LCTV- 2201A TFT-LCD Monitor Owner's Guide to Operation
LCTV-2201A COLOR TFT- LCD TV Monitor OPERATION MANUAL CONTENTS SAFETY PRECAUTIONS ……………3,4 SUPPLIED ACCESSORIES ……………5 PREPARATION Remote Control ………………………6 Cable Connection ……………………7 LOCATION OF USERS CONTROL ……8 BASIC OPERATION ……………………9 Monitor Installation ……………10,11,12 OSD USAGE Basic OSD usage …………………13 Basic Setup …………………………14 PC Setup ……………………………15 Video Setup …………………………16 ……………………………17 TV Setup PIP ……………………………………18 Zoom …………………………………19 …………………………20 OSD Setup Before Calling for repair service ……2
SAFETY PRECAUTIONS Improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your color TFT-LCD TV monitor product, please read the following precautions carefully before using the product. Ŋ Ŋ Ŋ Ŋ Ŋ All operating instructions must be read and understood before the product is operated.
SAFETY PRECAUTIONS (Continued) Ŋ Unplug the power cord from the AC outlet before cleaning the product. Use a damp cloth to clean the product. Do not use liquid cleaners or aerosol cleaners. Ŋ Unplug the power cord from the AC outlet if you do not use the product for considerably long time. Ŋ Do not use the product near water, such as bathtub, washbasin, kitchen sink and laundry tub, swimming pool and in a wet basement. Ŋ Keep the product away from direct rays of the Sun-light.
SUPPLIED ACCESSORIES Make sure the following accessories are provided with the product. LCTV-2201A TFT-LCD Monitor Owner's TM390 ... XGA Guide to Operation TM400 ...
PREPARATION Remote Control Ŋ Use the remote control by pointing it towards the remote sensor window. Objects between the remote control and sensor window may prevent proper operation. Cautions regarding use of remote control ! Ŋ Do not expose the remote control to shock. In addition, do not expose the remote control to liquids, and do not place in an area with high humidity. Ŋ Do not install or place the remote control under direct sunlight. The heat may cause deformation of the unit.
PREPARATION (Continued) Cable Connection Rear view of main unit Power input (DC 15V) S-VIDEO VIDEO ANALOG RGB (PC) TV Antenna Sound out PC SOUND VIDEO SOUND 7
LOCATION OF USERS CONTROL Control Panel (C/P) on the front of main unit Menu Source Menu Signal source select Channel up / Move up Channel down / Move down Decrease volume Increase volume ő CH ŏ ő VOL ŏ Power Power Indicator Remote control (R/C) Power Channel select Press to select channels over 99 - Channel number 100 ~ 125 Channel Add / Erase Press - Memory current channel Press again - Erase current channel Auto Program Menu Select item Sound mute Press - Stops sound Press again Returns sound to
Available Mode Ŋ Yes / ŋ No Ŋ PC Ŋ Video Ŋ S-Video Ŋ TV BASIC OPERATION POWER On / Off / Standby Ŋ by Control Panel (C/P) 1 Press the Power button to turn on the main unit. 2 The power indicator lights green. 3 Press again the Power button to turn off. Ŋ by Remote Control (R/C) 1 Press the Power button to turn on the main unit. 2 Power indicator changes from red to green.
Monitor Installation 1 Double click [Control Panel ] icon from [My Computer] folder. 3 Select [Settings] in [Display Properties] window. 4 Click [Advanced...]. 10 Available Mode Ŋ Yes / ŋ No Ŋ PC ŋ Video ŋ S-Video ŋ TV 2 Double click [Display] icon from [Control Panel] folder. 5 Select [Monitor] in the window shown above. 6 Set [Refresh Frequency:] at 60Hz. 7 Finally, click [Properties].
Monitor Installation (Continued) 8 Select [Driver] and then click [Update Driver...]. 10 Click [Have Disk...]. Available Mode ■ Yes / □ No ■ PC □ Video □ S-Video □ TV 9 [Upgrade Device Driver Wizard] will be appeared. Choose the second list and then click [Next>]. 11 Select drive [A: ].
Monitor Installation (Continued) 12 Select the file of NEWCOMMMONITOR.inf. Available Mode ■ Yes / □ No ■ PC □ Video □ S-Video □ TV 13 Choose SOSA TM800 and then click [Next>]. SOSA TM800 SOSA TM800 14 Click [Next>]to start installing the selected monitor. 12 15 Click [Finish]. (Be sure the screen shows you correct model name.
BASIC OSD USAGE Main Menu Screen 1 Press the Menu of R/C or C/P to display the OSD menu screen. 2 Press the Chŏ ŏ/ő ő of R/C or C/P to move the cursor to desired menu icon. 3 Press the Sel of R/C or Menu of C/P to select the menu icon. 4 Press the Exit of R/C or select the Exit of OSD menu to disappear the main menu screen.
Available Mode Ŋ Yes / ŋ No Ŋ PC Ŋ Video Ŋ S-Video Ŋ TV Basic Setup Selected item Press the Volő of R/C or press the Chő of C/P Press the Volŏ of R/C or press the Chŏ of C/P Brightness Decrease brightness Decrease brightness Contrast Decrease contrast Increase contrast Color RESET Bluish Cold Medium Hot Reddish 1 Press the Sel of R/C or Menu of C/P to select the RESET. 2 Press the Volŏ/ő ő of R/C or press the Chŏ/ő ő of C/P to move the cursor to the Yes or No.
Available Mode Ŋ Yes / ŋ No Ŋ PC ŋ Video ŋ S-Video ŋ TV PC Setup Selected item Auto Adjust Press the Volő of R/C or press the Chő of C/P Ŋ Press the Press the Volŏ of R/C or press the Chŏ of C/P Sel of R/C or Menu of C/P then progress adjustment automatically Ŋ Automatically adjusted items are bellow 1) Frequency 2) Phase 3) H-position of PC Setup 4) V-Position of PC Setup 5) Canceling Speaker Mute 6) Turning a zoomed picture into its normal shape (100%) Note: Hot key to auto adjust : Press Chŏ and Ch
Available Mode Ŋ Yes / ŋ No ŋ PC Ŋ Video Ŋ S-Video Ŋ TV Video Setup Selected item Press the Volő of R/C or press the Chő of C/P Press the Volŏ of R/C or press the Chŏ of C/P Saturation Lower color intensity Higher color intensity Hue Toward green Toward purple Scaling Fill ...... The screen takes the source of 4:3 or 16:9 aspect ratio as its full-sized regular picture. Aspect Ratio ...... They are the same aspect ratio with that of Source.
Available Mode Ŋ Yes / ŋ No ŋ PC ŋ Video ŋ S-Video Ŋ TV TV Setup Selected item Channel system Press the Volő of R/C or press the Chő of C/P 1 Press Sel of the R/C Press the Volŏ of R/C or press the Chŏ of C/P or Menu of C/P to display below menu. US Air US Cable Japan Air Japan Cable 2 Press Chŏ/ő ő of R/C or C/P to move cursor to required OR channel system, then press Sel of the R/C or Menu of C/P for select. 2 Press CH. Search of the R/C and select Auto Program.
Available Mode Ŋ Yes / ŋ No Ŋ PC ŋ Video ŋ S-Video ŋ TV PIP Selected item PIP Press the Volő of R/C or press the Ch of C/P Ŋ PIP function is only available in PC mode. Off Source On Ŋ PIP signal source selection. TV H-Position Press the Volŏ of R/C or press the Chŏ of C/P Video move left the PIP window S-Video move right the PIP window ŋ V-Position move down the PIP window ŋ TV Channel ŋ move up the PIP window ŋ Ŋ TV Channel change. Press Chŏ /Chő of R/C or C/P to select desired channel.
Available Mode Ŋ Yes / ŋ No Ŋ PC Ŋ Video Ŋ S-Video Ŋ TV ZOOM Selected item Zoom Press the Volő of R/C or press the Chő of C/P Press the Volŏ of R/C or press the Chŏ of C/P Zoom out Zoom in Original screen Zoom screen A A V-Pan Ŋ Move the zoom window up and down while operating the Zoom. move down the zoom window move up the zoom window A H-Pan A Ŋ Move the zoom window sideways while operating the Zoom.
Available Mode Ŋ Yes / ŋ No Ŋ PC Ŋ Video Ŋ S-Video Ŋ TV OSD Setup Selected item Language Press the Volő of R/C or press the Chő of C/P Press the Volŏ of R/C or press the Chŏ of C/P 1 Press the Sel of R/C or Menu of C/P to select the Language. Then appears language select menu screen. 2 Press the Volŏ/ő ő of R/C or press the Chŏ/ő ő of C/P to move the cursor to the English or Korean. 3 Press the Sel of R/C or Menu of C/P to select the desired language. Then press Exit to move to previous menu screen.
Before calling for repair service... Ŋ Before calling for repair service, check the following items for possible remedies to the encountered symptoms. Problem There is no picture or sound (TV,Video,PC). Check below Reference Pages • Make sure the AC adapter is properly inserted in the power outlet. • Make sure the main power button of the main unit is on. • Make sure the signal cable is free of connections. • Make sure whether the power of an external input device is on.
SPECIFICATIONS LCTV-2201A Color TFT-LCD TV Monitor Resolution Color 1600 * 1024, WSXGA Standard Color 16,777,216 Colors Max, color (Dithering) Full Color Brightness 200 cd/m2 (nit) Lamp life 25,000 hours Contrast Ratio 300 : 1 Viewing Angle H : 140 V : 140 Panel PC Signal (Anlog RGB) Video / TV Type Amorphous Si TFT-LCD Actual Display Size 470.4 * 301.1mm Diagonal Length 22.0 , 558.8mm H-Frequency 30~80 KHz V-Frequency 43~75 Hz Signal Level 0.
SPECIFICATIONS Available PC VGA Mode VGA Input Signal Resolution V-Frequency (Hz) H-Frequency (KHz) Pixel Rate (MHz) Standard Type 640 x 350 85 37.9 31.500 VESA Standard 640 x 400 85 37.9 31.500 VESA Standard 720 x 400 85 37.9 35.500 VESA Standard 60 31.5 25.175 Industry Standard 72 37.9 31.500 VESA Standard 75 37.5 31.500 VESA Standard 56 35.1 36.000 VESA Guidelines 60 37.9 40.000 VESA Guidelines 72 48.1 50.000 VESA Standard 75 46.9 49.
