LUCCI AIRFUSION RADAR DC CEILING FAN INSTALLATION OPERATION MAINTENANCE WARRANTY INFORMATION CAUTION READ INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION AND FAN OPERATION. V1.
Airfusion Radar Installation Instructions CONGRATULATIONS ON YOUR PURCHASE Congratulations on purchasing the latest in energy saving ceiling fans. This fan runs on DC (direct current) power which gives it the benefit of being super energy efficient whilst still maintaining high volume airmovement and silent operation. Energy Saving - The DC motor is the latest technology in fan design. Its highly efficient motor saves up to 65% more energy than ceiling fans with traditional AC motors.
Airfusion Radar Installation Instructions PARTS LIST Unpack your fan and check the contents. You should have the following: Fig. 1 1. Mounting bracket with EMI filter x 1 7. Remote transmitter with holder x 1 set (12V 23AE Battery included) 2. Fan assembly x 1 8. Blade screw x 7 3. Motor housing x 1 9. Mounting screw bag: 4. Blade x 3 5. Blade kit x 3 6.
Airfusion Radar Installation Instructions INSTALLING THE MOUNTING BRACKET If there isn’t an existing outlet box, then install one using the following instructions: Disconnect the power by removing the fuses or turning off the circuit breakers. Secure the outlet box (A) (not included) directly to the building structure. Use appropriate fasteners and materials (not included). The outlet box and its bracing must be able to fully support the weight of the moving fan (at least 35 lbs).
Airfusion Radar Installation Instructions HANGING THE FAN MOTOR ASSEMBLY Lift the fan assembly to the mounting bracket (1) and let the J-hook of the mounting bracket (4) go through the hole of the hanging plate and hang up the fan assembly (3). Fig. 6 Connect the male and female connector together (2). Fig. 6 Complete the electrical wiring using the diagram below (Figure. 7). Fig.
Airfusion Radar Installation Instructions FINISHING THE INSTALLATION INSTALL THE CANOPY COVER Loosen 2 screws (2) from the mounting bracket. Fig.8 Loosen 2 screws (1) by half thread from the mounting bracket. Fig. 8 Lift the hanging plate of the fan assembly up to the mounting bracket and let the L-shape slot on the hanging plate go through the screws (1) on the mounting bracket.
Airfusion Radar Installation Instructions LIGHT KIT INSTALLATION (Light kit sold separately) Note: Light kit must be installed by a licensed electrician. NOTE: The light kit is available for selected ceiling fan models and as an optional light kit. 1. Remove the bottom cover from shaft (A). 2. Remove the shrinkable tube (B) from light wires connector (C). 3. For light kit installation, please refer to light kit installation user guide. Fig.
Airfusion Radar Installation Instructions Transmitter / Receiver pairing for Ceiling fan 2: Turn off the mains supply to the receivers of both ceiling fans 1 and 2. Install the 12V DC battery in the compartment. Please make sure the polarity of the battery is correct. Fig.11 Change the position of the DIP switches in the transmitter 2, so that it will be different to transmitter 1. Turn on the power to receiver 2. Keep the power OFF to receiver 1.
Airfusion Radar Installation Instructions D - LIGHT CONTROL BUTTON: (Light kit sold separately) Press the button to turn the light ON/OFF. Press and hold the button to access the light dimming function. E – D / ON SWITCH This switch marked D/ON controls the dimming function of the lights. If using non-dimmable bulbs, use a ballpoint pen or small screwdriver to set the switch to “D” to disable the dimming function. If using dimmable halogen bulbs, set the switch to “ON” to enable the dimming function. Fig.
Airfusion Radar Installation Instructions INSTALLING THE TRANSMITTER HOLDER Remove the cover (A) from the holder (B). Install the holder (B) with the two screws provided (C). Replace the cover (A) into holder (B). Fig. 14 Fig. 14 AFTER INSTALLATION WOBBLE: NOTE: ceiling fans tend to move during operation due to the fact that they are mounted on a rubber grommet. If the fan was mounted rigidly to the ceiling it would cause excessive vibration.
Airfusion Radar Installation Instructions TECHNICAL INFORMATION Fan Size 52” CT Speed Volts Amps Watts RPM (V) (A) (W) Extra-High 120 0.46 33.65W 205 Medium High 120 0.22 15.08W Low 120 0.06 3.08W CFM CFM/ N.W. G.W. C.F. W (lbs) (lbs) 5327.70 158.32 10 12 1.29 150 3838.77 254.56 10 12 1.29 50 1091.20 354.28 10 12 1.29 These are approximate measurements. They do not include data for any lamps or fixtures attached to the ceiling fan.
Airfusion Radar Installation Instructions ENHORABUENA POR SU ADQUISICIÓN Enhorabuena por la compra de lo último en ventiladores de techo de bajo consumo. Este ventilador utiliza una corriente CC (corriente continua) para conseguir un gran ahorro de energía y proporcionar un elevado volumen de desplazamiento de aire y una operación silenciosa. Ahorro de energía - El motor CC incorpora la última tecnología en diseño de ventiladores.
Airfusion Radar Installation Instructions interferencias en instalaciones residenciales. Este aparato genera, usa y puede irradiar energía en forma de radiofrecuencia. En caso de no ser instalado y utilizado de acuerdo con las instrucciones, podría causar interferencias en las comunicaciones de radio. LISTA DE PIEZAS Desembale el ventilador y compruebe el contenido. Debería incluirse lo siguiente: Img. 1 1. 1 soporte de armado con filtro EMI 7. 1 juego de transmisor remoto con soporte 2.
Airfusion Radar Installation Instructions INSTALACIÓN DEL SOPORTE MURAL Si no hay una caja eléctrica ya instalada, instale una siguiendo estas instrucciones: Corte la corriente quitando los fusibles o bajando los disyuntores. Asegure la caja eléctrica (A) (no incluida) directamente a la estructura del edifico. Utilice los elementos y materiales de fijación apropiados (no incluidos).
Airfusion Radar Installation Instructions COLGADO DEL CONJUNTO DEL MOTOR DEL VENTILADOR Eleve el conjunto del ventilador hacia el soporte de armado (1) y deje que el gancho en forma de J del soporte de armado (4) pase por el orificio de la placa de colgado y cuelgue el conjunto del ventilador (3). Img. 6 Conecte los conectores macho y hembra uno al otro (2). Img. 6 Complete el cableado eléctrico según se indica en el diagrama abajo (Img. 7). Img.
Airfusion Radar Installation Instructions CÓMO FINALIZAR LA INSTALACIÓN INSTALACIÓN DE LA TAPA DE LA CUBIERTA Afloje 2 tornillos (2) del soporte de armado. Img.8 Afloje 2 tornillos (1) media vuelta del soporte de armado. Img. 8 Eleve la placa de colgado del conjunto del ventilador hasta el soporte de armado y deje que la ranura en forma de L pase por los tornillos (1) del soporte de armado.
Airfusion Radar Installation Instructions INSTALACIÓN DEL KIT DE LUZ (el kit de luz se vende por separado) Nota: El kit de luz debe ser instalado por un electricista acreditado. NOTA: El kit de luz está disponible para algunos modelos de ventiladores de techo y es un kit opcional. 1. Retire la cubierta inferior del eje (A). 2. Retire el tubo retráctil (B) del conector de los cables de la luz (C). 3. Para la instalación del kit de luz, consulte el manual de instalación del kit de luz. Img.
Airfusion Radar Installation Instructions Encienda el ventilador 1 y cambie su velocidad desde el transmisor 1 para comprobar que está emparejado y funciona correctamente. Emparejamiento del transmisor y el receptor del ventilador de techo 2: Desconecte la corriente de los receptores de los ventiladores 1 y 2. Instale una batería de 12V CC en el compartimento. Asegúrese de instalarla en el sentido correcto de la polaridad. Img.
Airfusion Radar Installation Instructions Botones del mando a distancia A - BOTONES DE LA VELOCIDAD DEL VENTILADOR: Hay 6 velocidades disponibles. El botón «I» representa la velocidad más baja, y el botón «VI» la más elevada. NOTA: Cuando encienda el ventilador por primera vez o cambie el encendido al controlador, necesitará primero poner en marcha el ventilador a la velocidad «VI» y elegir después una velocidad más baja.
Airfusion Radar Installation Instructions Solución: A. Apague el ventilador de techo durante 30 segundos. B. En los 60 segundos siguientes a la conexión del receptor del ventilador de techo 2 a la corriente, pulse el botón «SET» del transmisor durante 6 segundos. Durante el proceso de emparejamiento del mando a distancia y el receptor del ventilador CC, el ventilador empezaráa girar automáticamente en sentido antihorario a sus revoluciones máximas durante 3 minutos.
Airfusion Radar Installation Instructions CUIDADO Y MANTENIMIENTO: La limpieza periódica de su ventilador de techo es el único mantenimiento que se requiere. Utilice un cepillo blando o un paño sin pelusa para no arañar el acabado de pintura. Por favor, corte la corriente cuando haga esto. No sumerja el ventilador de techo en el agua, dado que podría dañar el motor o las aspas y causar posibles descargas eléctricas.