSB0207 Equipment class: 1 The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC: EN 300-328 Technical requirements for Radio equipment.
Notes: 16
1/18-SCALE READY-TO-RUN MINI MONSTER TRUCK 17
Replacement Parts Price List Option Parts LOSB0805 Losi DSM Transmitter LOSB0806 Losi DSM Receiver LOSB0813 MS20DSL Servo with Long Lead LOSB0826 MSC20RB Electronic Speed Control LOSB1009 Main Chassis LOSB1018 Front Bulkhead, Kickplate & Brace LOSB1020 F/R Pivot Block Set LOSB1024 F/R Suspension Arm Set LOSB1027 Spindle, Carrier and Rear Hub Set LOSB1029 Steering Bellcrank Set LOSB1037 Front Axle and Pin Brace Set LOSB1040 Camber and Steering Link Set LOSB1041 Suspension Pin Set LOSB1042 Front/Rear Shoc
LOSB1042 LOSB1020 LOSB1041 LOSB1073 LOSB1072 LOSB1061 LOSB0826 LOSB1042 LOSB1069 LOSB1037 LOSB1059 LOSB1100 LOSB1100 LOSB1066 LOSB1059 LOSB1060 LOSB1060 LOSB1045 LOSB1045 LOSB1050 All Fasteners LOSB1295 LOSB1073 LOSB1059 LOSB1294 Rear Shock - Complete LOSB1064 LOSB1072 LOSB1293 Front Shock - Complete LOSB1296 LOSB1068 LOSB1298 LOSB1188 LOSB1040 LOSB1297 LOSB1292 LOSB1100 LOSB1100 LOSB1045 LOSB1027 LOSB1051 LOSB1073 LOSB1042 LOSB1187 LOSB1063 LOSB1291 LOSB1299 LOS
1/18-SCALE READY-TO-RUN MINI MONSTER TRUCK 2010 Losi, A division of Horizon Hobby, Inc. Not responsible for typographical errors. 17369 Printed 01/10 The Spektrum trademark is used with permission of Bachmann Industries, Inc. Spektrum radios and accessories are exclusively available from Horizon Hobby, Inc.
