User Manual ATS - 907 | 908 | 909 | 10 0 0 This Product should be installed according to this manual. Please read this manual carefully and install properly. Please keep this manual for future reference. Please register Warranty for proper service. Supreme... HYGIENE AND COMFORT www.LotusSeats.com Lotus Hygiene Systems Inc.
Contents 4 GENERAL CAUTIONS OPERATION (DETAILED) 10 IDENTIFICATION 14 OPERATION (BASIC) 15 OPERATION (DETAILED) 16 INSTALLATION 20 SEPERATION OF THE UNIT FROM THE TOILET BOWL 23 MAINTENANCE 24 WATER DRAINING 25 TROUBLE SHOOTING 26 SPECIFICATIONS 27 INFORMATION TO THE USER 28 29 WARRANTY Installation Manual and Operating Instructions 3 MAINTENANCE 9 INSTALLATION OPERATION (BASIC) 1000 8 OPERATION IDENTIFICATION 907 -908 - 909 6 OPERATION CAUTIONS BEFORE INSTALLATION PRE
1 IMPORTANT SAFEGUARDS/GENERAL CAUTIONS READ ALL INSTRUCTIONS BEFORE INSTALLATION AND USE The following terms are used in this manual to indicate hazards of varying degrees of severity PREPARATION DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates potentially hazardous situation which, if not avoided, could result in death or serious injury.
Do not plug in the power cord before connecting the water supply hose. Prohibited PREPARATION This product must be grounded before use. Refer to the grounding instructions on page 7. A Ground Fault Circuit Interrupt (GFCI) outlet is highly recommended. Grounding Do not splash water on this product. Please provide adequate ventilation to avoid damage to electronic components due to high levels of humidity. Do not spray water Do not touch the power cord with wet hands.
CAUTION Never operate this product if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to a service center for examination and repair Prohibited Prohibited PREPARATION Do not stand or sit on the seat cover lid. Prohibited Prohibited Do not obstruct or put anything into the dry air outlet. Do not apply excessive force to the nozzle. Allow the seat and lid to close automatically. Do not force the seat and lid.
GROUND INSTRUCTIONS (1) This product has a three-prong grounding plug, which must be plugged into an outlet that is (2) This product is for use on a nominal 120V circuit, and has a grounding plug that looks like the plug illustrated in sketch A in Figure 1. A temporary adapter, which looks like the adapter illustrated in sketches B and C, may be used to connect this plug to a 2-pole receptacle as shown in sketch B if a properly grounded outlet is not available.
3 IDENTIFICATION 1 MAIN UNIT 907 -908 - 909 PREPARATION Warning Label (Caution Label) WASH LADY Lid Control Panel Operation LED Window Deodorizer (ATS-909L/R) Dryer Outlet WASH LADY Drain / Unit Separation Button Digital Occupied Sensor (Seat Sensor) Heated Seat 2 IN THE BOX Washer (2 pcs) Water Supply Tube to SHS unit (SMART HYGIENE SEAT) T- Valve Plastic Nut to Water Tank Mounting Bolts 2 pcs Cone Packing (2 pcs) Deodorizer Filter (Only ATS-909L/R) Deodorant (Only ATS-909L/R) User Opera
4 OPERATION (BASIC) Stop all operations Wash (Anal Wash) Lady (Vaginal Wash) 907 -908 - 909 OPERATION Warm Air Dryer Nozzle move back and forth Rhythm wash Adjust the oscillation function and nozzle position (5 levels). Adjust the water pressure air dryer temperature. Adjust the water seat temperature (3 levels). Energy Saving mode. After an extended wash, allow about three minutes for water to reheat.
5 OPERATION (DETAILED) 1 PREPARATION Check for any water leaks. Plug the unit into the proper power source and the RED LED power light will start flashing. Wait until the RED LED power light stops flashing and becomes solid red. The water tank will be filled after pushing a “Wash” ( or )button. When the water tank is filling the buzzer ”Beeps”continuously, after the water tank is full the buzzer will end with “One Solid Beep”.
WARM AIR DRYER Press “Dry( ) ”, to turn on dryer. Adjust the warm air temperature with ) ” and “Low ( ) ” button. The dryer automatically stop in 3 minutes. “High ( Warmer Cooler WATER PRESSURE / DRYER TEMPERATURE ADJUSTMENT OPERATION 907 -908 - 909 After sitting down on the seat, the LED lamp( ) for water pressure should light at 3 levels( ). You can adjust the water pressure with “High( )” and “Low( )” button. Adjust the “Warm Air Dryer” temperature with “High ( )” and “Low ( )” button.
5 OPERATION (DETAILED) NOZZLE POSITION ADJUSTMENT Nozzle position is adjustable to the desired position by pressing “( “( )”button. After use the nozzle will return to position 3. )” or DEODORIZER (ATS-909L, R Only) 907 -908 - 909 OPERATION The deodorizer is activated when the unit is occupied. It automatically stops in about 1 minute after user leaves. The deodorized air velocity can be adjusted to the desired level by holding “STOP”( ) button down, and pressing “WATER”( ), simultaneously.
MASSAGE (Rhythm Wash) In using “WASH” or “LADY” mode, pressing “MASSAGE“button will provide pulsating spray. In addition, the water pressure can be adjusted by pushing "( ) High or ( Low" and "MASSAGE", simultaneously. ) * Auto-Setting of Massage : Without occupying the seat, press “MASSAGE” button for 3 seconds to set up Auto-Setting of “MASSAGE”. After set up the “MASSAGE” function will operate Automatically in CLEANSING mode.
3 IDENTIFICATION (ATS-1000) 1 MAIN UNIT 1000 PREPARATION Wash Warning Label (Caution Label) Lady Lid Simpe Operation Panel Operation LED Window Deodorizer (ATS-1000L/R) Dryer Outlet Wash Lady Drain / Unit Separation Button Digital Occupied Sensor (Seat Sensor) Heated Seat 2 IN THE BOX Washer (2 pcs) T-Valve Mounting Bolts 2 pcs Base plate (1 pc) 14 Deodorizer Filter Unit Cone Packing (2 pcs) Water Supply Tube to SHS unit (SMART HYGIENE SEAT) DEODORANT Remote control Nuts (2 pcs) Insta
4 OPERATION (BASIC) STOP WASH LADY WASH LADY PURE STREAM DRYER DRYER 1000 OPERATION SEAT HIGH Adjust the water and seat temperature (4 levels). OSCILLATE MASSAGE Adjust the oscillation function and nozzle position (5 levels). WATER Adjust the water pressure and warm air dryer temperature. LOW ENERGY SAVER Energy Saving mode Simple Operation Panel STOP WASH LADY When you sit on the unit, please sit down on the central position in order to activate the sensor.
5 OPERATION (DETAILED) 1 PREPARATION Check for any water leaks. Plug the unit into the proper power source and the RED LED power light will start flashing. Wait until the RED LED power light stops flashing and becomes solid red. The water tank will be filled after pushing a “Wash” ( operation panel. )button on the simple When the water tank is filling the buzzer ”Beeps”continuously, after the water tank is full the buzzer will end with “One Solid Beep”.
WARM AIR DRYER Press “Dry( ) ”, to turn on dryer. Adjust the warm air temperature with ) ” and “Low ( ) ” button. The dryer automatically stop in 3 minutes. “High ( Warmer Cooler WATER PRESSURE / DRYER TEMPERATURE ADJUSTMENT OPERATION 1000 After sitting down on the seat, the LED lamp( ) for water pressure should light at 3 levels( ). You can adjust the water pressure with “High( )” and “Low( )” button. Adjust the “Warm Air Dryer” temperature with “High ( )” and “Low ( )” button.
5 OPERATION (DETAILED) NOZZLE POSITION ADJUSTMENT Nozzle position is adjustable to the desired position by pressing “( “( )”button. After use the nozzle will return to position 3. )” or DEODORIZER (ATS-1000L, R Only) The deodorizer is activated when the unit is occupied. It automatically stops in about 1 minute after user leaves. The deodorized air velocity can be adjusted to the desired level by holding “STOP”( ) button down, and pressing “WATER”( ), simultaneously.
MASSAGE (Rhythm Wash) In using “WASH ( )” or “LADY ( )” mode, pressing “MASSAGE“button will provide pulsating spray. In addition, the water pressure can be adjusted by pushing "( ) High or ( ) Low" and "MASSAGE", simultaneously. * Auto-Setting of Massage : Without occupying the seat, press “MASSAGE” button for 3 seconds to set up Auto-Setting of “MASSAGE”. After set up the “MASSAGE” function will operate Automatically in CLEANSING mode.
6 INSTALLATION CAUTION BEFORE INSTALLATION Please, do not plug in before installation. If you need an electric power outlet or extension, please consult a qualified electrician. STEPS 1 Shut off water supply then flush toilet. Remove the water supply hose to toilet tank (Part A). 2 Connect T-Valve. Install T-Valve as shown. A Thread from tank INSTALLATION Existing Flexible Tube (The water supply hose) Use the Spanner T-VALVE Use the Spanner 3 Connect Water supply hose to the T-Valve.
5 Put the BOLT into METAL BOLT CASE and align with the top of the BASE PLATE. Insert BOLT with METAL BOLT CASE onto the BASE PLATE. Metal Bolt Case Bolt Bolt Metal Bolt Case Base plate DO NOT MOUNT Base Plate to toilet bowl. Follow step 6. 6 Flip the base plate with bolt/metal bolt case upside-down and slide into the grooves at the bottom of the unit, slide until it snaps in place. 7 Install the main unit and insert the mounting bolts to the toilet mounting holes.
6 10 INSTALLATION Insert the deodorant catalyst into the unit. (ATS-909L/R, ATS-1000L/R) Deodorant . Deodorant case Cover Put together the deodorant package as shown. Insert the deodorant case into the unit. 6 INSTALLATION - FIRST TIME SETUP 2 1 INSTALLATION Reset Test Turn on water valve. 3 Plug into power outlet.
5 SEAT 6 12 9 3 WATER 6 Once the water tank is full, push the water and seat temperature button to red LED. 7 Please wait five minutes and once you feel the seat/water is hot then the unit is ready to be adjusted to your desired temperature SEPARATION OF UNIT FROM THE TOILET BOWL In case you need to remove the SHS unit from the toilet bowl, follow these steps. 1 2 Disconnect the power plug 3 Push and hold the button on the right side of the unit to completely drain the water from water tank.
8 MAINTENANCE CLEANING THE NOZZLE In case the nozzle is soiled and needs to be cleaned, press “WASH”( ) button for 3 seconds without occupying the seat, the nozzle will extend out without spraying water. After cleaning, Press “STOP”( retract nozzle. * For ATS-1000 model use , ) button to . CLEANING THE BODY OF UNIT When you clean the body, do not use “thinner”, “benzene” or “NaClO”. It causes defects to the surface of unit. Please use a damp cloth when you clean the unit.
9 WATER DRAINING DRAIN THE WARM WATER TANK IN THE UNIT If you are going to leave the unit unused for a long time, please drain water from the unit’s warm water tank. 1) Disconnect the power plug. Existing Flexible Tube (The water supply hose) 2) Close the shut off valve. 3) Press and hold the drain button until the water is completely drained from the unit’s water tank. 4) To re-supply water after draining, open the shut off valve.
10 TROUBLE SHOOTING Trouble MAINTENANCE 26 Cause Remedy The water does not spray 1. The water tank is not filled. 2. The shutoff valve is closed. 3. Freezing inside the main unit or the water supply pipe. 1. Wait about one minute. 2. Press the desired washing button once again. 3. Turn on the shutoff valve to open. 4. Heat the room (for about two hours). Operating the unit while parts are frozen will cause a malfunction. The unit is not operating 1. Disconnected the power cord. 2.
11 SPECIFICATIONS Specifications ATS-907 Power Rating ATS-908 ATS-909 AC 120V 60Hz 660W Type Direct Inlet flow type Water inlet pressure 0.4 ~ 7.5 kgf/cm2(5.69 psi ~ 106.7psi) Water inlet type Power cord Wash Device ATS-1000 1.2m (4 feet) WASH Max. 1.2ℓ/min ( Max. 0.32 GPM) LADY Max. 1.2ℓ/min ( Max. 0.32 GPM) Water Pressure Adjustable 5 Levels Room Temp - 40°C (Room Temp.
12 INFORMATION TO THE USER This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This Warranty does not cover the following 1. Defects and/or malfunctions from failure to properly install, operate and/or maintain the unitin accordance with the installation manual. 2. Damage from abuse, fire, flood, freeze, and any other acts of Nature. 3. Damage resulting from unauthorized alterations, attachments and/or repairs. 4. If the product was not installed properly to residential water closets. 5. Damage from installing the unit in an environment with animals, mice or insects. 6.
1.877.808.0055 www.LotusSeats.com Inquiries and Support Lotus Hygiene Systems Inc. 1621 E. St. Andrew Pl., Santa Ana, CA 92705 1.877.808.0055 www.LotusSeats.
