User Guide

LED
up to 150 W
Incandescent
up to 600 W
Halogen
up to 600 W
quick-start guide
Lutron Smart Hub,
Pico remote control & dimmer
Welcome
—and thank you for purchasing a Caséta
dimming kit.
Before you install the dimmer, please
watch the installation video at
www.casetawireless.com/support
We hope you enjoy the convenience of
Caséta!
NOTE: You can mix and match dimmable LED,
halogen, and incandescent light bulbs with
Caséta dimmers.
Dimmable LED light bulbs vary in their dimming
performance. If you’re using these bulbs and they
flicker or turn off, please visit
www.casetawireless.com/lowend for information
on adjusting the dimmer for best bulb performance.
For a complete list of compatible dimmable LEDs,
please visit www.casetawireless.com/bulblist
Double your warranty
Works with energy efficient
dimmable light bulbs:
Tools you’ll need
Flat-head screwdriver
Phillips-head screwdriver
Pliers
Go to
www.casetawireless.com/support for additional troubleshooting suggestions.
Symptoms Probable cause and action
Light does not turn on or
dimmer LEDs do not
light up.
• Light bulb(s) burned out.
• Breaker is OFF or tripped.
• Light not properly installed.
• Wiring error.
• FASS switch on the dimmeris in the Off position.
Light does not respond to
Pico remote control.
• The dimmer is not properly paired with the Pico
remote control;
The Pico remote control can be paired with the
dimmer using the Lutron app.
• The dimmer is already at the light level the Pico
remote control is sending.
• The Pico remote control is outside the 30 ft
(9 m) operating range.
• The Pico remote control battery is low.
• The Pico remote control battery is
installed incorrectly.
• Bulbs turn off while
being dimmed.
• Bulbs turn on at high light
level but do not turn on at
a low light level.
• Bulbs flicker or flash when
dimmed to a low light level.
Verify bulbs are marked dimmable and visit
www.casetawireless.com/lowend for
information on adjusting the dimmer for best
bulb performance.
Load is Off and the light
bar blinks 4 times, pauses,
and repeats.
The dimmer is in Over Temperature Protection
(OTP) mode.
• See Step 3 Ganging and Derating. Ensure that
the dimmer is not overloaded.
• Reset the dimmer by using the Front Accessible
Service Switch (FASS); See Using your Controls
section. Pull out the FASS and push it back in.
Love Caséta dimmers? Have ideas for making
them better? Tell us what you think and we’ll
extend your warranty by 1 year.
www.casetawireless.com/register
CAUTION
Use only with permanently installed fixtures with
dimmable LED, halogen, or incandescent lamps.
To avoid overheating and possible damage to other
equipment, do not use to control receptacles, motor-
driven appliances, or transformer-supplied appliances.
!
CAUTION: Risk of Fire, Explosion, Leakage, and
Burns. Do Not Recharge, Disassemble, Heat Above
212 °F (100 °C) or Incinerate. This product contains
a lithium button/coin cell battery. Keep batteries away
from children. If a new or used lithium button/coin cell
battery is swallowed or enters the body, it can cause
severe internal burns and can lead to death in as little
as 2 hours. Always completely secure the battery
compartment. If the battery compartment does not
close securely, stop using the product, remove the
batteries, and keep the batteries away from children.
If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention. The battery in this device contains
Perchlorate Material — special handling may apply.
For more information, visit
www.dtsc.ca.gov/hazardouswaste/perchlorate
Codes
Install in accordance with all national and local
electrical codes.
Grounding
When no “grounding means” exist in wallbox, the
National Electrical Code (NEC®) allows a control to
be installed as a replacement if 1) a nonmetallic,
noncombustible faceplate is used with nonmetallic
attachment screws or 2) the circuit is protected by a
ground fault circuit interrupter (GFCI). When installing
a control according to these methods, cap or remove
green wire before screwing control into wallbox.
Use of the HomeKit logo means that an electronic
accessory has been designed to connect specifically
to iPod, iPhone, or iPad, respectively, and has been
certified by the developer to meet Apple performance
standards. Apple is not responsible for the operation of
this device or its compliance with safety and regulatory
standards. Please note that the use of this
accessory with iPod, iPhone, or iPad may affect
wireless performance.
FCC/IC Information
For FCC/IC information, please visit:
www.lutron.com/fcc-ic
Warranty
For warranty information, please visit
www.casetawireless.com/warranty
The Lutron logo, Lutron, Claro, Caséta, FASS, the Lutron Caséta & RA2
Select app logo, the design of the Pico remote, and Pico are trademarks
or registered trademarks of Lutron Electronics Co., Inc. in the US and/or
other countries. Apple, iPod, iPhone, and iPad are trademarks of Apple
Inc., registered in the U.S. and other countries. HomeKit is a trademark
of Apple Inc. App Store is a service mark of Apple Inc., registered in the
U.S. and other countries. All other product names, logos, and brands
are property of their respective owners.
© 2015-2023 Lutron Electronics Co., Inc.
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Troubleshooting
Device Ratings
Dimmer
DVRF-6L
120 V~ 50/60 Hz
Lutron Smart Hub *
L-BDG2 or L-BDGPRO2
5 V- 300 mA
Wallplate Bracket
PICO-WBX-ADAPT
Pico remote control
PJ2-3BRL
3 V- 10 mA
(1) CR2032 battery
(included)
Power supply
T-5DC-USB
Input: 100–240 V~
50/60 Hz 100 mA
Output: 5 V- 550 mA
Important notes:
1. For indoor use only
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C)
P/N 0302051 REV A
* Connect to a Class 2, LPS, or SELV, limited energy (<15 W) power
source only.
Using your Caséta by Lutron kit
Contents supplied
Dimmer
(DVRF-6L)
Claro wallplate
(CW-1)
Pico remote
control
(PJ2-3BRL)
Wire
connectors
Screws
(×5)
(×2)
Lutron
Smart Hub
(L-BDG2 or
L-BDGPRO2)
Power Supply
(T-5DC-USB)
Ethernet
Cable
A. Connect the smart hub to your Wi-Fi router using the Ethernet cable.
Smart
Hub
Router
B. Power
cord
Outlet
A. Ethernet cable
1 Press and hold “off” button on dimmer
2
Press and hold “off” button on remote
Install the Lutron Smart Hub
Download the Lutron app and walk through setup
Search for “Lutron Caseta”
B. Connect the power cord to the smart hub and plug it into an outlet.
WARNING: SHOCK
HAZARD! May result in
Serious Injury or Death. Turn off
power at circuit breaker or fuse
before installing.
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Installation for lights with one wall switch (single pole)
Installing your dimmer
1
Turn power off at circuit breaker!
4
Connect the dimmer
5
Mount the dimmer
6
Attach the wallplate
7
Turn power on at circuit breaker
* If your switch has more than 3 wires attached, see
“Installing Caséta in a 3-way switch application” video
at www.casetawireless.com/3way
1
2
3
Ground
1 Connect the bare copper (or green) “ground” wire
from the wallbox to the green wire on the dimmer
using one of the large supplied wire connectors.
2 Connect either of the remaining wires from the
wallbox to the black wire on the dimmer using one of
the large supplied wire connectors.
3 Connect the remaining wire from the wallbox to
the red wire on the dimmer using one of the large
supplied wire connectors.
4 Cap the blue wire coming from the dimmer with the
small supplied wire connector. The blue wire is not
used for single pole installations.
Note: Wire colors depicted in this install guide may
not match what is in your walls.
Use the mounting screws provided, leaving them loose
for this step.
2
Remove existing switch from wall
Remove the wallplate from switch. Remove the switch
and pull it away from the wall.
3
4
1
2
1
2
5
6
Ground
7
Disconnect all three wires* from the switch.
Important note:
Multi-gang installations may reduce the dimmer’s
maximum wattage rating. See the chart below for
maximum wattage information.
* For maximum wattage information when
mixing light bulb types see
www.casetawireless.com/ganging
Maximum* wattage derating chart
(120 V~ 50/60 Hz)
Load Type
Single
gang
Double
gang
Triple
gang
LED 150 W 150 W 150 W
or
*
Incandescent &
Halogen
600 W 500 W 400 W
Double Gang Triple Gang
3
Ganging and Derating
4
We’ve included instructions
for when a single switch is
controlling the lights. For
installation instructions when
two or more switches are
controlling a light, please visit
www.casetawireless.com/3way for complete
installation instructions and how-to videos.
Important note:
1 Attach the adapter to the dimmer using the
screws provided.
2 Tighten the mounting screws on the dimmer.
3 Snap on the wallplate.
‘snap’
3
1
2
Important notes:
1. For indoor use only.
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).
Pico remote control (sold separately)
Replacing light bulbs using FASS
Pull the FASS out on the dimmer to remove power at
the light socket.
On
Off
• Adjust slider to dim / brighten
the light level
• Will not turn lights off
FASS
Front Accessible
Service Switch
Dimmer
On
Off
Darker
Favorite
Brighter
To restore the original factory settings please go
to www.lutron.com/restore
Using your controls
x3
Hold for 6 seconds
until light bar
starts blinking.
1
Press and hold “off” button on dimmer
2
Press and hold “off” button on remote
Pairing the dimmer and Pico
remote control
Hold for 6 seconds until
lights flash 3 times.
Repeat steps to pair other Pico
remote controls.