Installation instructions

ManualsBrandsLucasey ManualsTVs & monitorsLC200DS2

Important! Please read all warnings and cautions before installing the mount.

Caution: Improper installaion of this wall mount may void the warranty on your monitor.

Caution: Wall attachment should be performed by qualified installers only, using construction methods prescribed

by authorized architects or engineers that comply to all applicable codes and standards.

The maximum weight of each monitor to be installed on theLC200DS2 is 75Lbs. (34.1 Kg.)

Inspect all parts to make sure there is no shipping damage. Do not install if any parts are damaged.

Please call 1-800-LUCASEY or 1-510-534-1435 if you have any questions about this installation.

LC200DS2

Double Stud Dual Articulating Wall Mount

for Flat Panel Screens up to 32"

with up to 200mm x 200mm VESA® Mounting Patterns

Multi-position triple pivoting arms allows you to position

the monitor in hard to reach areas. Use the LC200DS2

with flat screens up to 75 Pounds. Ideal for concealing

cord connections in the wall behind the flat screen.

Designed to mount to structures with 16"

wall studs.

The monitor can be pushed into or pulled away from the

wall as needed. The dual pivot points and relocatable

wall arm position allow for flexibility in monitor placement.

The viewing angle can be adjusted 45 for the best

viewing angle.

Wood lag screws are provided for wood stud installations.

Concrete anchor bolts or Toggle bolts for metal studs

can be ordered separately using part numbers:

WMAAB6 or WMATB6.

Open pattern of wall plate allows access holes to be cut

into wall.

Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1

Page 1 of 5

LC200DS2 INSTALLATION INSTRUCTIONS

Summary of content (5 pages)

PAGE 1
Page 1 of 5 LC200DS2 Double Stud Dual Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA® Mounting Patterns Multi-position triple pivoting arms allows you to position the monitor in hard to reach areas. Use the LC200DS2 with flat screens up to 75 Pounds. Ideal for concealing cord connections in the wall behind the flat screen. Designed to mount to structures with 16" CL wall studs. The monitor can be pushed into or pulled away from the wall as needed.
PAGE 2
Page 2 of 5 LC200DS2 INSTALLATION INSTRUCTIONS WARNING: The structure to which the mount is attached needs to be capable of supporting five times the stated load limit. Additional reinforcement of the structure to which the mount is attached may be necessary and a certified architect or engineer is needed to make this determination. WARNING: Take into consideration the combined weight of the mount, the monitor and any auxiliary equipment when determining the total load on the wall and mount.
PAGE 3
Page 3 of 5 LC200DS2 INSTALLATION INSTRUCTIONS LC200DS2 Front View 19-1/4" 3" Min. Projection 11-1/4" LC200DS2 Wall Plate 5" Inside arm folds past outside arms for closest to the wall home position. 5" 16" LC200DS2 Top View Straight LC200DS2 Top View Showing Pivots Pivot point for articulation (Can be relocated for best monitor viewing locaiton) Pivot point for articulation LC200DS2 Tilted Side View Pivot point for articulation 24.7" 45 Max.
PAGE 4
LC200DS2 INSTALLATION INSTRUCTIONS Page 4 of 5 Wall Bracket Wood Lag Screws are provided for 16" on center wood stud installations. If you are installing onto metal studs follow the toggle bolt instructions on page 5. If installing into concrete, use our WMAAB6, concrete anchor bolt kit. See http://www.lucasey.com for details and drawings of all available mount accessories. 1.
PAGE 5
Page 5 of 5 LC200DS2 Tilted Side View Monitor Tilt Adjustment 1. Carefully loosen, but do not remove, theTilt Adjustment Screw. Do not loosen more than is needed to make the monitor moveable. See Detail A. 2. Slide the monitor into the appropriate viewing angle 45 . C 3. Tighten the Tilt Adjustment Screw and make sure the monitor can not be moved. Monitor Removal Detail A 1. With one person holding the monitor in place, have a second person remove the 5/16-18 Hex Bolt from the mount Pivot Point. 2.