36" x 84" Parts List & Installation

PVC Barn Door Assembly and Track Installation H Style 36”
4. Attach Stile to
Bottom Rail
Lay one of the Stiles (A)
onto work surface. Make
sure the side with the large
holes are facing outward.
Insert one of the
Reinforcement plates (B)
into the bottom of the Stile
into the innermost
chamber of the Stile.
See Figure 3.
5. Install Center Rail
Place 2 of the 4” screws (Z) into the pre-drilled holes in the stile,
making sure they are fully inserted. Snap a center rail stopper
(F) into the channel between the 2 screw shafts. Once in place,
snap each screw shaft into the outer channels of the stopper.
Place the Center rail (E) against the screws, lining up the holes
in the extrusion. Once in place, tighten the screws until stile and
rail are ush and secure. Do not overtighten. See Figure 5.
7. Insert Door Panels
Take the starter panel for the
bottom of the door (L1),
making sure the smaller
opening side is inserted rst.
See Figure 10.
Slide this panel into the bottom
door section (between the
bottom and center rails).
Make sure piece ts snug into
stile channel. Gently tap into
place with the rubber mallet.
Next take a bottom door panel
(J) with the tongue side facing
the rst panel and slide it into
the channel. Again tap into
place and make sure it ts
snug. Continue with remaining
panels (J) for this section.
Repeat these steps for the
starter top panel (L2) and top
door panels (K) in the top
section of the door. These will
be a tighter t to slide and tap
into place.
Figure 3
Place 2 of the 4” screws
(Z) into the 2 holes in the
outside of the channel.
Make sure they are fully
inserted. See Figure 4A
& 4B
Slide a reinforcement clip
(D) into the channel and
over the screw shafts.
Place the end of the
Bottom rail (C) against the
screws, lining up the holes
in the extrusion.
See Figure 4B
Once in place, tighten the
screws until stile and rail
are ush and secure.
6. Install Top Rail
Insert U bracket (G) into the Top of
the stile into the outside channel
and the innermost channel. The side
of the U clip with the larger holes
should be facing the outside edge
of the door. The top of the U clip
will rest on the top of the stile once
inserted. See Figure 7.
Place 2 of the 4” screws (Z) into the
2 holes in the outside of the Stile
channel. Make sure they are fully
inserted. Slide a reinforcement clip
(D) into the channel and over the
screws shafts. See Figure 6.
Insert two small screws (Q) into the
oval holes on top of the U bracket
and secure to the top of the stile.
Take 2 small screws (Q) and secure
into the oval holes in the outside
of U bracket (G). This will be the
outside channel of the stile. See
Figure 7.
Line up Top Rail (C) with Stile. Make
sure the side of the Top rail with
the thinner channel is facing down
towards the bottom of the door.
Place the end of the Top rail (C)
against the screws, lining up the
holes in the extrusion. Once in
place, continue tightening screws
until stile and rail are ush and
secure. This will be the top of the
door. See Figure 8.
Bottom
Rail
Middle
Rail
TopRail
Side Stile
Starter Panel
Bottom
Rail
Middle
Rail
TopRail
Side Stile
Starter Panel
Bottom
Rail
Middle
Rail
TopRail
Side Stile
Starter Panel
Bottom
Rail
Middle
Rail
TopRail
Side Stile
Starter Panel
Figure 4A
Figure 4B
Fig. 2A
Fig. 2B
Fig. 2C
Fig. 2A
Fig. 2B
Fig. 2C
Figure 5
Figure 6
Figure 7
Figure 8
Figure 10
Fig. 2A
Fig. 2B
Fig. 2C