LWX-1 WEATHER Satellite Weather Radio Module Installation Instructions 988-0158-13A
Copyright © 2009 Navico All rights reserved. No part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Lowrance Electronics. Lowrance® is a registered trademark of Navico. Navico may find it necessary to change or end our policies, regulations and special offers at any time. We reserve the right to do so without notice. All features and specifications subject to change without notice.
This document covers the installation and status/diagnostic indicators available for the Lowrance LWX-1. It also details how to activate a SIRIUS subscription. LWX-1 package include: Main Components: 1. Antenna Receiver (AR) pre-configured for a mast mount • AR Interconnect Cable (attached to AR) connects to IM 2. Interface Module (IM) • IM Power Cable (attached to IM) connects to Vessel power • IM Network Cable (attached to IM) connects to ChartPlotter Mounting Components: 1. AR Gasket (1) 2.
LWX-1 Installation Options The LWX-1 can be mounted in three basic configurations: 1. AR Mast Mount (factory-installed option) 2. A R Flush Mount with cable routed through the mounting surface (e.g. deck) 3.
1. AR Mast Mount Installation The LWX-1 AR is shipped in the retail box factory-configured for a mast mount. To use AR Mast Mount Installation: 1. L oosen the four AR Bolts & Nuts (a couple of counter-clockwise turns on each). 2. The AR Mast Boot will loosen, allowing the AR Mast Mount to turn. 3. I nsert the AR Interconnect Cable into the Antenna Mount and route it carefully to the Interface Module (IM).
2. AR Flush Mount Installation (through deck) AR Flush Mount with cable routed through the deck. To use AR Flush Mount through-deck installation: 1. R emove the four AR Bolts & Nuts (the AR Cover and AR Base are factory fitted – DO NOT ATTEMPT TO SEPARATE THEM) 2. U se the AR Gasket as a template to mark where the AR Mounting Screws and AR Interconnect Cable holes are to be pre-drilled 3.
3. AR Flush Mount Installation (above deck) In this AR Flush Mount installation, the cable is routed out the back of the LWX-1. This installation is the same as AR Flush Mount through-deck Installation, except the AR Interconnect Cable is routed under the LWX-1 and out the back above the deck instead of through the deck. To use AR Flush Mount above-deck installation: 1. W ith a pair of needle-nose pliers, break away and remove the AR Channel Stop 2.
IM Installation With all of the AR installation options, it is recommended that the IM is mounted/ installed below deck. To install the IM: 1. O pen the IM enclosure by unscrewing the two IM Enclosure Screws on the front panel 2. I nsert the male RJ45 connector on the end of the AR Interconnect Cable into the female RJ45 connector in the middle of the inside of the IM enclosure. The RJ45 connector will click into place when it is connected correctly 3.
LWX-1 Status Indicators The LWX-1 status indicators are the two LEDs on the Interface Module. The IM indicators are to be used to obtain connectivity with the end-user device, where more detailed problem diagnosis is available. Power LED indicates LWX-1 Power: 1. LED OFF — No power to the Interface Module 2. LED ON (solid green) — Power to Interface Module Status LED indicates LWX-1 Status: 1.
If LED blinks ON/OFF three times during the power-up cycle and then turns OFF, an Ethernet loop back connector should be connected to the IM Network Cable and the LWX-1 should be power cycled. If the blinking during power-up does not recur, then the IM Network Cable is good, and the end-user device should be checked. When IM Network Cable is properly connected to the host device, the end-user can request a full LWX-1 Diagnostics Report to perform any further required diagnosis.
Signal strength, ESN and antenna status are shown on the SIRIUS status screen Your ESN is also shown on the label attached to the LWX-1 carton To activate a SIRIUS subscription: 1. A fter the LWX-1 module is installed, locate the label on the front flap of the LWX-1 carton 2. R ecord your ESN number (SIRIUS ID) and contact SIRIUS at 1-800869-5480. SIRIUS Marine Weather service can only be activated by phone.
LWX-1 Diagnostic Report The following information is shown in the Diagnostic Report retrievable by the Chartplotter. To view the Diagnostic report, access the SIRIUS Status screen and press MENU.
SIRIUS Module Information Name Description Example Radio Activation Status - Data Indicates the activation status of the SIRIUS Radio Module. The first value indicating an active subscription. 1 of -1 This indicates a fully activated receiver. Parameter 1 — indicates is set to ‘1’ when there are subscribed channels. Parameter 2 — provides a bit mask for the individualized, enabled and activated status indicators (counting up from bit 0). This is a hexadecimal value.
Radio Signal Strength Indicates the signal strength received by the SIRIUS Radio Module. The value is in the range of 0-3 with 3 being maximum.
NAVICO LIMITED TWO-YEAR LOWRANCE WARRANTY “We,” “our,” or “us” refers to NAVICO, the manufacturer of this Lowrance product. “You” or “your” refers to the first person who purchases this product as a consumer item for personal, family or household use. We warranty this product against defects or malfunctions in materials and workmanship, and against failure to conform to this product’s written specifications, all for two (2) years from the date of original purchase by you.
www.lowrance.com 988-0158-13A Pub.