assembly rad eee SU Marriott assembly. square hot radio subsystem parts & assembly . square bot said subsystem parts & assembly, continues The Ratio Subsystem provides the link between the EE transmitter antenna x1 bot and the human operator. Commands are entered through the joysticks and buttons on the Randi Transmitter, and sent through the air via FM radio waves 10 the Radio Receiver mounted on the robot.
Cee . square bot assembly square hot radio subsystem parts & assembly, conned Q For receiver assembly, continued: Basic Controller Operation The Redis Transmitter joysticks can be configured 10 work In (wo basis lengthen Installed receiver module should gook Hike this rations, To cheek or swathe between configurations, fellow these instructions: 1. Yuan on the Transmitter by pushing the Bower switch 10 the GH position, § CHANNEL, FY TRANSMITTER Bb. 2.
radicchio subsystem, cones Controller Trim Channel 4 {X-axis} Channel 3 Channel (X-axis) trim tm 3 Channel 4 Hutton button pg {rm trim button : button Br cause ihe sucks on the transmitter are wallow electromagnetically devices halt operate directly on circa voltage, there fs the distinct possibility Brat the theist wit became calibrates. This cheapness when tie sticks start deliverer different voltages tin wildcat the controller expects for gives position.
radio subsystem, co Transmitter Battery Voltage B CHANNEL FM TRANSMITTER internment In normal superstition, the transmission display ten numbers on the LUD scree tha configuration ember {see Appendix 55, and the battery voltage en the transmitting. Note at this screen only downplays the Cattery wore ich on the transit, and not the robot? There 1s ne way to Harmon ihe robe's batiste ‘wordage using this splay, 36 you will meet to watch separately for problems arising from low rubies battery power.
radio subsystem, wives Tether Port, continued To use the tether extreme: 1. Hook up ore end of the cable 10 the ack of your Nadia Transmitter, in the port marked “Tether Port” £ Plug the other end directly Into the Rx1 port of your Robot Anticancer. 3. ups the Transliterate an by pushing the power switch aa the Transmitter to the ON position. 4. Tues ye Rotation Controller or by Lapsing he power switch an the Robt Courtier to the ON propulsion. 5.
Tips, continued 1 ya accidental change a setting on sour conifer that you diktat want 16 ‘change, you can reset the controls tighten the CON FIG menu. Tre: the Transmitting on by pushing die power switch into the ON position. 2. Hold down the Mode son Select bunions for twa seconds unt the mend appears. TONES shooed be swattered by default. 3.
tarter kit Ves starter ki ~ The FCC Wants You to Kit ow “Iris equipment nas been tested and found to cornily with the limits far radii controlled devices, pursuant 1 Part 15 and Part 95 of the FOC Rufus These Grits ave designed 1 prov reasonable protection against harmful interference. This equipment generates, uses, and can radiate radio frequency energy 2nd, I nat installed and used in concerning with the instructions, may cause bar Interference 10 radio communications.
The Vex Robotics Design System is designed to be usable A A in competition settings with multiple robots on the field at the hack of together at the same time. In order for each robot to be able [NRE to tell which radio commands are intended for it, every robot needs to be listening for commands on a different radio channel (see Radio Subsystem background information). The radio channel is set hy the crystal that is installed in every radio transmitter and receiver.
Remove the old crystals from both the receiver and the transmitter, and store them safely for later use, Select a new receiver crystal and a new transmitter crystal, and be sure that they have the same frequency number! Insert the new crystals carefully anti the vacant slots carefully. Do not use force, or you may bend or break the pins. Starter kit 276-2151 Ch. 61 75.410MHz Additional Transmitter and Receiver 276-2153 Ch. 89 75.970MHz Additional Crystal Set #1 276-2171 75.490, 75.570, 75.810, 75.
