StructureScan HD Transom mount Installation Guide ENGLISH www.bandg.com | www.simrad-yachting.com | www.lowrance.
Warning: It is your sole responsibility to install and use the instrument and transducer(s) in a manner that will not cause accidents, personal injury or property damage. Always observe safe boating practices. The choice, location, and installation of transducers and other components of the system are critical to the performance of the system as intended. If in doubt, consult your Navman dealer.
1 Installation preparation Accessories If you received this manual with a StructureScan accessory, you will notice that some information in the document does not apply to the accessory. This manual has installation instructions for your accessory, and accessory pack content tables on the back cover. Contents Your StructureScan box is packed with the StructureScan HD module, a Power cable, fuse and fuse holder, StructureScan transducer, mounting bracket, 15 foot (4.5m) ethernet cable and a hardware kit.
Mounting options The StructureScan transducer can be mounted on the transom, jackplate, step or directly to your boat’s hull. When mounting it directly to the hull, you must purchase a highquality, marine grade above- or below-waterline sealant/adhesive compound. Use the following table to determine which mounting option is best suited to your boat/installation preferences.
StructureScan HD transducer mounting options Transom mount (Page 8) K eeps transducer in the water when the boat is on plane, allowing you to track bottom at high speeds Transducer angle can be adjusted so it is parallel with the water Transducer more likely to collide with obstructions in the water and adds drag to the boat Transducer is not in the water when boat is on plane; protects transducer and prevents drag from transducer Jackplate mount (Page 9) T ransducer angle can be adjusted so it i
2 Installation Bracket and transducer assembly The StructureScan bracket comes with four washers, two bolts and two nuts. If you plan to mount the StructureScan transducer directly to the step (Step Mount) or on the trolling motor, you do not need to assemble the bracket.
Transducer angle After mounting the StructureScan transducer, make sure the transducer is adjusted so it will be parallel with the waterline when moving at trolling speed. Downscan Overlay The StructureScan transducer should be installed within approximately 1 foot of the broadband sounder transducer to get optimum performance from the Downscan Overlay feature.
Transom mount The StructureScan transducer can be mounted just like a skimmer transducer, where it is in the water when you are on plane or can be mounted so it is only in the water, when you are moving at trolling speed.
Jackplate Mount The StructureScan transducer can be mounted inside or outside of the jackplate by drilling through the jackplate and then running bolts though the hinge hole in the side of the bracket into the jackplate.
Step Mount Mounting the StructureScan transducer under the step not only protects the transducer from hitting objects in the water, but does not cause any drag on your boat when it is on plane. Step Mount Supplies (not included) 1/8” Drill bit (Transom mount pilot holes) Marine grade above- or belowwaterline sealant To use Step Mount: 1. C hoose a transducer location. 2. Route the transducer cable to the location where the StructureScan module will be installed. 3.
Direct/Step Mount (No Bracket) When using the direct mount installation shown below, you MUST turn on the Flip Left/Right feature. Refer to your Operation manual for more information.. Direct Step Mount Supplies (not included) 3/32 Drill bit (Direct/Step mount pilot holes) Marine grade above- or belowwaterline sealant To use Direct Mount: 1. Make sure the boat’s step is the same length or longer than the StructureScan transducer. 2.
2.1”(55.5mm) 10.8”(274.3mm) 2.8” (72.7mm) 10.1”(257.
StructureScan Specifications Power Requirement 12 Volts Voltage Input 10V - 17V Transmit Power WRMS: 500W WPK: 4000W Current Drain Max: .75A Inrush: 4.7A pk Typical: .60A Fuse Type External: 3A Fast Acting Automotive Blade Transducer Cable 20 feet (6m) Target Separation 1.5” (38.1mm) Transducer Frequency 455kHz Communication Ethernet Shared devices supported 3 Weight StructureScan module (1.8lbs) Transducer (1.9lbs) Transducer with bracket (2.
StructureScan LED Guide Indicator 14 | LED Status Definition Transducer LED Off Transducer not connected or cable/transducer is broken Transducer LED Green/ stays on Transducer LED Green/ flashing Power LED Off Power LED Red/stays on Product in booting process Power LED Green/stays on Product has power/operating Power LED Red/Green/ slow flashing Product in factory mode; ethernet communication working Power LED Red/Green fast flashing Product in factory mode; no ethernet communicati
StructureScan Troubleshooting Tips • StructureScan not displayed • • • ake sure StructureScan HD is powM ered Check unit software; must have at least version 2.
*988-10284-001* www.bandg.com www.simrad-yachting.com www.lowrance.
