Owners manual

ManualsBrandsLund ManualsAutomotiveRX315SB Rivet Style Fender Flare Set Fits 18-19 F-150

Page 1 of 3

Installation Instructions

Important Safety Information

• CAUTION - Before driving, ensure that the fender flare is properly secured to vehicle.

• Do not use automatic “brush-style” car washes.

• Do not use cleaning solvents of any kind.

• Periodically check all components for tightness.

For proper installation and best possible fit, please read all instructions BEFORE you begin.

For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219.

NOTE: (Content shown below is for (4) piece installations. (2) Piece installations will contain smaller quantities.)

Driver side front Passenger side front Rubber Seal U-Clip x12

Offset Lever Clip x4

(RX Style only)

Rivet + Nylon Nut

x32

Driver side rear Passenger side rear

Tools Required

Contents

Custom Paint Job (Optional)

Please test fit all the flares first to ensure you have the correct flares for your vehicle. We are not responsible for any costs you may incur if you did not confirm the flares

before having it painted. We recommend hiring professionals to custom paint the products. It is also ideal to have the painting done prior to the installation to eliminate any

over-spraying issues.

Remove existing fender flares. (Skip this step if you don’t have existing fender flares.)

Remove all the screws and fasteners currently holding the existing flare to the vehicle. Write down and save all the screws you have removed for re-use with the Lund fender flares.

If certain areas of the existing flares are held on with double sided tape, you will have to pry your existing flare off. Please do so carefully to avoid damage to your vehicle body.

Test fitting.

Hold each and every flare up to the fender. Make sure you align the flare to the contour of the body, and the mounting holes lineup to the existing mounting holes on the inner

fender lip (if applicable). Don’t worry if not all the holes line up, as some holes are meant to be used with different installation hardware that is provided. The flares may not

be sitting flush at this time, our flares are designed to flex into the bodyline when you actually install them using the provided and existing hardware. At any time, do not drill

or modify the fender flare in anyway, as you will void your warranty.

Remove other existing parts.

Some vehicles may require the removal of existing parts that will interfere with the installation. Common item would be mud flaps; however by using fender flares, they act

as another form of mud deflector. If you are not confident in doing so, this will be a good time to take your vehicle to a professional for the installation. Save existing screws

and fasteners from the vehicle. NOTE: For 2014 Silverado, must remove and discard factory mudflaps on front wheel wells. For rear wheel wells, must remove and discard

the factory mudflaps attached to vehicle bed that are closest to the cab.

Cleaning the vehicle.

Make sure to wash your vehicle, especially the area the fender flares will be mounted to including the inner fender lip. Any dirt or debris that has not been cleaned or removed

can potentially cause the improper fitment of the fender flare. If you are covering existing rust, we recommend sanding down the rust and primer over to prevent further

deterioration of the metal in the fender. Make sure the vehicle is dry before the installation. The fender flares come ready to be installed, however if you need to clean them,

please use a mild detergent to wash and then dry completely.

Elite Series Fender Flares

Preparation Before Painting / Installation

Torx head screwdriverRazor Blade Hex Key 4.0 and 4.5 Socket Wrench

I - Sheet Number I315 Rev.A

Summary of content (9 pages)

PAGE 1
Installation Instructions I - Sheet Number I315 Rev.A Elite Series Fender Flares For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219. Important Safety Information • CAUTION - Before driving, ensure that the fender flare is properly secured to vehicle. • Do not use automatic “brush-style” car washes. • Do not use cleaning solvents of any kind.
PAGE 2
Preparation Before Painting / Installation For RX Style Only (SKIP if you have SX or EX style) Install the rivet screws and nuts to each of the rivet holes on the flare. Our rivets are designed to screw on to the fender flares only, and they shouldn’t be touching the vehicle body at all. Using hand tools, tighten nuts until fastener is snug. DO NOT OVERTIGHTEN as this may damage the fender flare. Installation of the Rubber Seal Before you start cutting any rubber seal, please study the diagram.
PAGE 3
Installation Steps U-Clip Installation NOTE: Actual application may vary slightly from illustrations. fender flare Fender Flare fender edge Sealant Body Panel 1 Due to building variations in trucks, it may be necessary to remove some sealant from inner lip of fender to allow installation on UClips. Lever Clip Installation 2 3 Press fender flare edge so that it is flush with fender edge. Press U-clip in place so that it encompasses both edge of fender flare and edge of fender.
PAGE 4
Instructions d'installation I - Feuille numéro I315 Rév.A Élargisseurs d'aile de la série Elite Veuillez lire l'ensemble des instructions AVANT d'utiliser le produit afin de garantir une installation correcte et un ajustement optimal. Pour obtenir une assistance technique ou demander des pièces manquantes, veuillez appeler le service clientèle au 1-800 241-7219. Consignes de sécurité importantes • PRÉCAUTION - Avant de conduire, vérifier que l'élargisseur d'aile est bien fixé au véhicule.
PAGE 5
Préparation avant la peinture/installation Pour le style RX uniquement (À IGNORER en cas de style SX ou EX) Fixez les vis et les écrous à riveter à chacun des trous de rivet sur l'élargisseur. Nos rivets ont été conçus pour être vissés sur les élargisseurs d'aile uniquement, et ils ne doivent en aucun cas toucher la carrosserie du véhicule. Utiliser des outils à main, serrer les écrous jusqu’à fixation est bien serré. NE PAS TROP car cela pourrait endommager l’arrondi de l’aile.
PAGE 6
Étapes de l'installation U-Clip de l’installation ÉLARGISSEUR D'AILE REMARQUE : l'installation réelle peut différer légèrement des illustrations. flare de l’aile bord de l’aile MASTIC PANNEAU DE CARROSSERIE 1 En raison de la construction de variations dans les camions, il peut être nécessaire d’enlever certaines étanchéité de la lèvre interne de l’aile pour permettre l’installation sur U-clips.
PAGE 7
Instrucciones de instalación I - Número de hoja I315 Rev.A Extensiones de guardabarros Serie Elite Para la instalación correcta y el mejor ajuste posible, lea las instrucciones ANTES de comenzar. Para pedir asistencia técnica u obtener partes que falten, por favor llame a Atención al cliente al 1-800-241-7219. Información importante de seguridad • PRECAUCIÓN: Antes de conducir, asegúrese de que la extensión del guardabarros esté debidamente asegurada al vehículo.
PAGE 8
Preparación antes de pintar o instalar Solo para el estilo RX (OMITA si tiene el estilo SX o EX) Instale los tornillos de remache y las tuercas en cada orificio de remache en la extensión. Nuestros remaches son diseñados para ajustarse únicamente en las extensiones de guardabarros y no deben tocar la carrocería del vehículo en ningún caso. El uso de herramientas de mano, apriete las tuercas hasta que cierre quede ajustada. NO APRIETE ya que esto puede dañar la llamarada guardabarros.
PAGE 9
Pasos de instalación U-Clip de instalación NOTA: La aplicación real tal vez no sea igual a las ilustraciones. flare fender EXTENSIÓN DEL GUARDABARROSFLARE PANEL DEL CUERPO 1 borde guardabarros Sellador Debido a las variaciones en la construcción de camiones, puede ser necesario eliminar algunos de sellador del labio interno de guardabarros para permitir la instalación en U-Clips.