User's Manual

Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Made and printed in the U.S.A. 02/03 P/N 043-118 Rev. A
LIMITED WARRANTY
Lutron will, at its option, repair or replace any unit that is defective in materials or manufac-
ture within two years after purchase. For warranty service, return unit to place of purchase or
mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid. Telephone
the Lutron Technical Support Center toll free at 800-523-9466. After the two year period, a
pro-rated warranty applies to this product until eight years after the purchase. For more infor-
mation regarding this warranty contact your Lutron representative.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE
IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO TWO YEARS FROM PUR-
CHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION,
REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE,
OR IMPROPER OR INCORRECT REPAIR, OR DAMAGE FROM IMPROPER WIRING OR
INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUEN-
TIAL DAMAGES. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT
OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY,
OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state. Some states do not allow limitations on how long an implied warranty lasts,
so the above limitation may not apply to you. Some states do not allow the exclusion or limi-
tation of incidental or consequential damages, so the above limitation or exclusion may not
apply to you.
This product may be covered by one or more of the following U.S. patents: 4,835,343;
4,889,999; 5,170,068; 5,237,207; 5,248,919; 5,399,940; 5,637,930; 5,736,965; 5,798,581;
5,848,054; 5,905,422;5,982,103; D353,798; D439,220 and corresponding foreign patents.
U.S. and foreign patents pending. Lutron and HomeWorks are registered trademarks and the
HomeWorks Logo is a trademark of Lutron Electronics Co., Inc.
© 2003 Lutron Electronics Co., Inc.
Technical and Sales Assistance
If you need assistance, call the toll-free Lutron
Technical Support Center. Please provide exact
model number when calling.
[phone] (U.S.A., Canada and the Caribbean)
Other countries call:
Tel: [phone]
Fax: [phone]
Visit our Web site at www.lutron.com
FCC Information
Note: This equipment has been tested and found to comply with the limits for a Class B digi-
tal device, pursuant to Part 15 of the FCC rules. These limits are designed to provide rea-
sonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the seperation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could
void the user’s authority to operate this equipment.
Industry Canada Information
The term “IC:” before the radio certification number only signifies that Industry Canada tech-
nical specifications were met.
Troubleshooting Guide
Symptom Cause and Action
Light bulb(s) are burned out.
• Replace light bulb(s).
Switch on lamp turned OFF.
• Turn lamp switch ON.
Light bulbs are dioded.
• If dioded light bulbs (Sylvania Designer 16
TM or Philips PAR-
16TM) are being used, replace with non-dioded light bulbs.
Breaker is OFF.
• Turn breaker ON.
Cord is not plugged in.
• Plug in cord.
Lamp has an integral dimmer.
• Use a lamp without an integral dimmer.
Lamp 3-way switch not set to full.
• Turn lamp 3-way switch to full.
Solid-state control dissipation
• Solid-state dimmers internally dissipate about 2% of the total
connected load. It is normal for dimmers to feel warm to the
touch during operation.
Improper programming
• Check programming in the HomeWorks Utility.
Out of RF range
• Reposition RF Signal Repeater or RF Processor to be within
30 feet (9m) of control.
Light does not turn ON, but LEDs on Lamp Dimmer are ON.
Light does not turn ON, and LEDs on Lamp Dimmer are OFF.
Lamp Dimmer does not dim properly or lights flicker.
Lamp Dimmer is warm.
Lights don’t turn ON/OFF from Keypad.