Owner manual

ManualsBrandsLT Security ManualsVideo surveillance systemsLTN7600 Series NVR (V2.2.3)

User Manual of DS-9600/8600/7700/7600 Series NVR

User Manual of LTN7700/7600 Series NVR

Version 2.2.3

Summary of content (205 pages)

PAGE 1
User Manual of DS-9600/8600/7700/7600 Series NVR User Manual of LTN7700/7600 Series NVR Version 2.2.
PAGE 2
User Manual of DS-9600/8600/7700/7600 Series NVR Regulatory information FCC information FCC compliance : This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PAGE 3
User Manual of DS-9600/8600/7700/7600 Series NVR Preventive and Cautionary Tips Before connecting and operating your device, please be advised of the following tips: • • • • • Ensure unit is installed in a well-ventilated, dust-free environment. Unit is designed for indoor use only. Keep all liquids away from the device. Ensure environmental conditions meet factory specifications. Ensure unit is properly secured to a rack or shelf.
PAGE 4
User Manual of DS-9600/8600/7700/7600 Series NVR Product Key Features General       Connectable to network cameras, network dome and DVS. Connectable to the third-party network cameras like AXIS, ONVIF, PANASONIC, PSIA, SAMSUNG and SANYO. PAL/NTSC adaptive video inputs. Each channel supports dual-stream. Up to 32 network cameras can be connected for LTN7732 and LTN7732-P8 series NVR, 16 network cameras for LTN7616, and 8 network cameras for LTN7608-P4 and LTN7608-P8 models.
PAGE 5
User Manual of DS-9600/8600/7700/7600 Series NVR                Backup    Multiple recording types: manual, normal, alarm, motion, motion | alarm, motion & alarm. 8 recording time periods with separated recording types. Pre-record and post-record for alarm, motion detection for recording, and pre-record time for schedule and manual recording. Searching record files and captured pictures by events (alarm input/motion detection).
PAGE 6
User Manual of DS-9600/8600/7700/7600 Series NVR                    configurable: multi-address, load balance, network fault tolerance, etc. 8 independent PoE network interfaces are provided for LTN7732-P8/LTN7608-P8 series, and 4 independent PoE network interfaces for LTN7604-P4 and LTN7608-P4 series. IPv6 is supported. TCP/IP protocol, PPPoE, DHCP, DNS, DDNS, NTP, SADP, SMTP, SNMP, NFS, and iSCSI are supported. TCP, UDP and RTP for unicast.
PAGE 7
User Manual of DS-9600/8600/7700/7600 Series NVR TABLE OF CONTENTS Product Key Features ...................................................................................................... 4 Chapter 1 Introduction .................................................................................................... 11 1.1 Front Panel ............................................................................................................... 12 1.2 IR Remote Control Operations............................
PAGE 8
User Manual of DS-9600/8600/7700/7600 Series NVR 5.6 Configuring Holiday Record and Capture ............................................................... 72 5.7 Configuring Redundant Recording and Capture ...................................................... 74 5.8 Configuring HDD Group for Recording and Capture .............................................. 76 5.9 Files Protection ........................................................................................................
PAGE 9
User Manual of DS-9600/8600/7700/7600 Series NVR 9.2.9 Configuring Email .................................................................................. 149 9.2.10 Configuring UPnP™ .............................................................................. 150 9.3 Checking Network Traffic...................................................................................... 153 9.4 Configuring Network Detection ............................................................................. 154 9.4.
PAGE 10
User Manual of DS-9600/8600/7700/7600 Series NVR 13.5.2 Deleting a User....................................................................................... 199 13.5.3 Editing a User......................................................................................... 199 Appendix ............................................................................................................................... 201 Glossary ...................................................................................
PAGE 11
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 1 Introduction 11
PAGE 12
User Manual of DS-9600/8600/7700/7600 Series NVR 1.1 Front Panel Figure 1. 1 LTN7732 and LTND7732-P8 Table 1. 1 Description of Control Panel Buttons No. 1 Name Status Indicators SHIFT 2 3 DVD-R/W Control Buttons Function Description POWER: the POWER indicator turns green when NVR is powered up. READY: The indicator light is green when the device is running normally. STATUS: 1.The light is green when the IR remote control is enabled; 2.
PAGE 13
User Manual of DS-9600/8600/7700/7600 Series NVR No. Name 1/MENU: 2/ABC/F1: 3/DEF/F2: Function Description Enter: The Enter button is used to confirm selection in menu mode; or used to check checkbox fields and ON/OFF switch. In playback mode, it can be used to play or pause the video. In single-frame play mode, pressing the Enter button will play the video by a single frame. And in auto sequence view mode, the buttons can be used to pause or resume auto sequence.
PAGE 14
User Manual of DS-9600/8600/7700/7600 Series NVR No. Name 5 JOG SHUTTLE Control 6 POWER ON/OFF 7 USB Interfaces Function Description input). Double press the button to switch the main and auxiliary output. Move the active selection in a menu. It will move the selection up and down. In Live View mode, it can be used to cycle through different channels. In the Playback mode, it can be used to jump 30s forward/backward in video files. In PTZ control mode, it can control the movement of the PTZ camera.
PAGE 15
User Manual of DS-9600/8600/7700/7600 Series NVR Keys 4 2/ABC/F1: 3/DEF/F2: Access the main menu interface. Enter numeral “2”; Enter letters “ABC”; The F1 button when used in a list field will select all items in the list. In PTZ Control mode, it will turn on/off PTZ light and when the image is zoomed in, the key is used to zoom out. Enter numeral “3”; Enter letters “DEF”; The F2 button is used to change the tab pages. In PTZ control mode, it zooms in the image.
PAGE 16
User Manual of DS-9600/8600/7700/7600 Series NVR In live view mode, these buttons can be used to switch channels. Enter: The Enter button is used to confirm selection in menu mode; or used to check checkbox fields and ON/OFF switch. In playback mode, it can be used to play or pause the video. In single-frame play mode, pressing the Enter button will play the video by a single frame. And in auto sequence view mode, the buttons can be used to pause or resume auto sequence.
PAGE 17
User Manual of DS-9600/8600/7700/7600 Series NVR 1.2 IR Remote Control Operations The NVR may also be controlled with the included IR remote control, shown in Figure 1. 3. Note: Batteries (2×AAA) must be installed before operation. Figure 1. 3 Remote Control The keys on the remote control closely resemble the ones on the front panel. See Figure 1. 3. Table 1. 3 Description of the Soft Keyboard Icons No. Name Description 1 POWER Power on/off the device. 2 DEV Enables/Disables Remote Control.
PAGE 18
User Manual of DS-9600/8600/7700/7600 Series NVR 8 INFO Button Reserved. 9 VOIP Button Same as the MAIN/SPOT/ZOOM- button on front panel. 10 MENU Button Same as the MENU/WIPER button on front panel. 11 PREV Button Same as the PREV/FOCUS- button on front panel. 12 DIRECTION/ENTER Buttons Same as the DIRECTION/ENTER buttons on front panel. 13 PTZ Button Same as the PTZ/IRIS- button on front panel. 14 ESC Button Same as the ESC button on front panel.
PAGE 19
User Manual of DS-9600/8600/7700/7600 Series NVR 1.3 USB Mouse Operation A regular 3-button (Left/Right/Scroll-wheel) USB mouse can also be used with this NVR. To use a USB mouse: 1. Plug USB mouse into one of the USB interfaces on the front panel of the NVR. 2. The mouse should automatically be detected. If in a rare case that the mouse is not detected, the possible reason may be that the two devices are not compatible, please refer to the recommended the device list from your provider.
PAGE 20
User Manual of DS-9600/8600/7700/7600 Series NVR 1.4 Input Method Description Figure 1. 4 Soft Keyboard Description of the buttons on the soft keyboard: Table 1.
PAGE 21
User Manual of DS-9600/8600/7700/7600 Series NVR 1.5 Rear Panel Figure 1. 5 LTN7732 Table 1. 6 Description of Rear Panel Interfaces No. 1 Item VIDEO OUT CVBS AUDIO OUT 2 VGA AUDIO OUT 3 4 5 LINE IN RS-232 Interface VGA 6 7 8 HDMI eSATA (Optional) LAN Interface Termination Switch 9 RS-485 Interface Controller Port 10 11 12 13 14 ALARM IN ALARM OUT GROUND AC 100V ~ 240V POWER USB interface Description BNC connector for video output. RCA connector for audio output.
PAGE 22
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 1. 6 LTN7732-P8 Table 1. 7 Description of Rear Panel Interfaces No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Item VIDEO OUT CVBS AUDIO OUT Description BNC connector for video output. BNC connector for audio output. This connector is synchronized with CVBS video output. VGA AUDIO OUT BNC connector for audio output. This connector is synchronized with VGA video output. LINE IN BNC connector for audio input.
PAGE 23
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 1. 7 LTN7616 Table 1. 8 Description of Rear Panel Interfaces No. 1 Item VIDEO OUT AUDIO OUT Description BNC connector for video output. BNC connector for audio output. 2 3 4 AUDIO IN RS-232 Interface BNC connector for audio input. (Also for voice talk) Connector for RS-232 devices. 5 VGA 6 7 8 HDMI USB LAN Interface RS-485 Interface DB9 connector for VGA output. Display local video output and menu. HDMI video output connector.
PAGE 24
User Manual of DS-9600/8600/7700/7600 Series NVR 100~240VAC power supply Switch for turning on/off the device. Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). 3 4 Power Supply Power Switch 5 USB Interface 6 GND Ground (needs to be connected when NVR starts up). 7 HDMI Interface 8 VGA Output 9 10 Audio In Audio Out Network Interfaces with PoE function (for LTN7600-P) HDMI video output connector. DB9 connector for VGA output.
PAGE 25
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 2 Getting Started 25
PAGE 26
User Manual of DS-9600/8600/7700/7600 Series NVR 2.1 Starting Up and Shutting Down the NVR Purpose: Proper startup and shutdown procedures are crucial to expanding the life of the NVR. Before you start: Check that the voltage of the extra power supply is the same with the NVR’s requirement, and the ground connection is working properly. Starting up the NVR: Steps: 1. Check the power supply is plugged into an electrical outlet.
PAGE 27
User Manual of DS-9600/8600/7700/7600 Series NVR Rebooting the NVR In the Shutdown menu, you can also reboot the NVR. Steps: 1. Enter the Shutdown menu by clicking Menu > Shutdown. 2. Click the Logout button to lock the NVR or the Reboot button to reboot the NVR.
PAGE 28
User Manual of DS-9600/8600/7700/7600 Series NVR 2.2 Using the Wizard for basic configuration By default, the Setup Wizard starts once the NVR has loaded, as shown in Figure 2. 2. Figure 2. 2 Start Wizard Interface Operating the Setup Wizard: 1. The Setup Wizard can walk you through some important settings of the NVR. If you don’t want to use the Setup Wizard at that moment, click the Cancel button.
PAGE 29
User Manual of DS-9600/8600/7700/7600 Series NVR 5. Click the Next button to enter the date and time settings window, as shown in Figure 2. 4. Figure 2. 4 Date and Time Settings 6. After the time settings, click Next button which takes you back to the Network Setup Wizard window, as shown in Figure 2. 5.
PAGE 30
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 2. 5 Network Configuration Note: And for LTD7732-P and LTN7600-P series NVR, the internal NIC IPv4 address should be configured for the cameras connecting to the PoE network interface of the NVR. 7. Click Next button after you configured the network parameters, which takes you to the HDD Management window, shown in Figure 2. 6. Figure 2. 6 HDD Management 8. To initialize the HDD, click the Init button.
PAGE 31
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 2. 8 Record Settings 12. Click Copy to copy the settings to other channels, as shown in Figure 2. 9. Figure 2. 9 Copy Record Settings 13. Click OK to complete the startup Setup Wizard.
PAGE 32
User Manual of DS-9600/8600/7700/7600 Series NVR 2.3 Adding and Connecting the IP Cameras 2.3.1 Adding the online IP Cameras Purpose: The main function of the NVR is to connect the network cameras and record the video got from it. So before you can get a live view or record of the video, you should add the network cameras to the connection list of the device. Before you start: Ensure the network connection is valid and correct.
PAGE 33
User Manual of DS-9600/8600/7700/7600 Series NVR 3. 2) Check the checkbox of certain cameras to be added. 3) Click Quick Add to add the camera. To add other IP cameras: 1) On the left side of the interface, you can enter the IP address, protocol, management port, user name, password and other information of the IP camera to be added. 2) Click Add to add the camera. Note: If you check the Synchronize IP Camera checkbox, the default settings of the NVR for the IP camera is applied to the added camera. 2.3.
PAGE 34
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 2. 13 Network Configuration of the Camera 2. You can edit the network information and the password of the camera. Figure 2. 14 Password Configuration of the Camera 3. Click Apply to save the settings and click OK to exit the interface.
PAGE 35
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 2. 15 Protocol Management Interface There are 10 customized protocols provided in the system, you can edit the protocol name; and choose whether to enable the sub-stream. 2. Choose the protocol type of transmission and choose the transfer protocols. Note: The protocol type and the transfer protocols must be supported by the connected network camera.
PAGE 36
User Manual of DS-9600/8600/7700/7600 Series NVR Ethernet cabling to the connected network cameras. The LTN7608-P8 and LTN7632-P8 series NVR provides 8 PoE interfaces which can connect to 8 network cameras directly; and if you disable the PoE interface, you can also connect to the online network cameras. And the PoE interface supports the Plug-and-Play function.
PAGE 37
User Manual of DS-9600/8600/7700/7600 Series NVR the parameters of the camera can’t be edited. The IP address of the camera can only be edited in the Network Configuration interface, see Chapter 9.1 Configuring General Settings for detailed information.
PAGE 38
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 3 Live View 38
PAGE 39
User Manual of DS-9600/8600/7700/7600 Series NVR 3.1 Introduction of Live View Live view shows you the video image getting from each camera in real time. The NVR automatically enters Live View mode when powered on. It is also at the very top of the menu hierarchy, thus pressing the ESC many times (depending on which menu you’re on) brings you to the Live View mode.
PAGE 40
User Manual of DS-9600/8600/7700/7600 Series NVR 3.2 Operations in Live View Mode In live view mode, there are many functions provided. The functions are listed below. • • • Single Screen: showing only one screen on the monitor. Multi-screen: showing multiple screens on the monitor simultaneously. Auto-switch: the screen is auto switched to the next one. And you must set the dwell time for each screen on the configuration menu before enabling the auto-switch. Menu>Configuration>Live View>Dwell Time.
PAGE 41
User Manual of DS-9600/8600/7700/7600 Series NVR Manually screens switch Next screen: right/down direction button. Previous screen: left/up direction button. Auto-switch Press Enter button. All-day playback Press Play button. Switch between main and aux output Press Main/Aux button. 3.2.2 Using the Mouse in Live View Table 3. 4 Mouse Operation in Live View Name Description Menu Enter the main menu of the system by right clicking the mouse.
PAGE 42
User Manual of DS-9600/8600/7700/7600 Series NVR LTN7732-P8/LTN7616/LTN7632 LTN7604-P4, LTN7608-P4, LTN7608-P8 Figure 3. 1 Right-click Menu 3.2.3 Using an Auxiliary Monitor Note: For LTN7604-P4, LTN7608-P4, LTN7608-P8 do not have an auxiliary output, the below function is not supported with it. Certain features of the Live View are also available while in an Aux monitor. These features include: • Single Screen: Switch to a full screen display of the selected camera.
PAGE 43
User Manual of DS-9600/8600/7700/7600 Series NVR 3.2.4 Quick Setting Toolbar in Live View Mode On the screen of each channel, there is a quick setting toolbar which shows when you single click the mouse in the corresponding screen. L LTN7732-P8/LTN7616/LTN7632 LTN7604-P4, LTN7608-P4, LTN7608-P8 Figure 3. 2 Quick Setting Toolbar Table 3.
PAGE 44
User Manual of DS-9600/8600/7700/7600 Series NVR Image Settings icon can be selected to enter the Image Settings menu. Figure 3. 4 Image Settings- Preset You can also choose the Customize mode to set the image parameters like brightness, contrast, saturation and hue. Figure 3. 5 Image Settings- Customize Live View Strategy can be selected to set strategy, including Real-time, Balanced, Fluency. Figure 3.
PAGE 45
User Manual of DS-9600/8600/7700/7600 Series NVR 3.3 Adjusting Live View Settings Purpose: Live View settings can be customized according to different needs. You can configure the output interface, dwell time for screen to be shown, mute or turning on the audio, the screen number for each channel, etc. Steps: 1. Enter the Live View Settings interface. Menu> Configuration> Live View Figure 3.
PAGE 46
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 3. 8 Live View- Camera Order To set the camera order: 1) Select a View mode in . 2) Select the small window, and double-click on the channel number to display the channel on the window. You can click button to start live view for all the channels and click stop all the live view. 3) Click the Apply button to save the setting.
PAGE 47
User Manual of DS-9600/8600/7700/7600 Series NVR 3.4 Channel-zero Encoding Purpose: Sometimes you need to get a remote view of many channels in real time from web browser or CMS(Client Management System) software, in order to decrease the bandwidth requirement without affecting the image quality, channel-zero encoding is supported as an option for you. Note: This function is not supported with LTN7600-P Series NVR. Steps: 1. Enter the Live View Settings interface. Menu> Configuration> Live View 2.
PAGE 48
User Manual of DS-9600/8600/7700/7600 Series NVR 3.5 User Logout Purpose: After logging out, the monitor turns to the live view mode and if you want to do some operation, you need to enter user name and password tog in again. Steps: 1. Enter the Shutdown menu. Menu>Shutdown Figure 3. 10 Shutdown 2. Click Logout. Note: After you have logged out the system, menu operation on the screen is invalid. It is required to input a user name and password to unlock the system.
PAGE 49
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 4 PTZ Controls 49
PAGE 50
User Manual of DS-9600/8600/7700/7600 Series NVR 4.1 Configuring PTZ Settings Purpose: Follow the procedure to set the parameters for PTZ. The configuring of the PTZ parameters should be done before you control the PTZ camera. Before you start: Check that the PTZ and the NVR are connected properly through RS-485 interface. Steps: 1. Enter the PTZ Settings interface. Menu >Camera> PTZ Figure 4. 1 PTZ- General 2. Choose the camera for PTZ setting in the Camera dropdown list. 3.
PAGE 51
User Manual of DS-9600/8600/7700/7600 Series NVR 4.2 Setting PTZ Presets, Patrols & Patterns Before you start: Please make sure that the presets, patrols and patterns should be supported by PTZ protocols. 4.2.1 Customizing Presets Purpose: Follow the steps to set the Preset location which you want the PTZ camera to point to when an event takes place. Steps: 1. Enter the PTZ Control interface. Menu>Camera>PTZ>More Settings Figure 4. 2 PTZ- More Settings 2.
PAGE 52
User Manual of DS-9600/8600/7700/7600 Series NVR 4.2.2 Calling Presets Purpose: This feature enables the camera to point to a specified position such as a window when an event takes place. Call preset in the PTZ setting interface: Steps: 1. Enter the PTZ Control interface. Menu>Camera>PTZ>More Settings 2. Check the round icon of Call Preset. Figure 4. 4 PTZ- Call Preset 3. Choose the preset number. Call preset in live view mode: Steps: 1.
PAGE 53
User Manual of DS-9600/8600/7700/7600 Series NVR 2. Choose Camera in the list on the menu. 3. Double click the preset in the Preset list to call it. 4.2.3 Customizing Patrols Purpose: Patrols can be set to move the PTZ to different key points and have it stay there for a set duration before moving on to the next key point. The key points are corresponding to the presets. The presets can be set following the steps above in Customizing Presets. Steps: 1. Enter the PTZ Control interface.
PAGE 54
User Manual of DS-9600/8600/7700/7600 Series NVR 5. Click OK to save the key point to the patrol. Repeat the above steps to add more key points. You can also delete all the key points by clicking the trash icon . Select a key point, then click or button to adjust the order of the key points. Figure 4. 8 KeyPoints Deletion 4.2.4 Calling Patrols Purpose: Calling a patrol makes the PTZ to move according the predefined patrol path. Calling patrol in the PTZ setting interface: Steps: 1.
PAGE 55
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 4. 9 Calling Patrol Calling patrol in live view mode: Steps: 1. Press PTZ control on the front panel or on the remote, or click PTZ Control icon on the quick setting toolbar, to show the PTZ control toolbar. 2. Choose Patrol on the control bar. 3. Double click the patrol or select the patrol and click to call it. Figure 4. 10 PTZ Toolbar- Patrol 4.2.5 Customizing Patterns Purpose: Patterns can be set by recording the movement of the PTZ.
PAGE 56
User Manual of DS-9600/8600/7700/7600 Series NVR 1. Enter the PTZ Control interface. Menu>Camera>PTZ>More Settings 2. Choose pattern number in the option box. Figure 4. 11 PTZ- Pattern 3. Click and use your mouse to drag the image or click the eight directional buttons in the control box under the image to move the PTZ camera. The movement of the PTZ is recorded as the pattern. 4. Click to save the pattern. 4.2.
PAGE 57
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 4. 12 PTZ- Calling Pattern Call pattern in live view mode. Steps: 1. In the live view mode, press PTZ control on the front panel or on the remote control, or click PTZ Control icon on the quick setting toolbar. 2. And then choose Pattern on the control bar. 3. Double click the pattern or select the pattern and click Figure 4. 13 PTZ Toolbar- Pattern 57 to call it.
PAGE 58
User Manual of DS-9600/8600/7700/7600 Series NVR 4.3 PTZ Control Toolbar In the Live View mode, you can press the PTZ Control button on the front panel or on the remote control, or choose the PTZ Control icon to enter the PTZ toolbar. Figure 4. 14 PTZ Toolbar Table 4.
PAGE 59
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 5 Record and Capture Settings 59
PAGE 60
User Manual of DS-9600/8600/7700/7600 Series NVR Note: LTN7600-P series NVR does not support capturing function, and the capturing related operations are not supported with it. 5.1 Configuring Encoding Parameters Purpose: By configuring the encoding parameters you can define the parameters which affect the image quality, such as the transmission stream type, the resolution and so on. Before you start: 1. Make sure that the HDD has already been installed. If not, please install a HDD and initialize it.
PAGE 61
User Manual of DS-9600/8600/7700/7600 Series NVR 2. Encoding Parameters Setting for Recording 1) Select Record tab page to configure. You can configure the stream type, the resolution, and other parameters on your demand. • Pre-record: The time you set to record before the scheduled time or event. For example, when an alarm triggered the recording at 10:00, if you set the pre-record time as 5 seconds, the camera records it at 9:59:55.
PAGE 62
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 5. 5 Capture Encoding 2) 3) 4) Configure the parameters. Click Apply to save the settings. If the parameters can also be used to other channels, click Copy to copy the settings to other channels. Note: The interval is the time period between two capturing actions. You can configure all the parameters on this menu on your demand.
PAGE 63
User Manual of DS-9600/8600/7700/7600 Series NVR 5.2 Configuring Record/Capture Schedule Purpose: Set the record schedule, and then the camera automatically starts/stops recording according to the configured schedule. Note: In this chapter, we take the record schedule procedure as an example, and the same procedure can be applied to configure schedule for both recording and capture. To schedule the automatic capture, you need to choose the Capture tab in the Schedule interface. Steps: 1.
PAGE 64
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 5. 7 Recording Schedule Interface You can click the button to set the accurate time of the schedule. II. To schedule an all-day recording, check the checkbox after the All Day item. Figure 5. 8 Edit Schedule III. To arrange other schedule, leave the All Day checkbox blank and set the Start/End time. Note: Up to 8 periods can be configured for each day. And the time periods can’t be overlapped each other.
PAGE 65
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 5. 10 Draw the Schedule Descriptions of the color icons are shown in the figure below. Figure 5. 11 Descriptions of the color icons Click the Apply button to validate the settings. If the settings can also be used to other channels, click Copy, and then choose the channel to which you want to copy.
PAGE 66
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 5.
PAGE 67
User Manual of DS-9600/8600/7700/7600 Series NVR 5.3 Configuring Motion Detection Record and Capture Purpose: Follow the steps to set the motion detection parameters. In the live view mode, once a motion detection event takes place, the NVR can analyze it and do many actions to handle it. Enabling motion detection function can trigger certain channels to start recording, or trigger full screen monitoring, audio warning, notify the surveillance center and so on.
PAGE 68
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 5. 14 Motion Detection- Mask 4) Click Handling, and the message box for channel information pop up. Figure 5. 15 Motion Detection Handling 3. 5) Select the channels which you want the motion detection event to trigger recording. 6) Click Apply to save the settings. 7) Click OK to back to the upper level menu. 8) Exit the Motion Detection menu. Edit the Motion Detection Record Schedule.
PAGE 69
User Manual of DS-9600/8600/7700/7600 Series NVR 5.4 Configuring Alarm Triggered Record and Capture Purpose: Follow the procedure to configure alarm triggered recording or capture. Steps: 1. Enter the Alarm setting interface. Menu> Configuration> Alarm Figure 5. 16 Alarm Settings 2. Click Alarm Input. Figure 5. 17 Alarm Settings- Alarm Input 1) Select Alarm Input number and configure alarm parameters. 2) Choose N.O (normally open) or N.C (normally closed) for alarm type.
PAGE 70
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 5. 18 Alarm Handling 5) Choose the alarm triggered recording channel. 6) Check the checkbox to select channel. 7) Click Apply to save settings. 8) Click OK to back to the upper level menu. Repeat the above steps to configure other alarm input parameters. If the settings can also be applied to other alarm inputs, click Copy and choose the alarm input number. Figure 5. 19 Copy Alarm Input 3.
PAGE 71
User Manual of DS-9600/8600/7700/7600 Series NVR 5.5 Manual Record and Continuous Capture Purpose: Follow the steps to set parameters for the manual record and continuous capture. Using manual record and continuous capture, you need to manually cancel the record and capture. The manual recording and manual continuous capture is prior to the scheduled recording and capture. Steps: 1. Enter the Manual settings interface. Menu> Manual Or press the REC/SHOT button on the front panel. Figure 5.
PAGE 72
User Manual of DS-9600/8600/7700/7600 Series NVR 5.6 Configuring Holiday Record and Capture Purpose: Follow the steps to configure the record or capture schedule on holiday for that year. You may want to have different plan for recording and capture on holiday. Steps: 1. Enter the Record setting interface. Menu>Record> Holiday Figure 5. 22 Holiday Settings 2. Enable Edit Holiday schedule. 1) Click to enter the Edit interface. Figure 5.
PAGE 73
User Manual of DS-9600/8600/7700/7600 Series NVR 3) 3. Select Mode from the dropdown list. There are three different modes for the date format to configure holiday schedule. 4) Set the start and end date. 5) Click Apply to save settings. 6) Click OK to exit the Edit interface. Enter Record/Capture Schedule settings interface to edit the holiday recording schedule. See Chapter 6.2 Configuring Record/Capture Schedule.
PAGE 74
User Manual of DS-9600/8600/7700/7600 Series NVR 5.7 Configuring Redundant Recording and Capture Purpose: Enabling redundant recording and capture, which means saving the record files and captured pictures not only in the R/W HDD but also in the redundant HDD, will effectively enhance the data safety and reliability. . Steps: 1. Enter HDD Information interface. Menu> HDD Figure 5. 24 HDD General 2. Select the HDD and click to enter the Local HDD Settings interface. 1) Set the HDD property to Redundancy.
PAGE 75
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 5. 26 Encoding Record 2)Select Camera you want to configure in the drop-down list. 3)Check the checkbox of Redundant Record/Capture. 4)Click OK to save settings and back to the upper level menu. Repeat the above steps for configuring other channels.
PAGE 76
User Manual of DS-9600/8600/7700/7600 Series NVR 5.8 Configuring HDD Group for Recording and Capture Purpose: You can group the HDDs and save the record files and captured pictures in certain HDD group. Steps: 1. Enter HDD setting interface. Menu>HDD Figure 5. 27 HDD General 2. Select Advanced on the left bar. Figure 5. 28 Storage Mode Check whether the storage mode of the HDD is Group. If not, set it to Group. For detailed information, please refer to Chapter 12.4 Managing HDD Group. 3.
PAGE 77
User Manual of DS-9600/8600/7700/7600 Series NVR 3) 4) Check the channels you want to save in this group. Click Apply to save settings. Note: After having configured the HDD groups, you can configure the Recording and Capture settings following the procedure provided in Chapter 5.2-5.7.
PAGE 78
User Manual of DS-9600/8600/7700/7600 Series NVR 5.9 Files Protection Purpose: You can lock the recorded files or set the HDD property to Read-only to protect the record files from being overwritten. Protect file by locking the record files: Steps: 1. Enter Playback setting interface. Menu> Playback Figure 5. 30 Playback 2. 3. 4. Select the channels you want to investigate by checking the checkbox to Configure the record type, file type start/end time. Click Search to show the results. . Figure 5.
PAGE 79
User Manual of DS-9600/8600/7700/7600 Series NVR 2) Click to change it to to unlock the file and the file is not protected. Figure 5. 32 Unlocking Attention Protect file by setting HDD property to Read-only Steps: 1. Enter HDD setting interface. Menu> HDD Figure 5. 33 HDD General 2. Click to edit the HDD you want to protect. Figure 5. 34 HDD General- Editing Note: To edit HDD property, you need to set the storage mode of the HDD to Group. See Chapter Managing HDD Group. 3.
PAGE 80
User Manual of DS-9600/8600/7700/7600 Series NVR saved in next R/W HDD. If there is only one HDD, the recording will be stopped.
PAGE 81
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 6 Playback 81
PAGE 82
User Manual of DS-9600/8600/7700/7600 Series NVR 6.1 Playing Back Record Files 6.1.1 Playing Back by Channel Purpose: Play back the recorded video files of a specific channel in the live view mode. Channel switch is supported. Instant playback by channel Steps: Choose a channel in live view mode using the mouse and click the button in the quick setting toolbar. Note: In the instant playback mode, only record files recorded during the last five minutes on this channel will be played back. Figure 6.
PAGE 83
User Manual of DS-9600/8600/7700/7600 Series NVR LTN7732/LTN7616/LTN7732-P8 LTN7604-P4/LTN7608-P4/LTN7608-P8 Figure 6. 2 Right-click Menu under Live View Front Panel: press PLAY button to play back record files of the channel under single-screen live view mode. Under multi-screen live view mode, the recorded files of the top-left channel will be played back. Note: Pressing numerical buttons will switch playback to the corresponding channels during playback process. 2. Playback management.
PAGE 84
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 3 All-day Playback Interface The channel and time selection menu displays by moving the mouse to the right of the playback interface. Click the channel(s) if you want to switch playback to another channel or execute simultaneous playback of multiple channels, as shown in Figure 6. 4 . Figure 6. 4 All-day Playback Interface with Channel List Figure 6. 5 Toolbar of All-day Playback Table 6.
PAGE 85
User Manual of DS-9600/8600/7700/7600 Series NVR / on/Mute clipping Add default tag Add customized tag Tag managemen t Speed down Pause reverse play/ Reverse play/ Single-fram e reverse play Pause play/Play/Si ngle-frame play Stop Speed up Previous day Next day Hide Exit Process bar Video type bar / reverse Note: 1. Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate special frames. 2.
PAGE 86
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 7 Interface of Playback by Time Figure 6. 8 Toolbar of Playback by Time Table 6.
PAGE 87
User Manual of DS-9600/8600/7700/7600 Series NVR 6.1.3 Playing Back by Normal Video Search Purpose: Play back video files searched out by restricting recording type and recording time. The video files in the result list are played back sequentially and channel switch is supported. Recording types contain Normal, Motion, Alarm, Motion / Alarm, Motion & Alarm, Manual and All. Steps: 1. Enter Normal Video Search interface.
PAGE 88
User Manual of DS-9600/8600/7700/7600 Series NVR If more than one channel is optional, clicking button takes you to step 3and step 4. Figure 6. 11 Result of Normal Video Search 4. Choose channels for simultaneous playback. Note: Optional channels for simultaneous playback are the same as the channels chosen to search record files in step 1. And the channel with the recorded file selected in step 2 is the main channel during multi-channel playback and it is displayed at the upper left corner.
PAGE 89
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 13 4-ch Synchronous Playback Interface The hidden list of recorded files displays by moving the mouse to the right of the playback interface. Figure 6. 14 4-ch Synchronous Playback Interface with Video List Figure 6. 15 Toolbar of Normal Playback Table 6.
PAGE 90
User Manual of DS-9600/8600/7700/7600 Series NVR tag / manageme nt down Pause play/Play/Single-fr ame play Stop Speed up Previous file Next file Video search Exit Hide toolbar Progress bar Video type bar Pause reverse play/Reverse play/ Single-frame reverse play / Note: 1. Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate special frames. 2.
PAGE 91
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 17 Video Search by Motion 4. Click button to enter the Playback interface. If there is only one channel is triggered by an alarm input, clicking Full-screen Playback interface of this channel. button takes you to If several channels are triggered, clicking button takes you to step 7and then step 8. Note: Pre-play and post-play can be configured. Figure 6. 18 Result of Video Search by Alarm Input 5.
PAGE 92
User Manual of DS-9600/8600/7700/7600 Series NVR 6. Playback interface. The toolbar in the bottom part of Playback interface can be used to control playing process. Figure 6. 20 Interface of Playback by Event The hidden list of events will be displayed by moving the mouse to the right of the playback interface. Figure 6. 21 Playback Interface with Alarm Input List Figure 6. 22 Toolbar of Playback by Event Table 6.
PAGE 93
User Manual of DS-9600/8600/7700/7600 Series NVR forward / Add default tag Add customized tag Tag manageme nt Speed down Pause reverse play/Reverse play/ Single-frame reverse play Pause play/Play/Single-fr ame play Stop Speed up Previous event Next event Event search Exit Hide Progress bar Video type bar / Note: 1. Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate special frames. 2.
PAGE 94
User Manual of DS-9600/8600/7700/7600 Series NVR Click button to add customized tag and input tag name. Note: Max. 64 tags can be added to a single video file. 2. Tag management. Click button to check, edit and delete tag(s). Figure 6. 24 Tag Management Interface Steps: 1. Enter Tag Search interface. Menu>Playback>Tag Choose channels, tag type and time, and click Search to enter Search Result interface. Note: Two tag types are selectable: All and Tag Keyword. Input keyword if you choose Tag Keyword.
PAGE 95
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 26 Result of Video Search by Tag 3. Playback by tag. Choose a tag and click button to play back the related record file. Figure 6. 27 Interface of Playback by Tag The hidden list of tags will be displayed by moving the mouse to the right of the playback interface.
PAGE 96
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 28 Interface of Playback by Tag with Video List Figure 6. 29 Toolbar of Playback by Tag Table 6.
PAGE 97
User Manual of DS-9600/8600/7700/7600 Series NVR 6.1.6 Playing Back by System Logs Purpose: Play back record file(s) associated with channels after searching system logs. Steps: 1. Enter Log Information interface. Menu>Maintenance>Log Information 2. Click Log Search tab to enter Playback by System Logs. Set search time and type and click Search button. Figure 6. 30 System Log Search Interface 3. Choose a log with record file and click button to enter Playback interface.
PAGE 98
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6.
PAGE 99
User Manual of DS-9600/8600/7700/7600 Series NVR 6.2 Auxiliary Functions of Playback 6.2.1 Playing Back Frame by Frame Purpose: Play video files frame by frame, in case of checking image details of the video when abnormal events happen. Steps: • Using a Mouse: Go to Playback interface. If you choose playback of the record file: click button until the speed changes to Single frame and one click on the playback screen represents playback of one frame.
PAGE 100
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 34 Right-click Menu under Playback The right-click menu: Note: This menu differs slightly from one playback interface to another. Table 6. 6 Detailed Explanation of Right-click Menu under Playback Button Function Return to Search interface Enter Digital Zoom interface Show & hide control interface Return to Playback interface 6.2.3 Adverse Playback of Multi-channel Purpose: You can play back record files of multi-channel adversely.
PAGE 101
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 36 4-ch Synchronous Playback Interface Click to play back the record files adversely.
PAGE 102
User Manual of DS-9600/8600/7700/7600 Series NVR 6.3 Picture Playback Note: The LTN7600-P series does not support this function. Purpose: Search and view captured pictures stored in HDD. Steps: 1. Enter Picture Search interface. Menu>Playback>Picture Set channel, picture type and time and click button to enter Search Result interface. Note: Picture types include Normal, Motion, Alarm, Motion / Alarm, Motion & Alarm, Capture and Continuous Capture. Figure 6. 37 Picture Search 2. View pictures.
PAGE 103
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 6. 39 Picture Playback Interface The hidden list of captured pictures will be displayed by moving the mouse to the right of the playback interface. Figure 6. 40 Playback Interface with Picture List Figure 6. 41 Picture Playback Toolbar Table 6.
PAGE 104
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 7 Backup 104
PAGE 105
User Manual of DS-9600/8600/7700/7600 Series NVR 7.1 Backing up Record Files 7.1.1 Quick Export Purpose: Export record files to backup device(s) quickly. Steps: 1. Enter Video Export interface. Menu>Export>Normal Choose the channel(s) you want to back up and click button. Note: 1) The time duration of record files on a specified channel cannot exceed one day. Otherwise, the message box “Max. 24 hours are allowed for quick export.” will pop up.
PAGE 106
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 3 Export Finished 3. Check backup result. Choose the record file in Export interface and click button to check it. Note: The Player player.exe will be exported automatically during record file export. Figure 7. 4 Checkup of Quick Export Result Using USB1-1 7.1.2 Backing up by Normal Video Search Purpose: The record files can be backup to various devices, such as USB devices (USB flash drives, USB HDDs, USB writer), SATA writer and e-SATA HDD.
PAGE 107
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 5 Normal Video Search for Backup 3. Select record files you want to back up. Click to play the record file if you want to check it. Check the checkbox before the record files you want to back up. Note: The size of the currently selected files is displayed in the lower-left corner of the window. Figure 7. 6 Result of Normal Video Search for Backup 4. Export. Click Export button and start backup.
PAGE 108
User Manual of DS-9600/8600/7700/7600 Series NVR • Click the Refresh button. • Reconnect device. • Check for compatibility from vendor. You can also format USB flash drives or USB HDDs via the device. Figure 7. 7 Export by Normal Video Search using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop-up message box “Export finished”. Figure 7. 8 Export Finished 5. Check backup result. Choose the record file in Export interface and click button to check it.
PAGE 109
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 9 Checkup of Export Result using USB Flash Drive Backup using USB writer and SATA writer Steps: 1. Enter Export interface. Menu>Export>Normal 2. Set search condition and click Search button to enter the search result interface. Figure 7. 10 Normal Video Search for Backup 3. Select record files you want to back up. Click button to play the record file if you want to check it.
PAGE 110
User Manual of DS-9600/8600/7700/7600 Series NVR Check the checkbox before the record files you want to back up. Note: The size of the currently selected files is displayed in the lower-left corner of the window. Figure 7. 11 Result of Normal Video Search for Backup 4. Export. Click Export button and start backup. Note: If the inserted USB writer or SATA writer is not recognized: • Click the Refresh button. • Reconnect device. • Check for compatibility from vendor. Figure 7.
PAGE 111
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 13 Export Finished 5. Check backup result. Choose the record file in Export interface and click button to check it. Note: The Player player.exe will be exported automatically during record file export. Figure 7. 14 Checkup of Export Result using USB Writer Backup using eSATA HDDs Note: The LTN7600-P does not support this function. Steps: 1. Enter Record>Advanced and set the working mode of eSATA HDD at “Export”.
PAGE 112
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 15 Normal Video Search for Backup 3. Select record files you want to back up. Click button to play the record file if you want to check it. Tick record files you want to back up. Note: The size of the currently selected files is displayed in the lower-left corner of the window. Figure 7. 16 Result of Normal Video Search for Backup 4. Export. Click Export button and start backup.
PAGE 113
User Manual of DS-9600/8600/7700/7600 Series NVR HDD is not recognized: • Click the Refresh button. • Reconnect device. • Check for compatibility from vendor. You can also format SATA HDD via the device. Figure 7. 17 Export by Normal Video Search Using eSATA HDD Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”. Figure 7. 18 Export Finished 5. Check backup result. Choose the record file in Export interface and click button to check it.
PAGE 114
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 19 Checkup of Export Result Using eSATA HDD 7.1.3 Backing up by Event Search Purpose: Back up event-related record files using USB devices (USB flash drives, USB HDDs, USB writer), SATA writer or e-SATA HDD. Quick Backup and Normal Backup are supported. Steps: 1. Enter Export interface. Menu>Export>Event 1) Select “Alarm Input” from the dropdown list of Event Type. 2) Select the alarm input No. and time.
PAGE 115
User Manual of DS-9600/8600/7700/7600 Series NVR 2. Select record files to export. 1) Select an alarm input in the list and click Quick Export button to enter Export interface. 2) Clicking Details button will take you to the interface with detailed information of all channels triggered by the selected alarm input. Note: Event types contain Alarm Input and Motion. 3) Clicking Quick Export button will export record files of all channels triggered by the selected alarm input. Figure 7.
PAGE 116
User Manual of DS-9600/8600/7700/7600 Series NVR • Reconnect device. • Check for compatibility from vendor. You can also format USB flash drive or USB HDDs via the device. Figure 7. 23 Export by Event Using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”. Figure 7. 24 Export Finished 4. Check backup result. Note: The Player player.exe will be exported automatically during record file export.
PAGE 117
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 25 Checkup of Event Export Result Using USB Flash Drive 7.1.4 Backing up Video Clips Purpose: You may also select video clips to export directly during Playback, using USB devices (USB flash drives, USB HDDs, USB writer), SATA writer or e-SATA HDD. Steps: 1. Enter Playback interface. Please refer to Chapter 7.1 Playing Back Record Files. 2. During playback, use buttons and in the playback toolbar to start or stop clipping record file(s). 3.
PAGE 118
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 26 Interface of Playback by Time 4. Click Yes to save video clips and enter Export interface, or click No to quit and do not save video clips. Figure 7. 27 Attention to Video Clip Saving 5. Export. Click Export button and start backup. Note: If the inserted USB device is not recognized: • Click the Refresh button. • Reconnect device. • Check for compatibility from vendor. You can also format USB flash drive or USB HDDs via the device. Figure 7.
PAGE 119
User Manual of DS-9600/8600/7700/7600 Series NVR 6. Check backup result. Note: The Player player.exe will be exported automatically during record file export. Figure 7. 30 Checkup of Video Clips Export Result Using USB Flash Drive 7.2 Backing up Pictures Note: LTN7600-P does not support this function. Purpose: Back up pictures using USB devices (USB flash drives, USB HDDs, USB writer), SATA writer or e-SATA HDD. Steps: 1. Enter Export interface.
PAGE 120
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 31 Picture Search for Backup 2. Select pictures you want to back up. Check the checkbox before the pictures you want to back up and click Export button. Note: Here we take USB flash drive as an example. For more backup devices, please refer to chapter Backing up by Normal Video Search. Figure 7. 32 Result of Picture Search 3. Export. Click Export button and start backup.
PAGE 121
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 7. 33 Export Pictures Using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop-up message “Export finished”. Figure 7. 34 Export Finished 4. Check backup result. Figure 7.
PAGE 122
User Manual of DS-9600/8600/7700/7600 Series NVR 7.3 Managing Backup Devices Management of USB flash drives, USB HDDs and eSATA HDDs. 1. Enter Search Result interface of record files. Menu>Export>Normal Set search condition and click Search button to enter Search Result interface. Note: At least one channel shall be selected. Figure 7. 36 Normal Video Search for Backup 2. Select record files you want to back up. Click Export button to enter Export interface.
PAGE 123
User Manual of DS-9600/8600/7700/7600 Series NVR delete it. Select a record file in the backup device and click Click Format button to format the backup device. Note: If the inserted USB device is not recognized: button to play it. • Click the Refresh button. • Reconnect device. • Check for compatibility from vendor. Figure 7. 38 USB Flash Drive Management Management of USB writers and DVD-R/W 1. Enter Search Result interface of record files.
PAGE 124
User Manual of DS-9600/8600/7700/7600 Series NVR Note: At least one record file shall be selected. Figure 7. 40 Result of Normal Video Search for Backup 3. Backup device management. Click Erase button if you want to erase the files from a re-writable CD/DVD. Note: There must be a re-writable CD/DVD when you make this operation. Note: If the inserted USB writer or DVD-R/W is not recognized: • Click the Refresh button. • Reconnect device. • Check for compatibility from vendor. Figure 7.
PAGE 125
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 8 Alarm Settings 125
PAGE 126
User Manual of DS-9600/8600/7700/7600 Series NVR 8.1 Setting Motion Detection Alarm Steps: 1. Enter Motion Detection interface of Camera Management and choose a camera you want to set up motion detection. Menu> Camera> Motion Figure 8. 1 Motion Detection Setup Interface 2. Set up detection area and sensitivity. Tick “Enable Motion Detection”, use the mouse to draw detection area(s) and drag the sensitivity bar to set sensitivity. Click Handling button and set alarm response actions. 3.
PAGE 127
User Manual of DS-9600/8600/7700/7600 Series NVR 4. Set up arming schedule of the channel. Select Arming Schedule tab to set the channel’s arming schedule for the motion detection. Choose one day of a week and up to eight time periods can be set within each day. Note: Time periods shall not be repeated or overlapped. Figure 8. 3 Set Arming Schedule of Motion Detection 5. Click Handling tab to set up alarm response actions of motion alarm (please refer to Chapter Setting Alarm Response Actions).
PAGE 128
User Manual of DS-9600/8600/7700/7600 Series NVR 8.2 Setting Sensor Alarms Purpose: Set handling method of an external sensor alarm. Steps: 1. Enter Alarm Settings of System Configuration and select an alarm input. Menu> Configuration> Alarm Select Alarm Input tab to enter Alarm Input Settings interface. Figure 8. 4 Alarm Status Interface of System Configuration 2. Set up the handling method of the selected alarm input.
PAGE 129
User Manual of DS-9600/8600/7700/7600 Series NVR Choose one day of a week and Max. eight time periods can be set within each day. Note: Time periods shall not be repeated or overlapped. 5. Select Handling tab to set up alarm response actions of the alarm input (please refer to Chapter Setting Alarm Response Actions). Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days. Figure 8.
PAGE 130
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 8.
PAGE 131
User Manual of DS-9600/8600/7700/7600 Series NVR 8.3 Detecting Video Loss Alarm Purpose: Detect video loss of a channel and take alarm response action(s). Steps: 1. Enter Video Loss interface of Camera Management and select a channel you want to detect. Menu> Camera> Video Loss Figure 8. 9 Video Loss Setup Interface 2. Set up handling method of video loss. Check the checkbox of “Enable Video Loss Alarm”, and click Handling button to set up handling method of video loss. Figure 8.
PAGE 132
User Manual of DS-9600/8600/7700/7600 Series NVR Note: Time periods shall not be repeated or overlapped. Figure 8. 11 Set Arming Schedule of Video Loss 4. Select Handling tab to set up alarm response action of video loss (please refer to Chapter Setting Alarm Response Actions). Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days. 5. Click the OK button to complete the video loss settings of the channel.
PAGE 133
User Manual of DS-9600/8600/7700/7600 Series NVR 8.4 Detecting Video Tampering Alarm Purpose: Trigger alarm when the lens is covered and take alarm response action(s). Steps: 1. Enter Video Tampering interface of Camera Management and select a channel you want to detect video tampering. Menu> Camera> Tamper-proof Figure 8. 12 Tamper-proof Setup Interface 2. Set the video tampering handling method of the channel. Check the checkbox of “Enable Tamper-proof”.
PAGE 134
User Manual of DS-9600/8600/7700/7600 Series NVR 3. Set arming schedule and alarm response actions of the channel. 1) Click Arming Schedule tab to set the channel’s arming schedule. 2) Choose one day of a week and Max. eight time periods can be set within each day. Note: Time periods shall not be repeated or overlapped. Figure 8. 14 Set Arming Schedule of Video Tampering 4.
PAGE 135
User Manual of DS-9600/8600/7700/7600 Series NVR 8.5 Handling Exceptions Alarm Purpose: Exception settings refer to the handling method of various exceptions, e.g. • HDD Full: The HDD is full. • HDD Error: Writing HDD error or unformatted HDD. • Network Disconnected: Disconnected network cable. • IP Conflicted: Duplicated IP address. • Illegal Login: Incorrect user ID or password. • Abnormal Record/Capture: No space for saving recorded files or captured images.
PAGE 136
User Manual of DS-9600/8600/7700/7600 Series NVR 8.6 Setting Alarm Response Actions Purpose: Alarm response actions will be activated when an alarm or exception occurs, including Full Screen Monitoring, Audible Warning (buzzer), Notify Surveillance Center, Upload Picture to FTP, Trigger Alarm Output and Send Email.
PAGE 137
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 8. 16 Alarm Output Setup Interface 2. Set up arming schedule of the alarm output. Choose one day of a week and up to 8 time periods can be set within each day. Note: Time periods shall not be repeated or overlapped. Figure 8. 17 Set Arming Schedule of Alarm Output 3. Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days.
PAGE 138
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 8.
PAGE 139
User Manual of DS-9600/8600/7700/7600 Series NVR 8.7 Triggering or Clearing Alarm Output Manually Purpose: Sensor alarm can be triggered or cleared manually. If “Manually Clear” is selected in the dropdown list of dwell time of an alarm output, the alarm can be cleared only by clicking Clear button in the following interface. Steps: Select the alarm output you want to trigger or clear and make related operations.
PAGE 140
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 9 Network Settings 140
PAGE 141
User Manual of DS-9600/8600/7700/7600 Series NVR 9.1 Configuring General Settings Purpose: Network settings must be properly configured before you operate NVR over network. Steps: 1. Enter the Network Settings interface. Menu >Configuration>Network 2. Select the General tab. LTN7616/LTN7732 LTN7732-P8/LTN7604-P4/LTN7608-P4/LTN7608-P8 Figure 9. 1 Network Settings Interface 3.
PAGE 142
User Manual of DS-9600/8600/7700/7600 Series NVR 9.2 Configuring Advanced Settings 9.2.1 Configuring PPPoE Settings Purpose: Your NVR also allows access by Point-to-Point Protocol over Ethernet (PPPoE). Steps: 1. Enter the Network Settings interface. Menu >Configuration> Network 2. Select the PPPoE tab to enter the PPPoE Settings interface, as shown in Figure 9. 2. Figure 9. 2 PPPoE Settings Interface 3. 4. Check the PPPoE checkbox to enable this feature.
PAGE 143
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 9. 3 DDNS Settings Interface 3. 4. Check the DDNS checkbox to enable this feature. Select DDNS Type. Five different DDNS types are selectable: IPServer, DynDNS, PeanutHull, NO-IP and HIDDNS. • IPServer: Enter Server Address for IPServer. Figure 9. 4 IPServer Settings Interface • DynDNS: 1) Enter Server Address for DynDNS (i.e. members.dyndns.org). 2) In the NVR Domain Name text field, enter the domain obtained from the DynDNS website.
PAGE 144
User Manual of DS-9600/8600/7700/7600 Series NVR • NO-IP: Enter the account information in the corresponding fields. Refer to the DynDNS settings. 1) Enter Server Address for NO-IP. 2) In the NVR Domain Name text field, enter the domain obtained from the NO-IP website (www.no-ip.com). 3) Enter the User Name and Password registered in the NO-IP website. Figure 9. 7 NO-IP Settings Interface • HIDDNS: Enter the Server Address and Device Domain Name for HIDDNS.
PAGE 145
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 9. 9 Register an Account 3) In the Device Management interface, click to register the device. Figure 9. 10 Register the Device 5. Note: The device name can only contain the lower-case English letter, numeric and ‘-’; and it must start with the lower-case English letter and cannot end with ‘-’. Click to save and exit the interface. 9.2.
PAGE 146
User Manual of DS-9600/8600/7700/7600 Series NVR 5. • Interval: Time interval between the two synchronizing actions with NTP server. The unit is minute. • NTP Server: IP address of NTP server. • NTP Port: Port of NTP server. Click to save and exit the interface. Note: The time synchronization interval can be set from1 to 10080min, and the default value is 60min.
PAGE 147
User Manual of DS-9600/8600/7700/7600 Series NVR Menu >Configuration> Network 2. Select the More Settings tab to enter the More Settings interface, as shown in Figure 9. 13. Figure 9. 13 More Settings Interface 3. Enter Alarm Host IP and Alarm Host Port in the text fields. The Alarm Host IP refers to the IP address of the remote PC on which the Network Video Surveillance Software (e.g.
PAGE 148
User Manual of DS-9600/8600/7700/7600 Series NVR Note: The multicast function should be supported by the network switch to which the NVR is connected. 9.2.7 Configuring RTSP Purpose: The RTSP (Real Time Streaming Protocol) is a network control protocol designed for use in entertainment and communications systems to control streaming media servers. Steps: 1. Enter the Network Settings menu Menu >Configuration> Network 2. Select the More Settings tab to enter the More Settings menu, as shown in Figure 9.
PAGE 149
User Manual of DS-9600/8600/7700/7600 Series NVR 4. Enter the Server Port and HTTP Port in the text fields. The default Server Port is 8000 and the HTTP Port is 80, and you can change them according to different requirements. 5. Click to save and exit the interface. Note: The Server Port should be set to the range of 2000-65535 and it is used for remote client software access. The HTTP port is used for remote IE access. 9.2.
PAGE 150
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 9. 19 Email Settings Interface 7. 8. 9. Configure the following Email settings: Enable Server Authentication (optional): Check the checkbox to enable the server authentication feature. User Name: The user account of sender’s Email for SMTP server authentication. Password: The password of sender’s Email for SMTP server authentication. SMTP Server: The SMTP Server IP address or host name (e.g., smtp.263xmail.com). SMTP Port No.: The SMTP port.
PAGE 151
User Manual of DS-9600/8600/7700/7600 Series NVR Before you start: If you want to enable the UPnP™ function of the device, you must enable the UPnP™ function of the router to which your device is connected. When the network working mode of the device is set as multi-address, the Default Route of the device should be in the same network segment as that of the LAN IP address of the router. Steps: 1. Enter the Network Settings interface. Menu > Configuration > Network 2.
PAGE 152
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 9. 23 UPnP™ Settings Finished 6. Click to save the settings.
PAGE 153
User Manual of DS-9600/8600/7700/7600 Series NVR 9.3 Checking Network Traffic Purpose: You can check the network traffic to obtain real-time information of NVR such as linking status, MTU, sending/receiving rate, etc. Steps: 1. Enter the Network Traffic interface. Menu >Maintenance>Net Detect Figure 9. 24 Network Traffic Interface 2. You can view the sending rate and receiving rate information on the interface. The traffic data is refreshed every 1 second.
PAGE 154
User Manual of DS-9600/8600/7700/7600 Series NVR 9.4 Configuring Network Detection Purpose: You can obtain network connecting status of NVR through the network detection function, including network delay, packet loss, etc. 9.4.1 Testing Network Delay and Packet Loss Steps: 1. Enter the Network Traffic interface. Menu >Maintenance>Net Detect 2. Click the Network Detection tab to enter the Network Detection menu, as shown in Figure 9. 25. Figure 9. 25 Network Detection Interface 3. 4.
PAGE 155
User Manual of DS-9600/8600/7700/7600 Series NVR 3. Select the backup device from the dropdown list of Device Name, as shown in Figure 9. 27. Note: Click if the connected local backup device cannot be displayed. When it fails to detect the backup device, please check whether it is compatible with the NVR. You can format the backup device if the format is incorrect. Figure 9. 27 Export Network Packet 4. Click to start exporting. 5.
PAGE 156
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 9. 29 Network status checking If the network is normal the following message box pops out. Figure 9. 30 Network status checking result If the message box pops out with other information instead of this one, you can click to show the quick setting interface of the network parameters.
PAGE 157
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 9. 31 Network parameters configuration 9.4.4 Checking Network Statistics Purpose: You can check the network status to obtain the real-time information of NVR. Steps: 1. Enter the Network Detection interface. Menu>Maintenance>Net Detection 2. Choose the Network Stat. tab. Figure 9. 32 Network Stat. Interface 3.
PAGE 158
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 10 HDD Management 158
PAGE 159
User Manual of DS-9600/8600/7700/7600 Series NVR 10.1 Initializing HDDs Purpose: A newly installed hard disk drive (HDD) must be initialized before it can be used with your NVR. Steps: 1. Enter the HDD Information interface. Menu > HDD> General Figure 10. 1 HDD Information Interface 2. Select HDD to be initialized. 3. Click the Init button. Figure 10. 2 Confirm Initialization 4. Select the OK button to start initialization. Figure 10. 3 Status changes to Formatting 5.
PAGE 160
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 10. 4 HDD Status Changes to Normal Note: Initializing the HDD will erase all data on it.
PAGE 161
User Manual of DS-9600/8600/7700/7600 Series NVR 10.2 Managing Network HDD Purpose: You can add the allocated NAS or disk of IP SAN to NVR, and use it as network HDD. Steps: 1. Enter the HDD Information interface. Menu > HDD>General. Figure 10. 5 HDD Information Interface 2. Click the Add button to enter the Add NetHDD interface, as shown in Figure 10. 6. Figure 10. 6 HDD Information Interface 3. 4. 5. Add the allocated NetHDD. Select the type to NAS or IP SAN. Configure the NAS or IP SAN settings.
PAGE 162
User Manual of DS-9600/8600/7700/7600 Series NVR 1) Enter the NetHDD IP address in the text field. 2) Enter the NetHDD Directory in the text field. 3) Click the OK button to add the configured NAS disk. Note: Up to 8 NAS disks can be added. Figure 10. 7 Add NAS Disk • Add IP SAN: 1) Enter the NetHDD IP address in the text field. 2) Click the Search button to the available IP SAN disks. 3) Select the IP SAN disk from the list shown below. 4) Click the OK button to add the selected IP SAN disk.
PAGE 163
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 10.
PAGE 164
User Manual of DS-9600/8600/7700/7600 Series NVR 10.3 Managing eSATA Note: This function is not supported with LTN7600-P series NVR. Purpose: When there is an external eSATA device connected to NVR, you can configure eSATA for the use of Record/Capture or Export, and you can manage the eSATA in the NVR. Steps: 1. Enter the Advanced Record Settings interface. Menu >Record>Advanced 2. Select the eSATA type to Export or Record/Capture from the dropdown list of eSATA. Export: use the eSATA for backup.
PAGE 165
User Manual of DS-9600/8600/7700/7600 Series NVR 10.4 Managing HDD Group 10.4.1 Setting HDD Groups Purpose: Multiple HDDs can be managed in groups. Video from specified channels can be recorded onto a particular HDD group through HDD settings. Steps: 1. Enter the Storage Mode interface. Menu > HDD > Advanced 2. Set the Mode to Group, as shown in Figure 10. 12. Figure 10. 12 Storage Mode Interface 3. Click the Apply button and the following Attention box will pop up. Figure 10.
PAGE 166
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 10. 14 Local HDD Settings Interface 7. Select the Group number for the current HDD. Note: The default group No. for each HDD is 1. 8. Click the OK button to confirm the settings. Figure 10. 15 Confirm HDD Group Settings 9. In the pop-up Attention box, click the Yes button to finish the settings. 10.4.2 Setting HDD Property Purpose: The HDD property can be set to redundancy, read-only or read/write (R/W).
PAGE 167
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 10. 16 Set HDD Property 3. Set the HDD property to R/W, Read-only or Redundancy. 4. Click the OK button to save the settings and exit the interface. 5. In the HDD Information menu, the HDD property will be displayed in the list. Note: At least 2 hard disks must be installed on your NVR when you want to set a HDD to Redundancy, and there is one HDD with R/W property.
PAGE 168
User Manual of DS-9600/8600/7700/7600 Series NVR 10.5 Configuring Quota Mode Purpose: Each camera can be configured with allocated quota for the storage of recorded files or captured pictures. Steps: 1. Enter the Storage Mode interface. Menu > HDD > Advanced 2. Set the Mode to Quota, as shown in Figure 10. 17. Note: The NVR must be rebooted to enable the changes to take effect. Figure 10. 17 Storage Mode Settings Interface 3. Select a camera for which you want to configure quota. 4.
PAGE 169
User Manual of DS-9600/8600/7700/7600 Series NVR 5. You can copy the quota settings of the current camera to other cameras if required. Click the Copy button to enter the Copy Camera menu, as shown in Figure 10. 19. Figure 10. 19 Copy Settings to Other Camera(s) 6. Select the camera (s) to be configured with the same quota settings. You can also click the checkbox of IP Camera to select all cameras. 7. Click the OK button to finish the Copy settings and back to the Storage Mode interface. 8.
PAGE 170
User Manual of DS-9600/8600/7700/7600 Series NVR 10.6 Checking HDD Status Purpose: You may check the status of the installed HDDs on NVR so as to take immediate check and maintenance in case of HDD failure. Checking HDD Status in HDD Information Interface Steps: 1. Enter the HDD Information interface. Menu > HDD>General 2. Check the status of each HDD which is displayed on the list, as shown in Figure 10. 20. Figure 10.
PAGE 171
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 10.
PAGE 172
User Manual of DS-9600/8600/7700/7600 Series NVR 10.7 HDD Detection Purpose: The device provides the HDD detection function such as the adopting of the S.M.A.R.T. and the Bad Sector Detection technique. The S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitoring system for HDD to detect and report on various indicators of reliability in the hopes of anticipating failures. S.M.A.R.T. Settings Steps: 1. Enter the S.M.A.R.T Settings interface. Menu > HDD >S.M.A.R.T. 2.
PAGE 173
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 10. 23 Bad Sector Detection 4. If the HDD is normal you can see the green color icon on the screen, otherwise the red icon is shown. And you can click Error info button to see the detailed damage information And you can also pause or cancel the detection.
PAGE 174
User Manual of DS-9600/8600/7700/7600 Series NVR 10.8 Configuring HDD Error Alarms Purpose: You can configure the HDD error alarms when the HDD status is Uninitialized or Abnormal. Steps: 1. Enter the Exception interface. Menu > Configuration > Exceptions 2. Select the Exception Type to HDD Error from the dropdown list. 3. Click the checkbox(s) below to select the HDD error alarm type (s), as shown in Figure 10. 24.
PAGE 175
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 11 Camera Settings 175
PAGE 176
User Manual of DS-9600/8600/7700/7600 Series NVR 11.1 Configuring OSD Settings Purpose: You can configure the OSD (On-screen Display) settings for the camera, including date /time, camera name, etc. Steps: 1. Enter the OSD Configuration interface. Menu > Camera > OSD 2. Select the camera to configure OSD settings. 3. Edit the Camera Name in the text field. 4. Configure the Display Name, Display Date and Display Week by clicking the checkbox. 5. Select the Date Format, Time Format and Display Mode.
PAGE 177
User Manual of DS-9600/8600/7700/7600 Series NVR 11.2 Configuring Privacy Mask Purpose: You are allowed to configure the four-sided privacy mask zones that cannot be viewed by the operator. The privacy mask can prevent certain surveillance areas to be viewed or recorded. Steps: 1. Enter the Privacy Mask Settings interface. Menu > Camera >Privacy Mask 2. Select the camera to set privacy mask. 3. Click the checkbox of Enable Privacy Mask to enable this feature. Figure 11.
PAGE 178
User Manual of DS-9600/8600/7700/7600 Series NVR 11.3 Configuring Video Parameters Steps: 1. Enter the Image Settings interface. Menu > Camera >Image Figure 11. 4 Image Settings Interface 2. Select the camera to set image parameters. 3. You can click on the arrow to change the value of each parameter. 4. Click the Apply button to save the settings.
PAGE 179
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 12 NVR Management Maintenance 179 and
PAGE 180
User Manual of DS-9600/8600/7700/7600 Series NVR 12.1 Viewing System Information 12.1.1 Viewing Device Information Steps: 1. Enter the System Information interface. Menu >Maintenance>System Info 2. Click the Device Info tab to enter the Device Information menu to view the device name, model, serial No. , firmware version and encode version, as shown in Figure 12. 1. Figure 12. 1 Device Information Interface 12.1.2 Viewing Camera Information Steps: 1. Enter the System Information interface.
PAGE 181
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 12. 2 Camera Information Interface 12.1.3 Viewing Record Information Steps: 1. Enter the System Information interface. Menu >Maintenance>System Info 2. Click the Record tab to enter the Record Information menu to view the recording status encoding parameters of each camera, as shown in Figure 12. 3. Figure 12.
PAGE 182
User Manual of DS-9600/8600/7700/7600 Series NVR 12.1.4 Viewing Alarm Information Steps: 1. Enter the System Information interface. Menu >Maintenance>System Info 2. Click the Alarm tab to enter the Alarm Information menu to view the alarm information, as shown in Figure 12. 4. Figure 12. 4 Alarm Information Interface 12.1.5 Viewing Network Information Steps: 1. Enter the System Information interface. Menu >Maintenance>System Info 2.
PAGE 183
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 12. 5 Network Information Interface 12.1.6 Viewing HDD Information Steps: 1. Enter the System Information interface. Menu >Maintenance>System Info 2. Click the HDD tab to enter the HDD Information menu to view the HDD status, free space, property, etc., as shown in Figure 12. 6. Figure 12.
PAGE 184
User Manual of DS-9600/8600/7700/7600 Series NVR 12.2 Searching & Export Log Files Purpose: The operation, alarm, exception and information of the NVR can be stored in log files, which can be viewed and exported at any time. Steps: 1. Enter the Log Search interface. Menu >Maintenance>Log Search Figure 12. 7 Log Search Interface 2. Set the log search conditions to refine your search, including the Start Time, End Time, Major Type and Minor Type. 3. Click the Search button to start search log files. 4.
PAGE 185
User Manual of DS-9600/8600/7700/7600 Series NVR 5. You can click the button of each log or double click it to view its detailed information, as shown in Figure 12. 9. And you can also click the if available. button to view the related video files Figure 12. 9 Log Details 6. If you want to export the log files, click the Export button to enter the Export menu, as shown in Figure 12. 10. Figure 12. 10 Export Log Files 7. Select the backup device from the dropdown list of Device Name. 8.
PAGE 186
User Manual of DS-9600/8600/7700/7600 Series NVR To export all the log files: You can enter the Log Export interface. Menu> Maintenance> Log Information> Log Export Figure 12. 11 Log Export Interface You can check the checkbox of the HDD. Click the Export button to export all the log files stored in the HDD.
PAGE 187
User Manual of DS-9600/8600/7700/7600 Series NVR 12.3 Importing/Exporting Configuration Files Purpose: The configuration files of the NVR can be exported to local device for backup; and the configuration files of one NVR can be imported to multiple NVR devices if they are to be configured with the same parameters. Steps: 1. Enter the Import/Export Configuration File interface. Menu > Maintenance >Import/Export Figure 12. 12 Import/Export Config File 2.
PAGE 188
User Manual of DS-9600/8600/7700/7600 Series NVR 12.4 Upgrading System Purpose: The firmware on your NVR can be upgraded by local backup device or remote FTP server. 12.4.1 Upgrading by Local Backup Device Steps: 1. Connect your NVR with a local backup device where the update firmware file is located. 2. Enter the Upgrade interface. Menu >Maintenance>Upgrade 3. Click the Local Upgrade tab to enter the local upgrade menu, as shown in Figure 12. 13. Figure 12. 13 Local Upgrade Interface 4.
PAGE 189
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 12. 14 FTP Upgrade Interface 3. Enter the FTP Server Address in the text field. 4. Click the Upgrade button to start upgrading. 5. After the upgrading is complete, reboot the NVR to activate the new firmware.
PAGE 190
User Manual of DS-9600/8600/7700/7600 Series NVR 12.5 Restoring Default Settings Steps: 1. Enter the Default interface. Menu > Maintenance > Default Figure 12. 15 Restore Factory Default 2. Click the OK button to restore the default settings. Note: Except the network parameters (including IP address, subnet mask, gateway, MTU, NIC working mode, default route and server port), all other parameters of the device will be restored to factory default settings.
PAGE 191
User Manual of DS-9600/8600/7700/7600 Series NVR Chapter 13 Others 191
PAGE 192
User Manual of DS-9600/8600/7700/7600 Series NVR 13.1 Configuring RS-232 Serial Port Note: This function is not supported with LTN7600-P NVR. Purpose: The RS-232 port can be used in two ways: • Parameters Configuration: Connect a PC to the NVR through the PC serial port. Device parameters can be configured by using software such as HyperTerminal. The serial port parameters must be the same as the NVR’s when connecting with the PC serial port.
PAGE 193
User Manual of DS-9600/8600/7700/7600 Series NVR 13.2 Configuring General Settings Purpose: You can configure the BNC output standard, VGA output resolution, mouse pointer speed through the Menu > Configuration > General interface. Steps: 1. Enter the General Settings interface. Menu >Configuration> General 2. Select the General tab. Figure 13. 2 General Settings Interface 3. 4. Configure the following settings: • Language: The default language used is English.
PAGE 194
User Manual of DS-9600/8600/7700/7600 Series NVR 13.3 Configuring DST Settings Steps: 1. Enter the General Settings interface. Menu >Configuration>General 2. Choose DST Settings tab. Figure 13. 3 DST Settings Interface You can check the checkbox before the Auto DST Adjustment item. Or you can manually check the Enable DST checkbox, and then you choose the date of the DST period.
PAGE 195
User Manual of DS-9600/8600/7700/7600 Series NVR 13.4 Configuring More Settings for Device Parameters Steps: 1. Enter the General Settings interface. Menu >Configuration>General 2. Click the More Settings tab to enter the More Settings interface, as shown in Figure 13. 4. Figure 13. 4 More Settings Interface 3. Configure the following settings: 4. • Device Name: Edit the name of NVR. • Device No.: Edit the serial number of NVR. The Device No. can be set in the range of 1~255, and the default No.
PAGE 196
User Manual of DS-9600/8600/7700/7600 Series NVR 13.5 Managing User Accounts Purpose: There is a default account in the NVR: Administrator. The Administrator user name is admin and the password is 12345. The Administrator has the permission to add and delete user and configure user parameters. 13.5.1 Adding a User Steps: 1. Enter the User Management interface. Menu >Configuration>User Figure 13. 5 User Management Interface 2. Click the Add button to enter the Add User interface.
PAGE 197
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 13. 6 Add User Menu 3. Enter the information for new user, including User Name, Password, Level and User’s MAC Address. Level: Set the user level to Operator or Guest. Different user levels have different operating permission. • Operator: The Operator user level has permission of Two-way Audio in Remote Configuration and all operating permission in Camera Configuration. • 4.
PAGE 198
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 13. 8 User Permission Settings Interface 6. Set the operating permission of Local Configuration, Remote Configuration and Camera Configuration for the user. Local Configuration • Local Log Search: Searching and viewing logs and system information of NVR. • Local Parameters Settings: Configuring parameters, restoring factory default parameters and importing/exporting configuration files.
PAGE 199
User Manual of DS-9600/8600/7700/7600 Series NVR • • • • Local Playback: Locally playing back recorded files of the selected camera (s). Remote Playback: Remotely playing back recorded files of the selected camera (s). Local PTZ Control: Locally controlling PTZ movement of the selected camera (s). Remote PTZ Control: Remotely controlling PTZ movement of the selected camera (s). • Local Video Export: Locally exporting recorded files of the selected camera (s). 7.
PAGE 200
User Manual of DS-9600/8600/7700/7600 Series NVR Figure 13. 10 Edit User Interface 4. 5. Edit the user information, including user name, password, level and MAC address. Click the OK button to save the settings and exit the menu.
PAGE 201
User Manual of DS-9600/8600/7700/7600 Series NVR Appendix 201
PAGE 202
User Manual of DS-9600/8600/7700/7600 Series NVR Glossary • Dual Stream: Dual stream is a technology used to record high resolution video locally while transmitting a lower resolution stream over the network. The two streams are generated by the DVR, with the main stream having a maximum resolution of 4CIF and the sub-stream having a maximum resolution of CIF. • HDD: Acronym for Hard Disk Drive. A storage medium which stores digitally encoded data on platters with magnetic surfaces.
PAGE 203
User Manual of DS-9600/8600/7700/7600 Series NVR FAQ • Why does my NVR make a beeping sound after booting? The possible reasons for the warning beep on the NVR are as follows: a) There is no HDD installed in the NVR. b) The HDD is not initialized. c) HDD error To cancel the beeping sound and use the NVR without HDD, enter the Exception Settings interface. For detailed information, see Chapter Handling Exceptions Alarm.
PAGE 204
User Manual of DS-9600/8600/7700/7600 Series NVR List of Compatible IP Cameras List of IP Cameras Supported by LTN7700/7600 Series NVR Note: ONVIF compatibility refers to the camera can be supported both when it uses the ONVIF protocol and its private protocols. Only ONVIF is supported refers to the camera can only be supported when it uses the ONVIF protocol. IPC Manufacturer or Max.
PAGE 205
User Manual of DS-9600/8600/7700/7600 Series NVR CMIP5323 V4.0.1 build 120508 1600×1200 √ √ CMIP5323-Z V4.0.1 build 120508 1600×1200 √ √ CMIP3923 V4.0.1 build 120508 1600×1200 √ √ CMIP3923-Z V4.0.1 build 120508 1600×1200 √ √ CMIP3122 V4.0.1 build 120508 1600×1200 √ √ CMIP8822-W V4.0.1 build 120508 1600×1200 √ √ 1280×960 √ √ 1280×960 √ √ WV-SF336H Application:1.06 Image data:1.06 Panasonic WV-SP306H Application:1.34 Image data:1.06 D5118 1.8.2-20120327-2.9310-A1.