-2-
Content ............................................................................................................................ 1. Installation Installation............................................................................................................................ ............................................................................................................................-- 6 ............................................................................ - 6 1.1.
...................................................................................... 1.3.3.2.8. P2P P2P...................................................................................... ......................................................................................-- 35 .................................................................... - 36 1.3.3.3. Channels Parameters Parameters.................................................................... ..............................................
................................................................................... - 61 5.3.1. Set Wireless Router Router................................................................................... ........................................................................................ - 63 5.3.2. Set the IP Device Device........................................................................................ ...................................................................... - 65 5.3.3.
1. Installation 1.1 1.1.. Minimum System Requirements The IP device provides access through an embedded web server. To access the device, your PC needs to meet minimum requirements to perform satisfactorily. CPU Pentinum 4 2.4GHz and above Memory 128 MB or above Windows XP with SP2 or above. Operating System Windows Vista / Windows 2003 / Win7 Internet Explorer 6.0 and above.
1.2 1.2.. Preparation IP device accesses through Internet Explorer browser. Please set up the correct IP address firstly. 1. Setup your PC network The IP address of your PC must be in the same subnet with the IP device. You need to match the TCP/IP settings with PC before you can access it via IE. 2. Setup IP device device’’s IP address The default IP address of IP device is 192.168.1.199. Default Subnet Mask is 255.255.255.
� STEP1 Start up your computer. � STEP2 Click the [Start] and select the “Control Panel” � STEP3 Select the “Network and Internet connections”.
� STEP4 Select the “Network and Sharing Center” .
� STEP6 Click the “Properties” � STEP7 Select the “Internet Protocol Version 4 (TCP/IPv4)” - 10 -
� STEP8 Select the “Use the following IP address”, enter the IP address and subnet mask. For example, you can set up your PC IP address: 192.168.1.200 � STEP9 Click the [OK] and close all the dialog windows one by one.
1.3 1.3.. Configuring the IP Device Once all preparations of PC have been done, you can login the IP device through Internet Explorer Browser 6.0 or above. Follow the procedures below to configure the IP device. � STEP1 Enter the default IP address of the IP device on Browser: http://192.168.1.199 � STEP2 Enter User name and Password. (Default user name is 888888, default password is 888888), then click “OK”.
� STEP4 Click the notice, then you will see a window message to ask for your permission to install the Active X control. Please click “Install” to install this plug-in, otherwise you cannot use our IP device. NOTE: If you can’t see the download ActiveX notification, please follow below steps: For IE browser: Click “Tool” “Internet Options” “Security” “Custom level”. Find “Download signed ActiveX controls” and check the “Enable” radio button. Click “OK” button then restart the IE.
1.3.1 1.3.1.. Real-time 1.3.1.1. Video Control Click “Play” button, to view real-time video Click “Stop” button, to stop watching the video.
1.3.1.2. Pan/Tilt Operation Click the right buttons to control the rotation from Up, Down, Left, Right and auto rotation. 1.3.1.3. Quick Operation These three buttons are shortcuts for setting the IP device, which are directed to “Settings” interface of IP device. 1.3.1.4.
1.3.1.5. Real-time Video Function Audio 【Audio Audio】Click “Audio” button, the button icon will become orange. Connect a pickup with the IP device correctly, you will be able to hear the sound from the IP device via your computer. Please refer to the following chapter to set the audio parameters: 1.3.3.3.5 Audio Parameters 【 Talkback 】 Click “Talkback” button, the button icon will become orange.
Record 【Record Record】Click “Record” button, the button icon will become orange, recording starts. Click the “Record” button to stop recording, the icon turns back to be white. The IP device will create automatically a folder named by the current recording date, and save the recorded file in the format of *.mp4.in Disk D. The recorded file is named with: Device name_1_time. For example: D:\20110305\video server_1_092637.mp4”.
1.3.2 1.3.2.. Replay This interface is to replay the video. Click “Replay” to enter. When your first time to enter this interface, there is an adding-on Active X control notices to display on Internet Explorer. Please click “Install” to install this plug-in, otherwise you cannot view the replay.
1.3.2.1. Query Date Select the recording time to replay, click “Search”, there will display the file list in the segment time under the “File List”. 1.3.2.2. File List Choose the one you want to replay and click matching icon - 19 - to playback.
1.3.2.3. Play Toolbar Progress bar 【Progress bar】Click in the progress bar to show the current broadcasting schedule, and adjust the broadcasting pace. Play the recording. Suspended play. Stop play. Per click “Step”, the playback will play only a frame recording. For example, one second NTSC recording is composed by 30 frames pictures, then you need to click ”Step” 30 times to jump to next second. To make playback speeds faster. To make playback speeds slower.
1.3.3 1.3.3.. Settings 1.3.3.1 1.3.3.1.. Basic Parameters 1.3.3.1.1. Device Name Device Name 【Device Name】Input the name of the device, then click OK to save. You can modify the name. Device name usually displays in the recording files name and snapshot file name, to distinguish other videos. The device name won’t display in the “Real –time” windows. Serial Number 【Serial Number】Serial number of current IP device , which cannot be changed. 1.3.3.1.2.
� STEP1 Click “Edit” to modify the time, � STEP2 Click “OK” to finish the modification. If you want to have the IP device time the same with the PC time. Please click the “PC Time” and then click “OK” to finish. 1.3.3.1.3 1.3.3.1.3.. User Management Default Admin User name/Pwd is: 888888/888888. You can modify them here, then click “OK” button. This modification requires logging in the webpage again to browse real-time video. The Common User Name 1&2 / Pwd 1&2 is 1/2 separately.
1.3.3.1.4 1.3.3.1.4.. Time to Reboot This function is used for rebooting the IP device as long as the power is on. Keep the “Timing to Reboot” “On” status, set the “Reboot Time”, for example, set “1H5M”, that is to say, the IP device will reboot on 01:05 every day as long as the power is on. 1.3.3.1.5 1.3.3.1.5..
1.3.3.1.6 1.3.3.1.6.. System Update This is used for system upgrade. Click “Browse…”to choose upgrade files of “*. itm” format, and then click “OK”, until the webpage displays “The program has been updated successfully, please login again”, the device will reboot automatically. Upgrade files are provided from your supplier. This is very important and pivotal, we don't recommend the system upgrade unless you have got the particular guide from your supplier. 1.3.3.2 1.3.3.2..
1.3.3.2.1 1.3.3.2.1.. IP Address & Port To access the IP device via WAN, you must map the ports first, please refer to: 5.2 Mapping & Access IP Device via WAN Connection type 【Connection type】Static IP Address, PPPOE, DHCP optional. � Static IP Address, this method is highly recommended.
� DHCP The following parameters please keep the default or follow our instruction. WEB Port 【WEB Port】Default is 80. If you change into another port, you need to add this port behind IP address when visit the IP device via IE. For example, IP device is 192.168.1.199, web port is 81, and then the login IP address is http://192.168.1.199:81. If you want to visit from WAN (Wide Area Network) via IE, you must map the WEB port on your router equipment. Date Transfer Port 【Date Port】Default is 3000.
NOTE: when you change the above parameters, you must click on the upper left corner “Save” and “Reboot” to take effect. 1.3.3.2.2 1.3.3.2.2.. WIFI Parameters You need a wireless router of 802.11b/g before you use the WiFi function, please setup the SSID name and Encryption of Wireless Network in your wireless router. Wireless Network 【Wireless Network】Click “Refresh” to find the SSID name and Encryption you have set in the “Wireless Network”.
There are three methods to enable WIFI function: Static IP Address/PPPOE/DHCP. � Static IP Address � PPPOE If you choose to PPPOE, please contact your network operators, to provide the “PPPOE User Name” and “PPPOE Password"” � DHCP The following parameters will keep the same under these three methods.
1.3.3.2. 3. DDNS 1.3.3.2.3. DDNS (Dynamic DNS) is simply a way of using a static hostname to connect to a dynamic IP address. When connected to your ISP, you are assigned a temporary IP address. DDNS services keep track of your IP address and route your Domain name to that address when you wish to connect to the IP device from a remote location.
1.3.3.2. 4. FTP Parameters 1.3.3.2.4. This function is used for uploading the files to FTP server. You must have an FTP server, if you don't have, you cannot use this function. FTP User Name 【FTP Name】Default is 888888, please change into your own FTP server User Name. FTP Password 【FTP Password】Default is 888888, please change into your own FTP server Password. FTP Host IP 【FTP IP】Default is 192.168.1.40, please change into your own FTP server landing IP address.
1.3.3.2. 5. FTP Scheduled Record 1.3.3.2.5. This function is used for automatically uploading the recording to the FTP server according to the schedule. Please set the schedule first. � How to upload recording to FTP Server: STEP1 Built a FTP server, set up the user name, password, FTP server IP and port. � STEP2 Fill in your FTP parameters in the IP device. Click OK. � STEP3 Setting FTP scheduled recording.
� STEP4 You can see the similar video on the FTP server.
1.3.3.2. 6. UPNP 1.3.3.2.6. UPNP is a quick way to discover the IP device on the network. Via UPNP function, the above ports could be mapped automatically in the router. External IP Address: WAN IP address of the router. How to use UPNP function: � STEP1 Please enable the UPNP function both on the IP device and router. (Please note that not all routers support this function. Refer to your router manual for further details). The IP device will map automatically.
� STEP STEP22 If “State” display “Mapped”, means UPNP settings is successful, please refer to the above picture. Then, please follow the below procedures to access the IP device via WAN: http://External IP Address:Web Port. If External IP is: 119.145.0.165 and Web Port is 80.The address is: http://119.145.0.165:80 NOTE: The router must support UPNP and keep “On” state.
1.3.3.2. 8. P2P 1.3.3.2.8. This function is very important for mobile monitoring. For details of mobile monitor, please refer to the “Mobile Monitor Operation Manual” in the CD: Enable P2P 【Enable P2P】Enabled or disabled P2P。 Message port 【Message port】The default is 4602. After you setting the UPNP, this port will be automatically mapped out.
1.3.3.3 1.3.3.3.. Channels Parameters 1.3.3.3.1 1.3.3.3.1.. Character Superposition 【 Channel Name 】 To distinguish different equipment. But it won't show in preview screen. Keep the default. Time Type 【Time Type】 Choose the time type from the four formats. Frame Rate 【Frame Rate】Including “Not indicating” and “indicating”. Choose “indicating”, the real-time screen will display the Bit Rate, if choose “not indicating”, will not display the Bit Rate.
1.3.3.3.2 1.3.3.3.2.. Video Coding Network Transfer Stream 【Network Stream】This is a main stream of IP device. This stream is used for IE View. � Resolution——Five image resolutions available: 704X576 (D1), 704 x 288(2CIF), 352 x 288(CIF), 176 x 144(QCIF),320 x 240(QVGA) � Bite Rate Type——“Constant” and “Variable”. If you choose “Constant”, it ensures transmission fluency. If you choose “Variable”, it ensures the steady image quality. Constant is recommended. � MAX.
� Key Frame Interval—— keep the default. � Compression——H.264 and MJPEG optional. NOTE: Save and reboot is a must after change. Server-end Storage Stream 【Server-end Stream】This is used for SD card storage stream setting. 【 Mobile Watching Stream Stream】 This is the mobile phone transmission streaming. Please keep the default. 1.3.3.3.3 1.3.3.3.3.. Adjust Color Brightness 【Brightness Brightness】Brightness adjustment. Contrast 【Contrast Contrast】Contrast adjustment.
1.3.3.3.4 1.3.3.3.4.. Area Shield This function is used for privacy shield protection. You can set total 4 areas. Area 【Area Area】The default Area 1 icon is green, but without any privacy shield area setting . Please enable the “Area Shield On-off”, Left click in the video on the left side, hold on and move, release the mouse to finish the shield for Area 1. The same operation for Area 2 and the others: setting the shield area, then click the Area 2. Click OK to save.
1.3.3.4 1.3.3.4.. Alarm Parameters 1.3.3.4.1 1.3.3.4.1.. Sensor Detection Schedule Settings This function is used for setting the sensor detection Schedule. To use this function, please connect alarm sensor to the IP device. If you want to upload sensor detection recording file of IP device on Monday 0:10 AM, and stop upload on 23: 59 PM. You can set according to above.
1.3.3.4. 2. Motion Detection Area Settings 1.3.3.4.2. Sensibility Adjusting 【Sensibility Adjusting】Sensitivity adjustment. 1 to 99 Adjustable. Suggest to use the default parameters, if sensitivity adjustment is too higher, which can cause unnecessary alarm. Left click the real-time area and move to choose the motion detection area. � Select full Screen Choose full Screen for motion detection area, click OK. � Clear All Clear all the motion detecting area. Click OK.
1.3.3.4. 3. Motion Detection Schedule Settings 1.3.3.4.3. This function is used for setting the motion detection Schedule. To use this function, please connect an alarm sensor to the IP device. If you want to upload motion detection recording file of IP device on Monday 0:10 AM, and stop upload on 23: 59 PM. You can set according to above. Start Sensor Detection 【Start Detection】Enable or disable sensor detecting.
1.3.3.4. 4. Camera Been Shaded Alarm Trigger Schedule Settings 1.3.3.4.4. When the IP device is shaded, there will alarm in the CMS via this function. Camera Been Shaded Detection 【Camera Detection】Please enable this function before setting. Triggering Alarm Output 【Triggering Output】Please enable this function before setting Sensibility 【Sensibility Sensibility】 】Sensitivity adjustment. 1 to 5 Adjustable.
Se nd Email If There Are Alarm 【Se Send Alarm】 “On” and “Off” optional Priority 【Priority Priority】Default is 0. User Name 【User Name】User name of email box. Password 【Password Password】Password of email box Mail Server IP 【Mail IP】Mail Server IP(SMTP) Mail Server Port 【Mail Port】SMTP Server Port. Sender's Name 【Sender's Name】Sender’s name Sender's Email 【Sender's Email】Sender’s email address Receiver's Name 【Receiver's Name】Receiver’s name Receiver's Email 【Receiver's Email】You can fill in three mail box.
� STEP4 Click “Test” button to test all parameters. If all are correct, email alarm will be triggered by motion detection. NOTE : There is no request for Receiver's Email as long as it is valid. But the Sender's Email must be able to receive email via software like foxmail or outlook. The best choice is the tariff email box.
1.3.3.5. Server Storage 1.3.3.5.1. Server-end Timing to Record This IP device supports SD card to store the recording, the max capacity is 32GB. Here you can set the time of video recorded to the SD card. Please enable the timing recording first. 1.3.3.5.2. Server-end Timing to Snapshot In this function, you can set the snapshot parameters.
Snapshot Time Interval 【Snapshot Interval】Please set the snapshot time interval, from 10-3600 seconds. Start Timing Snapshot 【Start Snapshot】Please choose the time to activate the snapshot FTP Upload after Snapshot 【FTP Snapshot】Please refer to the chapter 1.3.3.2.3 FTP Parameters 1.3.3.5.3. Server-end Snapshot Parameters You could set the image quality and format of the snapshot. Snapshot Image Quality 【Snapshot Quality】From 1-100,the higher the numerical volume is, the higher the image quality is.
1.3.3.5.4 1.3.3.5.4.. Server-end Storage Device Cut off the power, insert the SD card, click “Format”, then reboot and login in the IP device, there will display the info of the SD card in this interface, then you can use SD card function now.
2. Specifications Hardware Compression H.264 CPU: HI3512 FLASH: 8M DRAM: 32M System: Built-in Linux Resolution: D1,CIF Motion detection: Yes Watermark video: Yes Audio Compression Format: G.
3.
4. Frequent Asked Questions 4.1 4.1.. Fail to Access the IP Device Through the Browser � Possible Cause: The network is disconnected? Solution: Connect PC to the network to test whether the network access can work normally. Firstly clear the cable fault and the network fault caused by PC virus till Ping the network between PCs successfully. � Possible Cause: IP address is occupied by other equipment. Solution: Disconnect the IP device and network, and then connect the IP device to the PC solely.
4.2 .Can Not Play Video After Program Updating � Solution: Close all the browser pages; search “NetViewX Control.cab” file under the C:\Windows\Downloaded and delete it. Then connect the IP device by the browser again, the IP device real-time view will automatically display after install the plug-in again. 4.3 4.3.. Fail to Browse Images Normally in Windows98 � Solution: Install the DirecteX8.0 or higher version. Update the IE Explore to 6 and above versions. 4.
required inside switch. � If the IP device never be recognized when configuring the firewall rule of switch, it’s necessary to allow the communication on ports 3000, 3001, 3002, 3003 and 80 for the IP device. Otherwise, any data packet will be filtered and can’t reach target. 5. Errors Occur After Updating 4. 4.5. Delete the buffer of the browser.
5. Appendix 1. Hardware Reset 5. 5.1. After updating the IP device, or when there are some problems that you can’t solve via reboot, for example, you can’t get the IP address via the search tool, please try to reset the IP device. After this reset, all the parameters will be back to the factory default, the IP address will be back to default: 192.168.1.199.
192.168.1.199; If not, it means the reset is failed, please reset again. 5.2 5.2.. Mapping & Access IP Device via WAN Access IP device via WAN is a very important network function, using this function, you can access your IP device anywhere anytime. To access the IP device via WAN, you must map some related ports to the WAN via router. These ports are: Web Port, Data Transfer Port, Data Control Port, Remote Transfer Port and Message Port.
WEB Port 【WEB Port】 Default is 80. It is a very important port to recognize the IP device. This 80 web port is dropped acquiescently, for example, if the IP address of your IP device in LAN is 192.168.1.199:80, the default IP address will be 192.168.1.199. If the web port is changed into other, it can’t be dropped. For example, if the port is changed into 81, t he LAN IP address will be 192.168.1.199:81 。 In the same way, the WAN IP address will follow this rule, too.
Message Port 【Message Port】 Default is 4602, for mobile monitor NOTE: If you don't map this port, you won’t access the IP device via the mobile phone. There are two methods to finish the mapping: 1.
mapping. 5.2.1 5.2.1.. UPNP Mapping UPNP is a quick way to discover the IP device on the network. Via UPNP function, the above ports could be mapped automatically in the router. Please refer to the chapter:1.3.3.2.6 UPNP 2. Manual Mapping 5.2. 5.2.2. Via manual mapping, you have to map the ports in the router by yourself. Different routers have different interfaces and methods. Take Cisco LINKSYS WRT54G2 for example.
� Step 2 Check the Status and access Access to the “Status” to check the WAN IP address. If the WAN IP address is 119.145.0.165, the IP address of the IP device will be http://119.145.0.165:80 or http://119.145.0.165 when you access via WAN.
- 60 -
5.3 5.3.. Wireless Settings WIFI function is a powerful function that makes your IP device getting out of the limit of network cable in a certain distance. You can put your IP device anywhere with an adapter in this distance, and access it freely. First, you have to have a wireless router to work with the wireless IP device. Set the wireless network of the router before using. Different routers have different interfaces and setting methods. Take Cisco LINKSYS WRT54G2 wireless router for example. 5.3.1.
� Step 2 Set Wireless Security Security Mode: Select “WPA2 Personal” WPA Shared Key Key: Set this key freely and remember it. For example: 33265782 Please keep the other settings to be defaults. Then save these settings via “Save settings”, and close the router. Login the router again.
5.3.2.
Login the IP device via Internet Explorer, access to the “Setting Setting”” � Network Parameters WIFI Parameters “Network Parameters”� “WIFI Parameters”, � � Refresh Step 1 Press “Refresh Refresh” to search the SSID and the Encryption Type Step 2 Fill in the following info: Currently Wireless Network Network: kf, the SSID Input Password Password: 33265782, the “WPA Shared Key” � Step 3 then go to the “IP Address Configuration” There are three methods to achieve the wireless function: Static IP Address/PPPO
� � � � � DHCP, this is the easiest way to use WIFI function. WIFI Gateway as Default Gateway Step 4 Enable the “WIFI Gateway” WIFI specification Step 5 Select the “WIFI specification”: 802.11b&802.11g OK Step 6 Click “OK OK” Step 7 Save and reboot the IP device 5.3.3.
- 66 -
5.4. How to Use the Streaming Protocol These two streaming protocols are for higher requirement users and broadcasting clients. VLC player is necessary for this function, the following guide is based on the latest version of: VLC media player 1.1.7. 【 RTSP 】 RTSP is Real-Time Streaming Protocol, to transfer the multimedia audio and video streaming. This function is for higher requirement users or Broadcasting clients only.
� STEP2 Use the players which support the RTSP function to play the streaming. For example: use VLC player to play the RTSP streaming. Here it is the method to use the VLC player: Install the public VLC player software from the internet.
The RTSP address is: rtsp:// 192.168.1.199:554/0/1:1/main, formed as below: 192.168.1.199: IP address of the IP device 554: RTSP listen port 0: Default port, cannot be changed 1:1: Common User name & password, Please refer to:1.3.3.1.3 User Management main: Main streaming, In summary, the RTSP streaming is for main streaming of the rtsp://192.168.1.199:554/0/1:1/main. If you want to view sub streaming or third streaming RTSP, please follow the below format to visit. Sub streaming: rtsp://192.168.
【 TS 】 TS is transfer streaming. It is an audio, video and data communications transmission protocol that is specified in MPEG-2 Part 1. The transport stream allows for multiplexing of the digital video and audio. This function is for higher requirement user or Broadcasting clients only. How to view the video of IP device by TS? � STEP1 Enable TS, and keep the following default of the two parameters. � STEP2 Fill in the correct destination address.
- 71 -