User's Manual

ManualsBrandsLutron Electronics ManualsElectronicsWirless Lighting Controller

Table Of Contents

032402a qs triac quick.eng.pdf

LUTRON

Control Unit

Quick Installation

and Operation Guide

Please Read

The GRAFIK Eye® QS control unit allows for control

of both lights and shades, without interfaces, using

a single control unit. Features include pushbutton

scene recall, info screen that displays energy savings

and status, IR receiver, astronomic timeclock, contact

closure input, and engravable backlit buttons that are

easy to find and operate.

Model Numbers: QSGRJ-3P, QSGRJ-4P, QSGRJ-6P

QSGR-3P, QSGR-4P, QSGR-6P

120 V

50/60 Hz

220 - 240 V

50/60 Hz

Unit Capacity (watts) 2000 W 3000 W

MLV 2000 VA

1600 W

3000 VA

2400 W

Zone Capacity (watts) 25 – 800 W 40 – 1200 W

MLV 25 – 800 VA

25 – 600 W

40 – 1200 VA

40 – 960 W

See page 6 for IEC PELV/NEC

® Class 2 ratings.

For California residents only:

The batteries in these devices contain

Perchlorate Material – special handling may apply.

For more information visit

www.dtsc.ca.gov/hazardouswaste/perchlorate

Contents

Features and Functions of the

GRAFIK Eye® QS Control Unit . . . . . . . . . . . . . . . . . 2

Wiring the GRAFIK Eye® QS Control Unit

Overview of Line Voltage/Mains Wiring . . . . . . . . . 3

Line Voltage Wiring Details. . . . . . . . . . . . . . . . . . . 4

Overview of IEC PELV/NEC® Class 2 Wiring . . . . . 6

QS Link Control Wiring Details. . . . . . . . . . . . . . . . 7

Power Group Wiring Example . . . . . . . . . . . . . . . .8

Completing Installation of the

GRAFIK Eye® QS Control Unit . . . . . . . . . . . . . 9

Programming Mode

Entering and Exiting Programming Mode . . . . . . 10

Navigating Menus in Programming Mode . . . . . . 10

Wireless Mode. . . . . . . . . . . . . . . . . . . . . . . . . 11

FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Zone Setup

Assigning Load Types. . . . . . . . . . . . . . . . . . . . . . 12

Assigning Non-Dim Load Type. . . . . . . . . . . . . . . 12

Setting Load Types . . . . . . . . . . . . . . . . . . . . . . . . 13

Scene Setup

Setting Zone Levels, Fade Rates,

and Shade Group Actions . . . . . . . . . . . . . . . . .14

Occupancy Sensor Setup. . . . . . . . . . . . . . . . 15

Scene Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Configuring Occupancy Sensor Settings

(optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Pico® Wireless Control Setup:

Associating with a GRAFIK Eye® QS

Wireless Control Unit . . . . . . . . . . . . . . . . . . . . .18

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 19

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Contact Information . . . . . . . . . . . . . . . . . . . . 20

For additional features and advanced functions,

see the complete installation and operation guide at

www.lutron.com/qs

English

Español

Français

Summary of content (20 pages)

PAGE 1
® Control Unit Quick Installation and Operation Guide Please Read Contents Features and Functions of the GRAFIK Eye® QS Control Unit . . . . . . . . . . . . . . . . . 2 Wiring the GRAFIK Eye® QS Control Unit Overview of Line Voltage/Mains Wiring . . . . . . . . Line Voltage Wiring Details . . . . . . . . . . . . . . . . . . Overview of IEC PELV/NEC® Class 2 Wiring . . . . QS Link Control Wiring Details . . . . . . . . . . . . . . .
PAGE 2
Features and Functions of the GRAFIK Eye® QS Control Unit Hinged faceplate Zone numbers Zone raise/lower buttons Zone LEDs display current lighting zone levels { Optional Shade button groups Preset and raise/lower buttons with integral LEDs (maximum of 3 button groups) Hinged faceplate OK Timeclock button Displays current timeclock info OK button Used for programming Infrared receiver For handheld remote use Info screen Displays status or programming functions Master buttons Temporarily raise and low
PAGE 3
Wiring the GRAFIK Eye® QS Control Unit: Overview of Line Voltage/Mains Wiring 1 2 A B C 1 2 3 4 1 2 3 4 5 6 L N Line Voltage/Mains Cables and Load Wiring 1 2 3 4 5 6 L N Terminal labels: L: Hot/Live N: Neutral : Ground 1-6: D immed/Switched line voltage outputs 120 - 127 V or 220 - 240 V Distribution Panel 2 AWG (4.
PAGE 4
Wiring the GRAFIK Eye® QS Control Unit: Line Voltage Wiring Details • Use properly certified cable for all line voltage/mains cables. • Proper short-circuit and overload protection must be provided at the distribution panel. You can use up to a 20 A circuit breaker for your installation. • Install in accordance with all local and national electrical codes. • IEC PELV/NEC® Class 2 terminals may be temporarily unplugged for ease of IR, occupancy sensor, and control wiring. • Notice: Risk of damage to unit.
PAGE 5
Wiring the GRAFIK Eye® QS Control Unit: Line Voltage Wiring Details (continued) Step 4: Connect line voltage and loads to control unit. • Strip 9 in (8 mm) of insulation off the line voltage/mains cables in the wallbox. 9 in (8 mm) • Connect the line voltage/mains, ground, and load wires to the appropriate terminals on the back of the control unit. L: Hot/Live N: Neutral : Ground Terminals 1-6: Dimmed/Switched line voltage outputs The recommended installation torque is 5.0 in∙lb (0.
PAGE 6
Wiring the GRAFIK Eye® QS Control Unit: Overview of IEC PELV/NEC® Class 2 Wiring 1 2 IR Wiring 18 AWG (1.0 mm2) each terminal From external IR connection (by others) 1: IR DATA 2: IR COM 1 2 A B C A B C 1 2 3 4 1 2 3 4 Contact Closure Input Wiring 1 2 3 4 5 6 L N 1 2 3 4 5 6 L N 1 2 24 V 50 mA For settings, see the full installation and operation guide at www.lutron.com/qs.
PAGE 7
Wiring the GRAFIK Eye® QS Control Unit: QS Link Control Wiring Details LUTRON LUTRON LUTRON seeTouch® QS wallstation GRAFIK Eye® QS control unit LUTRON QS smart power panel LUTRON LUTRON Sivoia® QS shade/drape LUTRON LUTRON Daisy-Chain Wiring Example Sivoia® QS shade/ drape GRAFIK Eye® QS control unit GRAFIK Eye® QS control unit LUTRON LUTRON Wire Gauge Less than 500 ft (153 m) Power (terminals 1 and 2) 1 pair 18 AWG (1.
PAGE 8
Wiring the GRAFIK Eye® QS Control Unit: Power Group Wiring Example On the QS link, there are devices that supply power and devices that consume power. Each device has a specific number of Power Draw Units (PDUs) it either supplies or consumes. A Power Group consists of one device that supplies power and one or more devices that consume power; each Power Group may have only one power-supplying device.
PAGE 9
Completing Installation of the GRAFIK Eye® QS Control Unit 1. Mount the control unit in the wallbox as shown using the four screws provided. Note: Follow all local and national electrical codes when installing IEC PELV/NEC® Class 2 wiring with line voltage/mains wiring. 2. Verify installation: • Restore power. • Press the top scene button. The LED will light. • Press the zone raise and lower buttons. Make sure the control unit is dimming all connected loads. 3.
PAGE 10
Programming Mode Entering and Exiting Programming Mode Entering programming mode: Main menu 2 4 5 6 Press and hold 1the top and3 bottom scene Timeclock buttons simultaneously for 3 seconds. The Scene setup LEDs in the scene buttons will scroll from top to bottom, confirming that you are in programming mode, and the info screen will display the main menu. Exiting programming mode: Scene 1 Press and hold the top and bottom scene Fade time buttons simultaneously for 3 seconds.
PAGE 11
Wireless Mode Many models of the GRAFIK Eye® QS control unit support wireless communication with other Lutron products. This feature allows for easy integration of wireless sensors, keypads, remotes, and shades for single-room wireless applications, as well as compatibility with other Lutron wireless systems such as RadioRA® 2. (See the RadioRA® Setup Guide; Lutron PN 044254.) Units supporting wireless communication are labeled “GRAFIK Eye® QS Wireless” on the front label of the unit.
PAGE 12
Zone Setup 1 2 Assigning Load Types 1. Enter programming mode. Main menu 2. Use the Master buttons to highlight CCI Setup “Zone setup” and press the Zone setup OK button to accept. 3. Use the Master buttons to highlight “Load type”. Press the OK button to accept. See “Setting Load Types” Zone Setup table on the next page. Load Type 4. Use the zone raise/lower buttons to Non-Dim Load Type choose the load type for that zone. See the list on the next page for supported load types.
PAGE 13
Zone Setup (continued) Setting Load Types Direct control via GRAFIK Eye® QS control unit Control via power module or interface LUTRON Power module or interface LUTRON LUTRON Zones 1–6 Fixture load type Choose this load type from the menu on the GRAFIK Eye® QS control unit: Incandescent Incandescent MLV (magnetic low-voltage) MLV Power module ELV (electronic low-voltage) — Power module Hi-Lume®/Eco-10® — Fluorescent module 0-10 V — Fluorescent module Non-dim lighting loads Non-dim Non-
PAGE 14
Scene Setup Setting Zone Levels, Fade Rates, and Shade Group Actions 1. Enter programming mode. Main menu 2. Use the Master buttons to highlight “Scene setup” and press Timeclock the OK button to accept. Scene setup 3. Use the Master buttons to highlight “Levels” to adjust lighting and/or shade levels. Press the OK button to accept. Use the Master buttons to highlight the scene number of your desired Scene setup scene. Press the OK button to accept. Levels 4.
PAGE 15
Occupancy Sensor Setup Associating wireless occupancy sensors and GRAFIK Eye® QS Wireless control units (for wireless enabled units only): 3 11 5 13 6 14 4 12 7 15 1 9 2 10 1. Make sure the wireless mode of the GRAFIK Eye® QS control Main menu unit is “Enabled”. Zone Setup 2. Enter programming mode. Sensor Setup 3. Use the Master buttons to highlight “Sensor setup” and press the OK button to accept. 4.
PAGE 16
Occupancy Sensor Setup Scene Mode This step allows you to assign up to four occupancy sensors to the GRAFIK Eye® QS control unit. Selecting Sensors Occ Sensor 1. If not already done, associate occupancy sensors and set to Setup “Scene Mode”. 2. Use the Master buttons to highlight “Setup” and press the Labels OK button to accept. The info screen will display “Searching” while the unit detects available occupancy sensors. 3.
PAGE 17
Occupancy Sensor Setup Configuring Occupancy Sensor Settings (optional) Occupancy Sensor Settings Main menu Note: These settings affect all sensors assigned to the Zone Setup GRAFIK Eye® QS control unit. Sensor Setup Grace Period: If the GRAFIK Eye® QS control unit is transitioning to an unoccupied state, motion detected within the grace period will return the lights to the previously Sensor Setup occupied level. Range: 15 – 30 seconds (default 15 seconds).
PAGE 18
Pico® Wireless Control Setup Associating the Pico® wireless control with a GRAFIK Eye® QS Wireless control unit: (for wireless enabled GRAFIK Eye® QS control units only) 3 11 5 13 6 14 8 16 4 12 7 15 1 9 2 10 1. Make sure the wireless mode of the GRAFIK Eye® QS control unit is Pico “Enabled”. Change type? 2. On the Pico® wireless control, press and hold the top (on) and bottom (off) buttons for 3 seconds. The info screen on the GRAFIK Eye® QS control unit Press OK will display the Pico® options.
PAGE 19
Troubleshooting Symptom Possible Causes Solution Unit does not power up Circuit Breaker is off Switch circuit breaker on Unit does not control loads Miswire Verify wiring to unit and loads Circuit breaker is tripping System short circuited Find and correct shorts System overload Verify zone/unit loading is within ratings (see Zone Setup section) Zone control does not work Miswire Make sure loads are connected to the right zones Zone control yields incorrect results Loose or disconnected wi
PAGE 20
Contact Information Warranty Lutron Electronics Co., Inc. One Year Limited Warranty For a period of one year from the date of purchase, and subject to the exclusions and restrictions described below, Lutron warrants each new unit to be free from manufacturing defects. Lutron will, at its option, either repair the defective unit or issue a credit equal to the purchase price of the defective unit to the Customer against the purchase price of comparable replacement part purchased from Lutron.