4-inch Speed Dome Installation Manual V1.0.
1 Installation Manual of 4-inch Speed Dome Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact the dealer. This manual is applicable to 4-inch Speed Domes. This manual may contain several technically inaccurate points or printing errors, and the content is subject to change without notice. The updates will be added into the new version of this manual. We will readily improve or update the products or procedures described in the manual.
2 Installation Manual of 4-inch Speed Dome Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
3 Installation Manual of 4-inch Speed Dome Safety Warnings and Cautions Please pay attention to the following warnings and cautions: Hazardous Voltage may be present: Special measures and precautions must be taken when using this device. Some potentials (voltages) on the device may present a hazard to the user. This device should only be used by employees from our company with knowledge and training in working with these types of devices that contain live circuits.
4 Installation Manual of 4-inch Speed Dome Power Cord Requirements: The connector that plugs into the wall outlet must be a grounding-type male plug designed for use in your region. It must have certification marks showing certification by an agency in your region. The connector that plugs into the AC receptacle on the power supply must be an IEC 320, sheet C13, female connector. See the following website for more information http://kropla.com/electric2.htm.
5 Installation Manual of 4-inch Speed Dome Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Warnings: Cautions: Follow these safeguards to prevent Follow these precautions to serious injury or death.
6 Installation Manual of 4-inch Speed Dome Please use the provided glove when open up the dome cover, avoid direct contact with the dome cover, because the acidic sweat of the fingers may erode the surface coating of the dome cover. Please use a soft and dry cloth when clean inside and outside surfaces of the dome cover, do not use alkaline detergents.
7 Installation Manual of 4-inch Speed Dome Preparation for Installation Basic requirements. All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Check whether all the accessories are included according to the packing list, make sure that the installation place and mode conform to the demands. If not, please contact the supplier.
8 Installation Manual of 4-inch Speed Dome Table of Contents Chapter 1 1.1 Installation............................................................................................................................................ 1 Installation and Cabling ........................................................................................................................................ 1 1.1.1 Installing the Speed Dome ..................................................................................
1 Installation Manual of 4-inch Speed Dome Chapter 1 Installation Before you start: Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. 1.1 Installation and Cabling 1.1.1 Installing the Speed Dome There are several ways to install the analog speed dome or network speed dome. The ceiling mounting is taken as an example below. Please refer to the Chapter 2 and Chapter 3 for other installation ways. Steps: 1.
2 Installation Manual of 4-inch Speed Dome Camera Module Three Screws Back Box Figure 1-2 Remove the Back Box Dome Liner Figure 1-3 Camera Module 5. Secure the ceiling mount to the ceiling. 1) Stick the drill template on the place where you want to install the speed dome. 2) Drill three φ6 screw holes with the drill template as shown in Figure 1-4.
3 Installation Manual of 4-inch Speed Dome Drill Template Φ6 Screw Hole Figure 1-4 Drill Template 6. Secure the back box to the ceiling with screws as shown in Figure 1-5. Figure 1-5 Install the Ceiling Mount Notes: For cement ceiling mounting, you need to use the expansion screw to fix the mount. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the mount. For wooden ceiling mounting, you can just use the self-tapping screw to fix the bracket.
4 Installation Manual of 4-inch Speed Dome 7. Set the address, baudrate, etc. for the speed dome. There is a DIP switch on the camera module as shown in Figure 1-6. You can set the parameters like address, baudrate, etc. with the DIP switch. Please refer to the section 1.3 DIP Switch Settings for detailed information. DIP Switch 1 2 3 4 5 6 7 8 9 10 Figure 1-6 DIP Switch 8. For the network speed dome, there is a SD card slot on the camera module as shown in Figure 1-7.
5 Installation Manual of 4-inch Speed Dome 9. Install the camera module to the back box. 10. Secure the two parts with three screws as shown in Figure 1-8. Three Screws Figure 1-8 Install the Camera Module 11. Align the screws of the lower dome with the camera module. 12. Secure the lower dome with three screws as shown in Figure 1-9.
6 Installation Manual of 4-inch Speed Dome 13. Tear off the plastic film from the lower dome. Figure 1-10 Tear off the Film 1.1.2 Connecting the Cables Before you start: Please make sure to cut off the power of the dome before connect the cables. The cable interfaces of analog speed dome and network speed dome are shown in Figure 1-11 and Figure 1-12 respectively. The cables of RS-485, alarm in/out, etc. are distinguished by different colors.
7 Installation Manual of 4-inch Speed Dome Label Description Labels RED BROWN BLACK YELLOW ORANGE AC24V AC24V R485 R485 + VIDEO Orange GND Yellow ALARM_IN2 Green ALARM_IN1 Blue ALARM_OUT1A White ALARM_OUT1B Video Output OEDIV Figure 1-11 Cables of Analog Speed Dome Label 1 Description YELLOW ORANGE Label 1 R485 R485 + Black AUDIO_IN Brown GND Red AUDIO_OUT Orange ALARM_IN1 Yellow GND Green ALARM_IN2 Blue ALARM_OUT1A Purple ALARM_OUT1B Label 2 Label 2 Description RED AC24V BROWN BLACK AC24V Fi
8 Installation Manual of 4-inch Speed Dome are used to set the baudrate. The eighth and ninth switches are used to set the parity and Manchester Code protocol. The tenth switch is reserved. Please refer to the section 1.2.3 to 1.2.6 for detailed settings. Notes: The default dome address is 0. The default baudrate is 2400, and the default status of the 120Ω terminator is OFF. The speed dome is self-adaptive to the Pelco-P, Pelco-D and Private-Code.
9 Installation Manual of 4-inch Speed Dome 1 31 ON OFF OFF OFF OFF ON ON ON ON ON Table 1-2 Set the Dome Address between 0 and 31 Switch Number Dome Address 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 1 2 3 4 5 OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF OFF OFF ON ON O
10 Installation Manual of 4-inch Speed Dome 1.2.2 Baudrate Settings The number 6 and 7 DIP switches are used for setting the baudrate of the speed dome. The baudrate can be 2400bps, 4800bps, 9600bps and 19200bps. The baudrate will be set as 2400bps by default if it is out of this range. Refer to the following table: Table 1-3 Set the Baudrate of the Dome Switch Number 6 7 OFF ON OFF ON OFF OFF ON ON Baudrate 2400 4800 9600 19200 1.2.
11 Installation Manual of 4-inch Speed Dome The alarm provides the relay output (no voltage), and the external power supply is required when it connects to the alarm device. For DC power supply (left diagram), the input voltage must be no more than 12VDC, 30mA. For AC power supply (right diagram), the external relay must be used (right diagram) to prevent damages to the speed dome and avoid risk of electric shock.
12 Installation Manual of 4-inch Speed Dome Chapter 2 Mount Introduction 2.1 Wall Mount The appearance and dimension figures of the wall mount are shown as follows.
13 Installation Manual of 4-inch Speed Dome 2.2 Pendant Mount The appearance and dimension figures of the pendant mount are shown as follows.
14 Installation Manual of 4-inch Speed Dome Chapter 3 Mounting Applications 3.1 Wall Mounting Before you start: Wall mounting is applicable to the indoor/outdoor solid wall. Notes: The wall must be thick enough to mount the expansion screws. The wall must be strong enough to withstand more than 4 times the weight of the dome and its accessories. Steps: 1. Drill screw holes as shown in Figure 3-1. 1) Attach the wall mount to the wall where you need to install the speed dome.
15 Installation Manual of 4-inch Speed Dome VIDEO Cables Connector Figure 3-2 Speed Dome and Wall Mount VID EO Figure 3-3 Secure the Dome to the Mount 3. Route the cables and secure the wall mount. 1) Route the cables for the speed dome. Please refer to the section 1.1.2 Connecting the Cables for connecting the video, network, power, RS-485, alarm and audio, etc. cables. 2) Tighten the set screws to secure the wall mount to the wall with the speed dome.
16 Installation Manual of 4-inch Speed Dome Set Screws Figure 3-4 Secure the Wall Mount 3.2 Pendant Mounting Before you start: Pendant mounting is applicable to the indoor/outdoor solid ceiling. Notes: The ceiling must be thick enough to mount the expansion screws. The ceiling must be strong enough to withstand more than 4 times the weight of the dome and its accessories. Steps: 1. Install the mounting base. 1) Drill four φ12 holes in the ceiling according to the screw holes of the mounting base.
17 Installation Manual of 4-inch Speed Dome Mounting Base Cable Hole Adapter Hook For Safety Rope Figure 3-5 Install the Pendant Pole 2. Install the speed dome to the mount. 1) Connect the safety rope of speed dome to the hook of pendant pole. Safety Rope VIDEO Connector Hook For Safety Rope Figure 3-6 Safety Rope 2) Connect the safety rope of speed dome to the hook of pendant pole. 3) Rotate the connector of speed dome to the wall mount.
18 Installation Manual of 4-inch Speed Dome Figure 3-7 Secure the Speed Dome 3.3 In-ceiling Mounting Before you start: The in-ceiling mounting is applicable to the indoor ceiling. Notes: The height of the space above the ceiling must be more than 250mm. The ceiling must be with the thickness between 5 and 40mm. The ceiling must be strong enough to withstand more than 4 times the weight of the dome and its accessories. Steps: 1. Drill holes in the ceiling.
19 Installation Manual of 4-inch Speed Dome Figure 3-8 Drill Template 2. Dissemble the speed dome. 1) Loosen three screws as shown in the following figure. 2) Remove the lower dome. Three Screws Figure 3-9 Dissemble the Speed Dome 3. Install the toggle bolts. 1) Remove the toggle from the toggle bolt. 2) Insert the bolts into the screw holes on the dome as shown in Figure 3-10. 3) Rotate the bolts through the screw holes. 4) Reinstall the toggles as shown in Figure 3-11.
20 Installation Manual of 4-inch Speed Dome Toggle Bolt Holes Figure 3-10 Toggle Bolt Holes Toggle Bolt Figure 3-11 Install the Toggle Bolts 4. Align the toggle bolts with the screw holes on the ceiling. 5. Push the dome to the mounting hole on the ceiling. 6. Rotate the bolts again. The toggle will automatically rotate down to secure the dome to the ceiling.
21 Installation Manual of 4-inch Speed Dome Toggle Ceiling Figure 3-12 Install the Dome to the Ceiling 7. Attach the lower dome to the speed dome. 8. Secure the lower dome with three screws as shown in Figure 3-13. Screws Figure 3-13 Install the Lower Dome 9. Route the cables through the ceiling for the speed dome. Please refer to the section 1.1.2 Connecting the Cables for connecting the video, network, power, RS-485, alarm and audio, etc. cables.
22 Installation Manual of 4-inch Speed Dome Figure 3-14 Finish the Installation Figure 3-15 Ceiling Mounting Sketch
23 Installation Manual of 4-inch Speed Dome Appendix Appendix 1 Lightning & Surge Protection This product adopts TVS plate lightning protection technology to avoid damage caused by pulse signal that is below 3000W, like instantaneous lighting, surging, etc. According to the actual situation outdoors, necessary protection measures must be taken to secure the electrical safety. The distance between signal transmission line and High-voltage equipment or high-voltage cable is at least 50m.
24 Installation Manual of 4-inch Speed Dome Appendix 2 RS485 Bus Connection General Property of RS485 Bus According to RS485 industry bus standard, RS485 is a half-duplex communication bus which has 120Ω characteristic impendence, the maximum load ability is 32 payloads (including controller device and controlled device). RS485 Bus Transmission Distance When using 0.
25 Installation Manual of 4-inch Speed Dome faraway. At this time, the dome will be uncontrollable, or self-running, etc. Figure A-4 Star Shape Connection For such case, the best way is adding a RS485 distributor. This product can effectively change the star-shape connection to which satisfies the requirement of RS485 industry standard, in order to avoid those problems and improve the communication reliability. Show as figure 5.
26 Installation Manual of 4-inch Speed Dome Appendix 3 24VAC Wire Gauge & Transmission Distance The following table has described the recommended max. distance adopted for the certain wire gauge when the 24VAC voltage loss rate is less than 10%. For the AC driven device, the maximum voltage loss rate allowable is 10%. For example, for a device with the rating power of 80VA which is installed at a distance of 35 feet (10m) away from the transformer, then the minimum wire gauge required is 0.8000mm.
27 Installation Manual of 4-inch Speed Dome Appendix 4 Wire Gauge Standards Bare Wire Gauge (mm) Americ an Wire Gage (Brit ish)St andard Wire G auge Cross-sectional Area of Bare Wire AWG 2 SWG mm
