Operating Instructions Hydraulic Tools 84112/5601-85 GB Issue 1.2005 PO6 - Hydraulic Power Pack replaces 5.98 PO GO = driven by 4stroke petrol engine = driven by electric motor 6 1E 2E 1D Operation of 1 resp. 2 single-acting cylinders Series 10 25 50 70 Nominal size of oil container in l Operation of 1 double.
1 Basic operation and designated use of the machine 1.1 The machine has been built in accordance with state-of-the-art standards and the recognized safety rules. Nevertheless, its use may constitute a risk to life and limb of the user or of third parties, or cause damage to the machine and to other material property. 1.
General safety instructions 3.1 In the event of malfunctions, stop the machine immediately and lock it. Have any defects rectified immediately. 3.2 Before starting up or setting the machine in motion and during operation of the machine make sure that nobody is at risk. 3.3 Before transporting the machine always check that the accessories have been safely stowed away. 3.4 Make sure that there is enough lighting during work. 3.5 Avoid any operation that might be a risk to machine stability. 3.
.4 Always tighten any screwed and thread connections that have been loosened during maintenance and repair. Observe the stipulated torques. 4.5 Work on the electrical system or equipment may only be carried out by a skilled electrician himself or by specially instructed personnel under the control and supervision of such electrician and in accordance with the applicable electrical engineering rules. 4.6 The electrical equipment of machines is to be inspected and checked at regular intervals.
6.1.5 Power packs with 25 l oil container The oil container is filled ex works with 15 l of hydraulic oil. If necessary, the oil container can be filled up to a total volume of 24 l. The filler plug for hydraulic oil (fig. 1) includes a dipstick with 2 marks: 1 = standard oil level 15 l ; 2 = max. oil level 24 l Filler plug for hydraulic oil 6.2 Control valves A number of control valve versions is available to meet different operator’s requirements. 6.2.
8 Lifting with single-acting jacks 8.1 Power pack type PO6 - 1E and GO6 - 1E 8.1.1 Connection Remove the screw plug at connection A of the valve block and screw in hose connection nipple. Connect pipe or hose to cylinder. Connection "T" stays locked. fig. 2 8.1.2 Operation (see fig. 2) Start the motor and close drain valve (turn hand wheel 1 to the right to fully closed position) so the jack extends with the motor running. The load holding function can be obtained by switching the motor off.
9.1.2 Operation Each cylinder movement can be controlled by the 4/3-way valve. Position I Position 0 Position II (A) Extended position. (Centre position of the oper. lever) Load holding function with oil flow from P ---> T. (B) The cylinder is hydraulically retracted. The valve can be switched from the extended or the retracted position into the neutral position without pressure losses in the cylinder (positive overlap in the valve). 10 fig. 4 Preparations and Putting into Operation 10.
11.2 Carry frame To facilitate their transport, the power packs can be upgraded with a carry frame which must be ordered separately as a mounting kit. Ref. no. for power packs with 10l - tank V84150/7601-03. Ref. no. for power packs with 25l - tank - upon request. 11.3 Quick-connect couplings All power packs can be equipped with quick-connect couplings. Your LUKAS leader will be glad to offer you the couplings that you need. 12 Maintenance 12.
14 Technical data Type Ref. no. Type Ref. no. 500 bar 84112/ 700 bar 84112/ Oil capacity Usable oil cap. standard-max. standard-max. Weight* Motor ca. kg PO6-1E-10-50 5607 5601 7.5 l 6l Electric motor 34 PO6-2E-10-50 5608 5602 -- -- 230 V/50 Hz, 1,5 kW 36.5 9l 7.5 l electr. protection acc. 35 to DIN EN 60034-5 43 IP 54 41.5 PO6-1D-10-50 5609 5603 PO6-2E-25-50 5628 5622 PO6-1D-25-50 5629 GO6-1E-10-50 5610 GO6-2E-10-50 15 l - 24 l 10 l - 19 l 5604 7.
© Copyright 1998 LUKAS Hydraulik GmbH LUKAS Hydraulik GmbH A Unit of IDEX Corporation Weinstraße 39, 91058 Erlangen, Germany Postfach 2560, 91013 Erlangen, Germany Telefon (09131) 698-0 • Telefax (09131) 698-394 E-Mail: info@lukas.de 84112_5601_Ag105_e.
