User's Manual

ManualsBrandsLutron Electronics ManualsElectronicsTable-top Keypad

English

RR-T5RL

RR-T10RL

RR-T15RL

Lutron Elec tron ics Co., Inc.

7200 Suter Road

Coopersburg, PA 18036-1299

Made and print ed in the U.S.A. 05/10 P/N 044-164 Rev. B

Installation

Find a suitable location for the Tabletop Keypad. Place

the keypad in a convenient and accessible location within

30 ft (9 m) of an RF signal repeater.

Battery Installation

1. Remove the battery cover.

Troubleshooting Guide

Symptom Probable Cause and Action

The LEDs on

a DC adapter

powered keypad

do not turn on.

Power not present at the keypad.

• Verify that the DC adapter is plugged in.

Faulty DC adapter.

• Replace the DC adapter.

A battery

powered keypad

does not turn on

when a button is

pressed or turns

off immediately

after the button is

pressed.

Batteries are installed incorrectly.

• Install batteries as indicated in Battery Installation.

Batteries are not making contact with the battery terminals.

• Adjust the batteries so that they make contact with the battery

terminals.

Dead, low, or no batteries in the keypad.

• Install new batteries.

Dimmer, switch

or shade/drapery

not controlled by

Tabletop keypad.

The dimmer, switch or shade/drapery is not assigned to the keypad.

• Refer to the system Setup Guide to assign devices to a keypad.

Devices are out of range.

• Ensure all keypads, dimmers, switches and shades/draperies are

within 30 ft (9 m) of an RF signal repeater.

The lamp(s) is(are) burned out.

• Replace lamp(s).

Either there is no power to the device or the FASS

™

switch is

pulled out.

• Ensure that all devices are powered and all FASS switches

are pushed in.

Dimmer, switch

or shade/drapery

does not go to

desired level or

position when a

scene is selected.

The system is not programed correctly.

• Refer to the system Setup Guide to program the system correctly.

Devices are out of range.

• Ensure all keypads, dimmers, switches and shades/draperies

are within 30 ft (9 m) of an RF signal repeater.

All LEDs on the

keypad ﬂash

when any button

on the keypad is

pressed.

The keypad is in Factory Settings mode and has not been programed

into a system.

• Refer to the system Setup Guide to program the keypad correctly.

Note: Refer to the system Setup Guide for additional

troubleshooting suggestions.

Returning Keypads to Factory Settings

Returning a keypad to its Factory Settings will remove the

keypad from the system and erase all programming.

Step 1: Triple tap and hold any button (except the raise/

lower buttons) on a keypad. DO NOT release the

button after the third tap.

Step 2: Keep the button pressed on the third tap until all

the LEDs start to flash slowly (approximately 3

seconds).

Step 3: Immediately release the button and triple tap it

again. The status LEDs will flash quickly. When the

LEDs stop flashing, the device has been returned to

factory settings.

Warranty: For warranty information, please see

the Warranty enclosed with the product, or visit

www.lutron.com/resiinfo

Lutron, RadioRA, and the sunburst logo are registered trademarks and RadioRA 2 and FASS are trademarks of Lutron Electronics Co., Inc.

Installation Instructions

Please Read Before Installing

Tabletop Keypad

RR-T5RL, RR-T10RL, RR-T15RL

3 V or 9 V 300 mA

DC Adapter: T120-9DC-3

Input: 120 V 60 Hz 6.5 W

Output: 9 V 300 mA

Typical Power Consumption*: 0.6 W

Batteries: 2 AAA alkaline 1.5 V each

Mounting slots

Technical Assistance:

U.S.A. / Canada: 1.800.523.9466

Mexico: +1.888.235.2910

Other Countries: +1.610.282.3800

24 hours a day, 7 days a week.

Plug in

power

cord and

adapter

Optional Wall Mounting

1. Attach the wall bracket to the wall using the screws and

wall anchors provided with the keypad.

DC Adapter Installation

1. Plug the power cord into the Tabletop Keypad and the

DC adapter into an outlet.

Note: The DC adapter does NOT charge batteries.

Rechargable batteries should NOT be used with Tabletop

Keypads.

3. Replace battery cover.

Setup

To program the system refer to the system Setup Guide.

2. Install batteries as shown. Use two (2), 1.5 V AAA

alkaline batteries only.

2. Wrap excess power supply cord (if using DC adapter)

around the cord holder. Align keypad mounting slots and

snap onto the wall bracket.

Use these instructions to install the model numbers listed above. For

system setup instructions and tools visit: www.lutron.com/radiora2

Important Notes

Codes: Install in accordance with all local and national electrical codes.

Battery Power: Use only high quality AAA alkaline batteries. Battery powered

Tabletop Keypads will shut off after a short period of inactivity in order to conserve

battery power. Press any button on the Tabletop Keypad to turn it on.

Do not use rechargeable batteries. Using improperly rated batteries

could damage the keypad.

WARNING: Risk of re, explosion and burns. May result in serious injury

or death. DO NOT recharge, disassemble, crush, puncture, heat above

212 °F (100 °C) or incinerate the battery. Do not dispose of batteries

in normal household waste. Please recycle batteries, take to a battery

disposal facility, or contact your local waste disposal provider regarding

local restrictions on the disposal or recycling of batteries.

DC Adapter Power: Use only the DC adapter supplied with the keypad.

Using a DC adapter not rated for the proper specications could

damage the keypad and possibly overheat the DC adapter. Refer to the ratings

shown at the top of page.

Environment: Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C),

0 to 90% humidity, non-condensing. Indoor use only.

Cleaning: To clean, wipe with a clean damp cloth. DO NOT use any chemical

cleaning solutions.

RF Device Placement: RF dimmers, switches, keypads and shades/drapes

must be located within 30 ft (9 m) of an RF signal repeater. Remote dimmers and

switches are not required to be within a specific range.

Engraving: The Prepaid Engraving Certificate included with the keypad can be

reedeemed for a custom engraved button / faceplate kit. To order an engraved

button / faceplate kit please follow the instructions located at

www.lutron.com/buttons

Note: To avoid operation issues, Lutron recommends that the keypad, DC adapter

and wall bracket should not be painted.

NOTICE:

Typical Power Consumption test conditions: all backlights on medium intensity,

nightlight mode enabled , six LEDs on (two presets active per column), keypad

NOTICE:

Summary of content (4 pages)

PAGE 1
English Installation Instructions Please Read Before Installing RR-T5RL RR-T10RL Tabletop Keypad RR-T5RL, RR-T10RL, RR-T15RL 3V or 9 V 300 mA DC Adapter: T120-9DC-3 Input: 120 V 60 Hz 6.5 W Output: 9 V 300 mA Typical Power Consumption*: 0.6 W Batteries: 2 AAA alkaline 1.5 V each Installation Find a suitable location for the Tabletop Keypad. Place the keypad in a convenient and accessible location within 30 ft (9 m) of an RF signal repeater. Battery Installation 1. Remove the battery cover.
PAGE 2
Español Instrucciones de instalación Por favor, lea antes de instalar Teclado de Mesa RR-T5RL, RR-T10RL, RR-T15RL 3V or 9 V 300 mA Adaptador de CC: T120-9DC-3 Entrada: 120 V 60 Hz 6,5 W Salida: 9 V 300 mA Consumo típico de potencia*: 0,6 W Baterías: 2 alcalinas AAA de 1,5 V cada una Instalación Busque una ubicación apropiada para el Teclado de Mesa. Coloque el teclado en una ubicación conveniente y accesible, dentro de los 9 m (30 pies) de distancia de un repetidor de señales de RF.
PAGE 3
Français Directives d’installation Veuillez Lire avant l’Installation RR-T5RL RR-T10RL Clavier de table RR-T5RL, RR-T10RL, RR-T15RL 3V or 9 V 300 mA Adaptateur C.C. : T120-9DC-3 Entrée : 120 V 60 Hz 6,5 W Sortie : 9 V 300 mA Consommation typique*: 0,6 W Piles : 2 AAA alcaline 1,5 V chacune Installation Trouvez un endroit adéquat pour placer le clavier de table. Localisez-le dans un endroit pratique et accessible à moins de 9 m (30 pi) d’un répétiteur de signal RF. Installation des piles 1.
PAGE 4
Português Instruções de Instalação Leia antes de instalar RR-T5RL RR-T10RL Prenda de mesa RR-T5RL, RR-T10RL, RR-T15RL 3V or 9 V 300 mA Adaptador de CC: T120-9DC-3 Entrada: 120 V 60 Hz 6,5 W Saída: 9 V 300 mA Consumo normal de energia*: 0.6 W Baterias: 2 alcalinas AAA de 1,5 V cada Instalação Encontre um local adequado para o prenda de mesa. Coloque-o em um lugar conveniente e acessível, dentro de 9 m (30 pés) de um repetidor de sinais de RF. Colocação das baterias 1. Remova a tampa do porta-baterias.