Specification Sheet
Table Of Contents
- Introduction
- Table of contents
- Scalable light management solutions
- New energy-saving products
- Four steps to selecting your control: Step 1
- Four steps to selecting your control: Step 2
- Four steps to selecting your control: Step 3
- Four steps to selecting your control: Step 4
- Dimmer families
- Vierti
- Vareo
- Nova T
- Nova
- Centurion
- Maestro
- Maestro IR
- Maestro Wireless
- Spacer System
- Diva
- Lyneo Lx
- MeadowLark
- Skylark
- Abella
- Ceana
- Ariadni
- Glyder
- Rotary
- Credenza and Attaché
- Maestro wallbox occupancy/vacancy sensors
- Radio Powr Savr wireless occupancy/vacancy sensors
- Radio Powr Savr wireless daylight sensors
- Wallplates and accessories: New Architectural
- Wallplates and accessories: Architectural
- Wallplates and accessories: Designer/Claro/Satin Colors
- Wallplates and accessories: Traditional/Fassada
- Mounting
- Ganging and derating
- Lighting load interfaces
- Wiring diagrams
- Glossary
- Visual index
- Patents and trademarks
Wallplates and accessories | Architectural
Receptacles for dimming use
•
Duplex for dimming both
connected loads
•
Projecting nubs prevent standard
plugs from being used
•
Requires replacement plugs for
dimming use
•
Includes 1-gang wallplate
Split duplex (half for dimming use)
15 A, 120/125 V* NTR-15-HFDU-AA
2
20 A, 120/125 V* NTR-20-HFDU-AA
2
Important application notes:
•
Receptacles and plugs for dimming use are UL
listed for use with all Lutron wallbox dimmers
included in this catalog
•
If there is only one electrical feed to the receptacle,
then the duplex DFDU must be used
•
If the hot and dimmed hot feeds to the split
duplex HFDU are supplied from different circuits
or split-wired, with separate switch-legs, a means
to simultaneously disconnect these circuits must
be provided at the panel board where they
originate (NEC 210.7(C) 2002 Edition). A 2-pole
circuit breaker or two single-pole circuit breakers
with an approved handle tie can be used to
accomplish this simultaneous disconnect. Feed-
through dimming panels, which are those without
breakers, are recommended when using the HFDU.
•
For detailed information, see Application Notes #91
(Guide to Dimming Table Lamps) and #109 (Guide
to Dimming Portable Lamps via Receptacles) at
www.lutron.com/applicationnotes
Duplex for dimming use
15 A, 120/125 V* NTR-15-DFDU-AA
2
20 A, 120/125 V* NTR-20-DFDU-AA
2
Receptacles for dimming use
•
Top half for dimming
•
Projecting nub prevents standard
plug from being used
•
Requires replacement plugs for
dimming use
•
Bottom half is a general use
receptacle and will fit standard
duplex plugs
•
Includes 1-gang wallplate
120/125 V RP-FDU-10-WH
White
120/125 V RP-FDU-10-BR
Brown
UL/CSA/NOM regulatory approvals
Replacement plugs for dimming
(use with receptacles)
•
This plug required for use with
Lutron
® receptacles for dimming
use—plug will work in standard
receptacle
•
Easily replaces the existing plugs
on lamps
AA
2
: Architectural matte color codes, see pg. 153
(1-gang wallplate included)
*Metal finishes are only available as separate
wallplates. Match with separate Black (BL)
controls and accessories.
158
www.lutron.com | 1.800.523.9466 |