SKU: NMF7K5BK00 NewAir 24” Outdoor Patio Pedestal Misting Fan Manual v1.
READ AND SAVE THESE INSTRUCTIONS. TABLE OF CONTENTS Register Your Product Online............................................................................... 3 Safety Information & Warnings ........................................................................... 4 Parts List ............................................................................................................... 5 Assembly & Installation .......................................................................................
REGISTER YOUR PRODUCT ONLINE Register Your NewAir Product Online Today! Take advantage of all the benefits product registration has to offer: Service and Support Diagnose troubleshooting and service issues faster and more accurately Recall Notifications Stay up to date for safety, system updates and recall notifications Special Promotions Opt-in for NewAir promotions and offers Registering your product information online is safe & secure and takes less than 2 minutes to complete: 0 newair.
SAFETY INFORMATION & WARNINGS Please read all instructions before using this misting fan. Failure to carefully read all instructions may result in possible electric shock or fire hazard and will void the manufacturer’s warranty. • Use this misting fan only as instructed in this owner’s manual. Other uses may cause electric shock, injury or fire. • Close supervision is required if this fan is used near children or pets.
PARTS LIST Check to insure the following parts are included with your product: • • • • • • • • • • 4 M6x16 screws large washers small washers nuts Stand pole fan base water pump metal pipe fan head water tank PRODUCT FEATURES • • • • • • • • Designed for cooling large areas such as patios, backyards, warehouses, and more.
ASSEMBLY & INSTALLATION It is strongly recommended that a second person be available to assist during the assembly process. DO NOT plug in the fan before assembly. This misting fan comes in two separate boxes. Carefully remove all packaging materials and retain for future storage/use. Make sure there is no residual foam left in any of the components. A screwdriver and wrench will be required to assemble this misting fan. STEP 1: ASSEMBLING THE STAND POLE 1. 2. Refer to diagram 1 below.
STEP 2: CONNECTING THE BACK PANEL 1. 2. 3. 4. Refer to diagram 2. Find the rectangular panel located on the back of the stand pole. Remove this back panel from the stand pole by completely unscrewing it from the stand pole. Set it aside. Locate the water pump. This is packaged separately from the stand pole and can be found in box #1. You will see 2 water hoses (1 large and 1 small) and 1 electric wire connected to the water pump.
STEP 3: CONNECTING THE WATER LINE 1. 2. 3. Refer to diagram 3. Locate the metal pipe and fan head and attach the fan head onto the pipe. The fan head should have 2 water hoses (1 large and 1 small) and 1 electric wire with male connector plug connected to it. Take the electric wire with the male connector that is located on the back of the fan head and thread it through hole D. Take the large water hose with 2 smaller water hoses within it and thread the entire piece through hole C.
STEP 4: CONNECTING THE FAN HEAD TO THE STAND POLE 1. 2. 3. 4. 5. 6. 7. 8. Refer to diagram 4. Place the stand pole/base on a level surface. Take the water hoses and electric wire from the fan head/pipe and thread them through the top of the stand pole. Do not attach the fan head to the stand pole yet. Connect the male and female connector plugs together. Take the small water hose from the fan head/metal pipe and connect it to the other valve opening attached to the back panel.
STEP 5: ASSEMBLING THE WATER TANK 1. 2. 3. Refer to diagram 5. Take the water pump and place it in the pump slot. Locate the water tank and place it on the fan base, making sure to line up the pump opening with the pump slot so that they fit together. Place any protruding hoses or wires into the tank. Put the tank cover over the tank. newair.
OPERATING INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. This misting fan can operate with optimal output in temperatures up to 104°F. Lift up the tank cover and fill the tank with clean water. Connect the fan to a power supply. Turn on the fan by pressing the red power switch. This misting fan has 3 different fan speeds. Turn the speed dial to adjust the fan speed. To start the misting function, press the misting button located on the stand pole. The misting function will only work if the fan speed is set.
CLEANING & MAINTENANCE Always unplug the misting fan from the power supply before servicing or cleaning. Regular cleaning and maintenance is an essential step in maintaining the longevity of your misting fan and ensuring that it operates free of defects. Maintain your misting fan by following these steps: • Use a soft cloth and a solution of mild soap and warm water to clean the fan’s exterior. Do not use harsh cleaners, gasoline, paint thinner, benzene, etc.
TROUBLESHOOTING Problem Possible Causes Solution The fan does not turn on. The power cord is not plugged in. Check to make sure the plug is plugged into an outlet. No mist is coming out of the unit. The water tank is empty. Make sure there is water in the tank. Water is leaking out of the water hose. The connections are not tightly secured. Check to make sure all of the fan’s components are securely connected together. The fan produces uneven mist. There is a leak in the water hose.
LIMITED MANUFACTURER’S WARRANTY This appliance is covered by a limited manufacturer’s warranty. For one year from the original date of purchase, the manufacturer will repair or replace any parts of this appliance that prove to be defective in materials and workmanship, provided the appliance has been used under normal operating conditions as intended by the manufacturer.