User's Manual

Roller Shade
• Installation and Setup Guide—Please Read Before Installing and OperatingBattery Powered Window Shade with RF Wireless Remote Control
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
09/2013
P/N 045404 Rev. A
Lutron, O, Serena and Pico are registered trademarks of Lutron Electronics Co., Inc.
Equal depth
both sides
A
1
Mounting the shade rail:
3
Hanging the shade:
2
Installing the end caps on optional fascia:
2.1 Press-fit an end cap on the open end of the fascia as shown.
2.2 Repeat on the other end.
3.1 Facing the window, tilt the top of the shade assembly
C
away from you and insert its top rear edge into the channel
in the shade rail
A
.
3.2 Push the bottom of the shade toward the window and lock it
into the shade rail with a “click.”
1.1 Hold the shade rail
A
up to the mounting surface. Approximate
its final position and use a pencil to mark mounting screw
locations on the shade rail.*
1.2 Pre-drill the shade rail
A
at the pencil marks.
1.3 Fasten the shade rail
A
, to the mounting surface using the mounting screws provided
B
or other appropriate fasteners.
NOTE: The shade rail features
grooves to help stabilize the point
of your drill bit.
**NOTE: Depending on the size
of your shade and the depth of
your trim, or the roll direction of
your shade, you may be able
to mount the shade directly to
the wall above the trim without
additional spacing.
In this arrangement, the top
of the shade rail must be a
minimum of 4
1
/2 in (114 mm)
above the top of the trim.
Optional fascia/end caps
not shown
NOTE: If your shade was ordered with optional fascia, the fascia
will be factory-attached and wrapped with the shade. Leave the
wrapping in place during installation for added stability, then remove
the wrap before installing batteries.
*To ensure the shade rail is properly mounted, we rcommend:
a. Install mounting screws 6-12 in (152-305 mm) from each end of the
shade rail.
b. Locate the mounting screws so that they drive into studs or solid
trim. For other surfaces, use appropriate expansion anchors, toggle
bolts, or other fasteners, (not included).
c. Verify that the mounted
shade rail is level and
parallel to the window
opening.
#2 Phillips Driver Bit
1/8 in (3.2 mm) Drill Bit
Pencil
Level
D-Cell Alkaline Batteries
(6 or 8 depending on shade size)Power Drill
OPTIONAL
(1) Shade Rail
A
Mounting Screws
B
Serena® Roller
Shade Assembly
C
(1) Fascia with end caps
D
CLICK!
CLICK!
A
B
A
C
A
Outside
Mount
on Trim
Outside Mount
above Trim
A
Spacer blocks
or board
(not included)
securely
mounted to wall
above trim**
GROOVES
Worldwide Headquarters | USA
Lutron Electronics Co., Inc. 7200 Suter Road, Coopersburg, PA 18036-1299 USA
TEL: [phone] • FAX: [phone]
Technical Support: 1.800.523.9466 • Toll Free: 1.888.LUTRON1
Email: [e-mail] • Online: www.lutron.com/shadingsolutions
Europe Headquarters | United Kingdom
Lutron EA Ltd. 6 Sovereign Close, London, E1W3JF, UK
TEL: [phone] • FAX: [phone]
Technical Support: +44.(0)20.7680.4481
FREEPHONE: 0800.282.107
Inside
Mount
B
B
Included in the box:
Other items you’ll need:
End Caps
Left end cap
shown
Left end cap
installed
Fascia
Left Right
NOTE: If your shade will be inside-
mounted, both end caps must be
installed and fully seated before
proceeding to the next step.
4.5 in
(114 m m)
min.
Wall
Regular
roll
Reverse
roll
Trim